|
|
05-11-2016, 09:49 AM
|
Member
|
|
|
Join Date: May 2016
Posts: 7
Likes: 0
Liked 0 Times in 0 Posts
|
|
Buffalo bore .44 mag
Hi guys, new to the forum but i was wondering if any of you have had problems with FTF from buffalo bore? I bought 2 boxes of .44 mag deer grenade buffalo bores, in the first box of 20 i had 6 misfires. I contacted buffalo bore about this and they claimed that it was a faulty gun. He stated that all the primer were set with a machine and could not be out of spec. Just visually looking at the FTF rounds you can see how much deeper the primer is set than the rounds that fired. I measured the FTF rounds primer depth and it was roughly .007"-.010" from round to round. I believe the spec is .005-.007". I mentioned this to the manufacturer and he said that he had been making ammo for 40+ years and it wasnt his ammo at fault. He also told me that i could email him all i want and he wouldnt respond any more. I have attatched a picture so you can see the difference in depth.
Sent from my SM-N920P using Tapatalk
|
05-11-2016, 10:14 AM
|
Member
|
|
|
Join Date: Feb 2015
Posts: 713
Likes: 129
Liked 719 Times in 327 Posts
|
|
The primer on the fired case looks very flat indicating at the very least the pressures were on the high end. Also looks like cratering which happens under excess pressure.
The unfired round looks as though it wasn't hit very hard at all and most likely not quite hard enough to set it off. The primer doesn't appear to be seated too deep but hard to tell from the photo. My guess is a combo of a hard primer and possibly a gun that has trigger work done to it with a lighter hammer spring? Again, this is just a guess.
|
05-11-2016, 10:19 AM
|
|
Absent Comrade
|
|
|
Join Date: Dec 2014
Location: Upstate SC
Posts: 12,990
Likes: 17,229
Liked 41,504 Times in 9,146 Posts
|
|
Welcome to the forum.
Seems customer service is a recurring theme here lately. The photo seems clear cut that something is amiss with their production. If you still want to get their attention, you could try copying your post, with picture, to their Facebook page.
https://www.facebook.com/pages/Buffa...12097152200394
|
05-11-2016, 10:31 AM
|
Member
|
|
|
Join Date: May 2016
Posts: 7
Likes: 0
Liked 0 Times in 0 Posts
|
|
Quote:
Originally Posted by Ballistic147
The primer on the fired case looks very flat indicating at the very least the pressures were on the high end. Also looks like cratering which happens under excess pressure.
The unfired round looks as though it wasn't hit very hard at all and most likely not quite hard enough to set it off. The primer doesn't appear to be seated too deep but hard to tell from the photo. My guess is a combo of a hard primer and possibly a gun that has trigger work done to it with a lighter hammer spring? Again, this is just a guess.
|
No trigger work has been done. It definitley could be an issue with the gun but never before has it misfired with any other ammo. Then i get a half dozen in one box.
Sent from my SM-N920P using Tapatalk
|
05-11-2016, 10:34 AM
|
|
Member
|
|
|
Join Date: Mar 2006
Location: Colorado
Posts: 15,135
Likes: 91,859
Liked 26,393 Times in 8,413 Posts
|
|
Look like pretty hot loads to me.Maybe they've got a source for extra hard primers?
|
05-11-2016, 10:37 AM
|
Member
|
|
|
Join Date: May 2016
Posts: 7
Likes: 0
Liked 0 Times in 0 Posts
|
|
Quote:
Originally Posted by arjay
Look like pretty hot loads to me.Maybe they've got a source for extra hard primers?
|
.44 mag +P 240 grains
Sent from my SM-N920P using Tapatalk
|
05-11-2016, 10:38 AM
|
Member
|
|
|
Join Date: Sep 2014
Location: IA
Posts: 1,728
Likes: 993
Liked 1,627 Times in 800 Posts
|
|
I agree with Ballistic147. The fired round has a flattened primer that has flowed to fill every last bit of the primer pocket. That doesn't happen unless you are at very high pressures. I've never seen that on factory before but I don't shoot Buffalo Bore ammo so maybe it's normal for those
The unfired round has a very light primer strike. That looks like the strike of a free floating firing pin bouncing off a round when chambering. A strike that light probably isn't going to set off any primer.
|
05-11-2016, 10:58 AM
|
Member
|
|
|
Join Date: May 2016
Posts: 7
Likes: 0
Liked 0 Times in 0 Posts
|
|
This is the first issue ive had with misfire. Every other ammo ran through it never missed a beat. But im no gunsmith or expert and it definitley could be an issue with the gun. But the .010 depth primers on some of them leads me to believe its an ammo issue.
