Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 03-11-2010, 10:18 AM
clayshooter clayshooter is offline
Member
How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension  
Join Date: Feb 2010
Posts: 16
Likes: 0
Liked 0 Times in 0 Posts
Default How to measure "groove" dimension

I have a 44 Special that I wanted to measure the cast slug dimension from a fired round. The problem is the grooves do not line up directly across from each other. Micrometer measurement at that point is not accurate. Anyone have a trick way to measuring the "across" dimension. Incidentally, the revolver is a S&W 21 dash 4 classic (new gun).
Reply With Quote
  #2  
Old 03-11-2010, 10:32 AM
flat top's Avatar
flat top flat top is offline
Member
 
Join Date: Dec 2008
Posts: 491
Likes: 0
Liked 8 Times in 7 Posts
Default

Clayshooter; You need to "roll" the bullet in the micrometer to obtain the maximum dimension. Also, if you are intending this measurement to get a "true" reading of bore diameter you need to slug the bore....a spent bullet is not a good indicator of true bore dimension for many different reasons.
Reply With Quote
  #3  
Old 03-11-2010, 02:24 PM
5-Shot's Avatar
5-Shot 5-Shot is offline
Member
How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension  
Join Date: Feb 2010
Location: Hills of East Tennessee.
Posts: 1,308
Likes: 2,224
Liked 2,401 Times in 670 Posts
Default

You're not going to believe this! Based on an article by Homer Powley, written many years ago, you need a v-block with the sides of the "v" 36 degrees from horizontal. Lay the slug in the v-block. Measure the distance from the top of the slug to the bottom of the groove. The slug diameter = 0.8944 x that distance. Let me know how it works out.

Ed
Reply With Quote
  #4  
Old 03-11-2010, 09:11 PM
dg101win's Avatar
dg101win dg101win is offline
US Veteran
How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension  
Join Date: Feb 2005
Location: Indiana
Posts: 353
Likes: 233
Liked 135 Times in 45 Posts
Default

I do not recall the math as 5-Shot does. However I recall many,many moons ago an article in American Rifleman about this same thing. All I can recall though is the V-Block and measuring from the top of the bullet to somewhere on the block.
Reply With Quote
  #5  
Old 03-11-2010, 09:15 PM
gregintenn gregintenn is offline
Member
How to measure "groove" dimension  
Join Date: Jan 2008
Location: Lafayette, Tennessee
Posts: 6,926
Likes: 6,833
Liked 8,936 Times in 2,910 Posts
Default

You do have a 36 degree v block don't you?
Reply With Quote
  #6  
Old 03-11-2010, 10:28 PM
Alk8944's Avatar
Alk8944 Alk8944 is offline
Member
How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension  
Join Date: Jan 2007
Location: Sandy Utah
Posts: 8,616
Likes: 1,554
Liked 8,615 Times in 3,452 Posts
Default

Only it is a 108 degree included angle, not 36. This applies to only a 5 groove barrel. There are blocks available for three and seven groove barrels.

The bullet is placed in the V-groove with two lands against the legs of the V. It is then measured from the top land (of the bullet) to the bottom of the V block. This dimension is multiplied by the constant noted above and then this has a second constant, peculiar to that specific block, subtracted from the result for the final solution, the groove-to-groove diameter of the barrel.

And, yes, I do have one, and use it frequently. No, I don't recall where I bought it or I would be glad to tell you.

Last edited by Alk8944; 03-13-2010 at 12:47 AM. Reason: Corrected angle
Reply With Quote
  #7  
Old 03-11-2010, 11:14 PM
gregintenn gregintenn is offline
Member
How to measure "groove" dimension  
Join Date: Jan 2008
Location: Lafayette, Tennessee
Posts: 6,926
Likes: 6,833
Liked 8,936 Times in 2,910 Posts
Default

Wow. That's a specialized tool. Why couldn't you rotate thslug inside your caliper jaws and get an accurate reading?
Reply With Quote
  #8  
Old 03-12-2010, 12:00 PM
clayshooter clayshooter is offline
Member
How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension  
Join Date: Feb 2010
Posts: 16
Likes: 0
Liked 0 Times in 0 Posts
Default how to measure groove dimension

I've tried rotating the slug within the jaws. The way the grooves are orientated I am only able to pick up a small edge of each of the grooves. I'm sure I'm getting a false reading. For a recent 44 special my slug measurement is .424". Should be somewhere around .429"
Reply With Quote
  #9  
Old 03-12-2010, 01:16 PM
NKJ nut's Avatar
NKJ nut NKJ nut is offline
Member
How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension  
Join Date: Aug 2006
Location: Tennessee
Posts: 1,249
Likes: 83
Liked 80 Times in 43 Posts
Default

