|
|
04-19-2012, 08:45 PM
|
|
US Veteran
|
|
|
Join Date: Jan 2007
Location: Lexington, KY
Posts: 1,591
Likes: 118
Liked 1,179 Times in 379 Posts
|
|
UPDATE*****WWB 38 Special 130 grain...primer explodes!!!!
Met my son at a relatively new indoor range this afternoon to do some shooting. This range has balistic panel between lanes rather than a solid partition.
He picked up a box of WWB 38 special 130 grain FMJ to shoot out of my Model 66. He was on the 7th round (shells 30-35) when out of the corner of my eye I saw a bright flash. I immediately told him to stop firing (which he had all ready done) and to pop the cylinder and check the rounds. One round had not fired.
What happened is when the firing pin hit the primer, part of the primer blew away when it ignited. The flash came out of the primer (see middle picturte) and did not ignite the powder in the case.
Look on Winchesters web site, but found no way to contact them online.
Guess I fonnal have to do it the old fashioned way, see them a letter with the round and manufacturing number.
BTW, productin information is 27 56FB92.
**********UPDATE******************
Have the box of casings packaged up for UPS to pick up for Winchester. CS stated they were going to send me some certificates..not sure what they will be for, but something is better than nothing.
Last edited by Retired LTC, USAR; 04-23-2012 at 07:19 PM.
|
04-19-2012, 08:57 PM
|
Member
|
|
|
Join Date: Feb 2006
Location: Wellington FL Aberdeen NC
Posts: 1,614
Likes: 4,159
Liked 1,469 Times in 511 Posts
|
|
I'll bet you find no flash-hole in that round. It does happen on occasion.
__________________
Old paratrooper in NC
|
04-19-2012, 08:59 PM
|
Member
|
|
|
Join Date: Jan 2012
Location: God's Country
Posts: 4,711
Likes: 1,235
Liked 3,535 Times in 1,770 Posts
|
|
Primer was in the pocket sideways and had blocked the flash hole. It happens. I'm surprised he didn't notice it when he thumbed them into the cylinder.
I tried to find a telephone number for them also. Couldn't do it either.
|
04-19-2012, 09:13 PM
|
|
US Veteran
|
|
|
Join Date: Jan 2007
Location: Lexington, KY
Posts: 1,591
Likes: 118
Liked 1,179 Times in 379 Posts
|
|
I just posted on their facebook page with a picture of the primer. Lets see what kind of response that generates!!!!
|
04-19-2012, 10:35 PM
|
Suspended
|
|
|
Join Date: Jan 2007
Location: Sandy Utah
Posts: 8,747
Likes: 1,590
Liked 8,914 Times in 3,554 Posts
|
|
Read Michigan Scott's post. I copied your photo and blew it up, and he is absolutely correct, the primer was seated on its' edge.
Ammunition is a product that the end user has a responsibility to inspect 100% before use, and this is prime example of why. The simple reason is for your own safety. This is a defect easily detected, and a cartridge that should never have been loaded in the gun.
Instead of getting too upset trying to contact Winchester directly go to your local gun shop and ask them how you can contact the district marketing representative for Winchester. You will get farther, faster, with the rep. than you will posting on their Facebook page. BTDT, not just an off-the-wall suggestion.
What I was going to say was "......primer explodes!!!!", of course it did, that's what they are supposed to do!
Last edited by Alk8944; 04-19-2012 at 10:40 PM.
|
The Following 2 Users Like Post:
|
|
04-19-2012, 11:48 PM
|
Member
|
|
|
Join Date: Feb 2008
Location: The Peach State! GA!!!
Posts: 5,916
Likes: 14,318
Liked 6,257 Times in 2,328 Posts
|
|
Winchester will make it right. I had some Q3131 5.56mm ball that demonstrated some leakage around the primer pocket when fired in a Colt Hbar. They replaced all the ammunition paying all the shipping charges involved. They even replaced the ammo that I'd fired. Coo.
__________________
<><
|
04-19-2012, 11:53 PM
|
US Veteran
|
|
|
Join Date: Jun 2009
Location: SW Washington
Posts: 1,107
Likes: 616
Liked 288 Times in 168 Posts
|
|
Quote:
Originally Posted by Retired LTC, USAR
Met my son at a relatively new indoor range this afternoon to do some shooting. This range has balistic panel between lanes rather than a solid partition.