Sent from my SM-N920P using Tapatalk
|
05-11-2016, 11:10 AM
|
Member
|
|
|
Join Date: Jun 2012
Location: Demon-class planet
Posts: 7,403
Likes: 29,169
Liked 8,461 Times in 3,772 Posts
|
|
I'd chalk it up to experience and go back to the ammunition that works in your gun. From what you say, that seems to be anything and everything else! Aggravating, I know, but at least nobody has been hurt and your gun is in order.
Kaaskop49
Shield #5103
|
The Following 2 Users Like Post:
|
|
05-11-2016, 11:13 AM
|
Member
|
|
|
Join Date: Jul 2010
Location: Pa.
Posts: 765
Likes: 822
Liked 1,090 Times in 429 Posts
|
|
If I wish to get Super Premium ammunition for that caliber I use Randy Garret. His quality has always been high in my opinion.
|
05-11-2016, 11:40 AM
|
Member
|
|
|
Join Date: May 2016
Posts: 7
Likes: 0
Liked 0 Times in 0 Posts
|
|
Does he have a qebsite
Sent from my SM-N920P using Tapatalk
|
05-11-2016, 12:20 PM
|
Member
|
|
|
Join Date: May 2016
Posts: 7
Likes: 0
Liked 0 Times in 0 Posts
|
|
Does he have a website?
Sent from my SM-N920P using Tapatalk
|
05-11-2016, 12:47 PM
|
|
Member
|
|
|
Join Date: Mar 2016
Location: Murrieta, CA
Posts: 628
Likes: 76
Liked 1,112 Times in 356 Posts
|
|
What are you shooting it out of? Have you checked your strain screw to make sure it isn't backing out?
|
05-11-2016, 01:26 PM
|
|
Member
|
|
|
Join Date: Jun 2015
Location: Mid-Pa aka Pennsytucky
Posts: 183
Likes: 66
Liked 177 Times in 80 Posts
|
|
I believe that BB load is supposed to be a pretty hot load, so I don't think that fired primer being flattened is out of the ordinary. The other primer definitely indicates a very light hit which I wouldn't expect it to fire. Why?? weak mainspring or backed out strain screw is the first place I'd look at.
|
05-11-2016, 01:45 PM
|
Member
|
|
|
Join Date: Apr 2010
Location: Linn Creek MO
Posts: 701
Likes: 1,017
Liked 998 Times in 425 Posts
|
|
Quote:
Originally Posted by Jguzowski
Does he have a website?
Sent from my SM-N920P using Tapatalk
|
Garrett Cartridges Inc. 44 mag .45-70 .44 ammo ammunition bullets african hunting cartridges
Randy Garrett's business is now owned by Ashley Emmerson. The line up of available calibers has expanded quite a bit.
All I can say about your primer depth is that you cannot compare a fired round with one unfired as the primer will set back after ignition.
Heavy recoiling handgun ammo needs the primer set a little bit deeper than "flush".
Dan
|
05-11-2016, 01:49 PM
|
Member
|
|
|
Join Date: May 2016
Posts: 7
Likes: 0
Liked 0 Times in 0 Posts
|
|
Quote:
Originally Posted by BigMuddy
|
I realize that now, i wasnt aware that primers could back out like that after being fired.
Sent from my SM-N920P using Tapatalk
|
05-12-2016, 05:35 PM
|
US Veteran Absent Comrade
|
|
|
Join Date: Mar 2005
Location: Texas
Posts: 20,361
Likes: 24,260
Liked 16,154 Times in 7,408 Posts
|
|
What kind of gun is involved?
|
|
Posting Rules
|
|
|
|
|