Quote:
Originally Posted by gregintenn View Post
Wow. That's a specialized tool. Why couldn't you rotate thslug inside your caliper jaws and get an accurate reading?
That works with bores that have an even number of grooves, but when you have a land opposite a groove the measurement is not so easy.
__________________
too TOO young!!
Reply With Quote
  #10  
Old 03-12-2010, 04:28 PM
gregintenn gregintenn is offline
Member
How to measure "groove" dimension  
Join Date: Jan 2008
Location: Lafayette, Tennessee
Posts: 6,926
Likes: 6,833
Liked 8,936 Times in 2,910 Posts
Default

You just ain't spinning it fast enough.
Reply With Quote
  #11  
Old 03-12-2010, 05:18 PM
oldRoger oldRoger is offline
US Veteran
How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension  
Join Date: Nov 2007
Location: Citrus County, Florida
Posts: 2,073
Likes: 21
Liked 218 Times in 110 Posts
Default

Consider that you have two concentric circles the bore and the groove dia.
I have a set of plug/pin gauges which I use to measure the bore, but it can be done at the muzzle with calipers.. I can usually measure from a land across the bore to a groove with my dial calipers; I make this measurement for each land/groove. Average these measurements. You now have bore plus one land. Since you know the bore dimension, subtract it, multiply by two, add the bore dia back and you have the larger concentric circle. You can use a very similar approach with the slug from slugging the barrel.
Is this accurate, well it beats not having any idea.
__________________
Ipsis Rebus Dictantitbus
Reply With Quote
  #12  
Old 03-12-2010, 07:42 PM
NKJ nut's Avatar
NKJ nut NKJ nut is offline
Member
How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension  
Join Date: Aug 2006
Location: Tennessee
Posts: 1,249
Likes: 83
Liked 80 Times in 43 Posts
Default

Quote:
Originally Posted by gregintenn View Post
You just ain't spinning it fast enough.
Dang, now you tell me. I had the slug up to 1,500 rpm and the little needle on the caliber at 300 rpm and still couldn't get a good measurement.
__________________
too TOO young!!
Reply With Quote
  #13  
Old 03-12-2010, 11:35 PM
whelenshooter whelenshooter is offline
SWCA Member
How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension  
Join Date: Feb 2009
Location: Grangeville, Idaho
Posts: 314
Likes: 12
Liked 47 Times in 27 Posts
Wink

Quote:
Originally Posted by NKJ nut View Post
Dang, now you tell me. I had the slug up to 1,500 rpm and the little needle on the caliber at 300 rpm and still couldn't get a good measurement.
You almost had 'er! 1,501 rpm would have done it!
Reply With Quote
  #14  
Old 03-14-2010, 12:11 AM
sonny sonny is offline
Member
How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension  
Join Date: Oct 2005
Location: Florida
Posts: 572
Likes: 0
Liked 8 Times in 8 Posts
Default

I just had this problem a little bit ago.
Take one of your very thin feeler gauges, maybe 0.001" or so. Wrap it around the lead slug and measure it, then subtract TWICE the thickness of feeler gauge. I've done it using several thicknesses of feeler gauges and got the same groove dimension. Yeah, it works well. Just don't try to use a real thick feeler gauge.
Sonny
Reply With Quote
  #15  
Old 03-17-2010, 08:05 PM
Nygma Nygma is offline
Member
How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension How to measure "groove" dimension  
Join Date: Sep 2006
Location: Michigan
Posts: 439
Likes: 18
Liked 35 Times in 18 Posts
Default

A V-anvil micrometer is the easiest way. They are expensive when bought new, but can be had for a reasonable price used. I bought a lighty used one at a machinery auction about ten years ago for $40.

They are for sale on eBay. Search Mitutoyo 114-202

Last edited by Nygma; 03-17-2010 at 08:10 PM.
Reply With Quote
Reply

Tags
micrometer, rifleman

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Ahrend Retro "K-L" Moradillo Finger Groove raylan007 Accessories/Misc - For Sale or Trade 1 12-22-2015 06:25 PM
i need a tape measure with 4/5" measurements speedyquad The Lounge 38 07-26-2014 02:42 PM
"SOLD" Hornady New Dimension 3 Die Set- Titanium Nitride for 44 SPL/ 44 Magnum D.O.A.F.S. Accessories/Misc - For Sale or Trade 0 03-26-2014 07:40 AM
WTB--Finger Groove "Combat" Grips for K 03gringo WANTED to Buy 1 11-23-2009 11:23 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 01:27 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)