He picked up a box of WWB 38 special 130 grain FMJ to shoot out of my Model 66. He was on the 7th round (shells 30-35) when out of the corner of my eye I saw a bright flash. I immediately told him to stop firing (which he had all ready done) and to pop the cylinder and check the rounds. One round had not fired.
What happened is when the firing pin hit the primer, part of the primer blew away when it ignited. The flash came out of the primer (see middle picturte) and did not ignite the powder in the case.
Look on Winchesters web site, but found no way to contact them online.
Guess I fonnal have to do it the old fashioned way, see them a letter with the round and manufacturing number.
BTW, productin information is 27 56FB92.
|
What's the story on that primer in the case above the tilted primer? It appears to be pierced.
|
04-22-2012, 11:36 AM
|
Member
|
|
|
Join Date: Dec 2010
Location: Ohio
Posts: 32
Likes: 16
Liked 11 Times in 5 Posts
|
|
I was using this same ammo one time at an indoor range when I had a round that was very noticeably louder and offered heavier recoil - I was really glad I was using them in my 686 that day! I suspected a double charge.
|
04-22-2012, 11:49 AM
|
SWCA Member
|
|
|
Join Date: Jul 2005
Location: Indiana
Posts: 11,956
Likes: 10,147
Liked 10,129 Times in 4,801 Posts
|
|
Quote:
Originally Posted by Alk8944
...Ammunition is a product that the end user has a responsibility to inspect 100% before use, and this is prime example of why. The simple reason is for your own safety.
|
+ at least one-million. Look at every cartridge you put in your gun, no matter who made it.
|
04-23-2012, 07:21 PM
|
|
US Veteran
|
|
|
Join Date: Jan 2007
Location: Lexington, KY
Posts: 1,591
Likes: 118
Liked 1,179 Times in 379 Posts
|
|
******UPDATE******
Have the casings packaged and ready for UPS to pick up. They stated they are going to send me some certificates.........not sure what for.
BTW, if you want to contact Winchester by e-mail, you have to go to the Olin website and do it there.
|
04-24-2012, 03:16 AM
|
|
Moderator SWCA Member Absent Comrade
|
|
|
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
|
|
Quote:
Originally Posted by Retired LTC, USAR
******UPDATE******
They stated they are going to send me some certificates.........not sure what for.
|
They are going to send you a voucher for probably twice the value of the ammo you bought. (or more) It's their way of making up for the trouble you went through to send it back to them for inspection.
__________________
Freedom is never free!!
SWCA #3437
|
04-24-2012, 03:24 AM
|
|
Member
|
|
|
Join Date: Aug 2010
Posts: 520
Likes: 63
Liked 103 Times in 67 Posts
|
|
Two years ago I had a LCR revolver that seized up. I could not turn the cylinder or open it up until the gun cooled down. Then I had a difficult time extracting the shells. I was using Fiocchi and checked the box. I found two rounds that were a bit longer than the rest, similar to what was posted in the OP pics. I never used or bought any more of it. Scary to say the least.
|
04-24-2012, 03:30 AM
|
Member
|
|
|
Join Date: Feb 2010
Location: virginia
Posts: 1,001
Likes: 413
Liked 110 Times in 70 Posts
|
|
and............ this is why you inspect ammo before you put it in your gun.
|
04-24-2012, 03:46 AM
|
Member
|
|
|
Join Date: Feb 2009
Location: Border
Posts: 426
Likes: 86
Liked 262 Times in 129 Posts
|
|
People wanted cheap ammo so Win. is in the process of moving to MS and have folded their tent in IL and paying half the wages as before. Welcome to the Walmart world. 1,200 jobs lost. As you can see QC has gone out the window as once you shaft your employees co. loyalty goes with it.
|
04-24-2012, 04:50 AM
|
Member
|
|
|
Join Date: Mar 2005
Location: Phoenix, AZ
Posts: 727
Likes: 1
Liked 133 Times in 93 Posts
|
|
I have seen this before one time in a factory primed .357 mag case I had purchased for reloading. The metal cup on this particular primer was exceptionally thin. Just one of those things you can rarely come across. The company manufactures millions of primers and cartridges. Even with 6 sigma manufacturing one defect in a million is acceptable. A problem would be if every round exhibited the problem, one isn't a problem its an aberration.
|
04-24-2012, 09:26 AM
|
|
Member
|
|
|
Join Date: Dec 2002
Location: Ohio
Posts: 160
Likes: 19
Liked 19 Times in 10 Posts
|
|
As was mentioned above , inspect your rounds individually as you load them .
I've worked in retail guns for 26 yrs . Considering the billions of rounds manufactured it's understandable that "stuff happens" ... it's not just Winchester . I've seen Remington ammo with the primer upside down . Federal ammo with the bullet upside down .
In all cases the manufacturer replaced the ammo and then some . Give them a chance . They will make it right .
__________________
Mitch
|
04-24-2012, 10:08 AM
|
Member
|
|
|
Join Date: Dec 2010
Posts: 28
Likes: 0
Liked 0 Times in 0 Posts
|
|
I've had several problems with Winchester ammo.
I try to stay away from the white box variety if I can. However, if it is all I have, I do try to make a harder effort to inspect the ammo.
I've found terrible QC issues with the white box. .45 rounds with cases that were slightly fatter than they should have been and wouldn't feed into the breach. 9mm with primer issues.
The worst was a bullet that fell out of the casing while it was in the magazine of my conceal carry. I don't remember the Winchester label, but I do remember that there was gun powder all through out my firearm.
I mailed back the unused rounds and they sent me a certificate for a new box of ammo. I guess they thought I was going to make the same mistake twice.
|
04-24-2012, 10:42 AM
|
Member
|
|
|
Join Date: Nov 2011
Location: Hernando, Mississippi
Posts: 66
Likes: 21
Liked 9 Times in 3 Posts
|
|
Boge, I live in Mississippi and resent the inference that ammo made in Mississippi will be sub par. We are glad to have the jobs here and have a dedicated workforce. As with anything else a company has to stay competitive. When greedy workers demand too much companies will move.
Last edited by watergun1929; 04-24-2012 at 10:44 AM.
|
The Following 2 Users Like Post:
|
|
04-24-2012, 02:58 PM
|
|
Member
|
|
|
Join Date: Apr 2012
Location: Ontario Canada
Posts: 30
Likes: 0
Liked 0 Times in 0 Posts
|
|
Hey Gents, is it just my eyes, or does the round directly above the one in question (middle photo) show some color and deformation as well?
|
04-24-2012, 04:58 PM
|
US Veteran
|
|
|
Join Date: Jun 2009
Location: SW Washington
Posts: 1,107
Likes: 616
Liked 288 Times in 168 Posts
|
|
Quote:
Originally Posted by Shaunogun
Hey Gents, is it just my eyes, or does the round directly above the one in question (middle photo) show some color and deformation as well?
|
I tried pointing that out a couple of days ago. It looks pierced to me.
|
04-24-2012, 07:05 PM
|
Member
|
|
|
Join Date: Feb 2009
Location: Border
Posts: 426
Likes: 86
Liked 262 Times in 129 Posts
|
|
Quote:
Originally Posted by watergun1929
Boge, I live in Mississippi and resent the inference that ammo made in Mississippi will be sub par. We are glad to have the jobs here and have a dedicated workforce. As with anything else a company has to stay competitive. When greedy workers demand too much companies will move.
|
In 2009 21.9% of the people in your state lived in poverty. Winchester is locating there for one & one reason only & it isn't for the culture. They can pay dirt cheap wages and zero benefits. Enjoy the new plant in Oxford that Haley Barbour gave all the concessions to with Federal & YOUR state tax dollars as I'll never buy anything from them again if I can help it.
|
04-24-2012, 07:46 PM
|
|
US Veteran
|
|
|
Join Date: Sep 2006
Posts: 1,665
Likes: 117
Liked 1,119 Times in 511 Posts
|
|
Quote:
Originally Posted by Boge
People wanted cheap ammo so Win. is in the process of moving to MS and have folded their tent in IL and paying half the wages as before. Welcome to the Walmart world. 1,200 jobs lost. As you can see QC has gone out the window as once you shaft your employees co. loyalty goes with it.
|
The Illinois yankies were no better at loading, inspecting, or quality control. By the end of annual qualifications we had a coffee can full of Winchester Q loads that were duds, with crushed, sideways, or upside down primers, or inverted bullets. All from those great union members in Alton Illinois.
|
04-24-2012, 08:18 PM
|
|
Member
|
|
|
Join Date: Mar 2010
Location: Northwest Georgia
Posts: 832
Likes: 276
Liked 335 Times in 182 Posts
|
|
Glad there were no injuries,that's the important thing.
I think the company will have to do right by you on this one,as they certainly should.
__________________
Blessed be the Lord,my Rock
|
|
Posting Rules
|
|
|
|
|