Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 03-19-2010, 10:28 AM
Lou_NC Lou_NC is offline
Member
 
Join Date: Jan 2007
Location: Raleigh, NC
Posts: 564
Likes: 102
Liked 398 Times in 162 Posts
Default Midway Rainier plated bullets vs. jacketed?

Folks,

I'm an experienced reloader, but I am new to the concept of "plated" bullets. I'm wondering what load data to use with these bullets?

Are thuey basically hard cast lead with a copper "wash" coating that will perform essentially like cast bullets in the bore, or is the plating thicker, such that the bullets perform more like jacketed in the bore?

I'm also curious about leading. Again, if the "plating" is superficial, do these bullets potentially lead the bore similarly to cast bullets (depending on hardness and velocity along with other factors), or are they completley impervious to leading the bore, like jacketed bullets are?

Thanks,
Lou
__________________
NRA Certified Instructor & RSO
Reply With Quote
  #2  
Old 03-19-2010, 10:41 AM
Dragon88 Dragon88 is offline
Member
Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed?  
Join Date: Dec 2009
Location: North Carolina
Posts: 3,054
Likes: 107
Liked 456 Times in 205 Posts
Default

Some say to use cast bullet data, others jacketed. I personally use jacketed data with good success. While these bullets are soft, they are also usually .001" larger in diameter just like cast, and they generate about the same pressure and velocity in my guns as jacketed. The plating is very thin, so do not push them to max velocities. Nothing over 1100-1200. With moderate loads the plating will stay intact until the bullet exits and give zero leading. Oh, also, go light on the crimp to avoid damaging the plating.

Loaded right these make excellent and cheap plinking bullets.
Reply With Quote
The Following User Likes This Post:
  #3  
Old 03-19-2010, 12:39 PM
TSQUARED TSQUARED is offline
Member
Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed?  
Join Date: Nov 2004
Location: Michigan, USA
Posts: 2,260
Likes: 2
Liked 114 Times in 84 Posts
Default

The Berry's and Rainier plated bullets have a fairly thin copper plating over a swaged soft lead core. I have not found them to be as accurate as either lead or jacketed bullets for bulleye psitol standrads. They are however very suitable for the action pistol games out to 25 yards. In terms of cost - one can purchase jacketed bullets (Zero, Montana Gold) for equal or lesser prices than the plated.
Frontier offers two types of plated bullets one over swages soft lead cores and the other over a hard cast core - I have not tried these bullets but they are popular with many action pistol shooters and are less expensive than jacketed.
In terms of velocity I keep my plated bullet loads to 900 fps or lower. At one time Rainier published data for their bullets. One caution with reloading plated bulets is to insure that during crimping you do not cut through the plating.
I am away for the winter and will return in May. Send me an e-mail in May and I'll send you the published Rainier data.
Reply With Quote
  #4  
Old 03-19-2010, 02:00 PM
Skip Sackett Skip Sackett is offline
Banned
Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed?  
Join Date: Mar 2006
Location: Hoosier Land!
Posts: 4,379
Likes: 587
Liked 576 Times in 307 Posts
Default

On Ranier's website they explicitly say to use lead data and keep the velocity less than magnum ones.

I have had good success with both Ranier and Berry plated bullets. I use lead data and don't drive them over 900fps.

Hope this helps.
Reply With Quote
  #5  
Old 03-19-2010, 02:36 PM
1066 1066 is offline
US Veteran
Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed?  
Join Date: Aug 2005
Location: Albuquerque
Posts: 151
Likes: 0
Liked 2 Times in 2 Posts
Default

I have not experienced a problem with leading with either the Ranier or the Berry plated bullets. Both shoot very clean, but I load to relatively low velocity.

Personally, I have had better luck with Berry bullets; I always use the "double struck" and they are just as accurate as lead in most of my guns.

The low velocity is the only downside, Berry says 1200fps and Ranier says no more then 1200-1250 fps. For high speed loads I generally use Hornady bullets.

I generally use the Hornady load date for a lead bullet of the same weight and have had excellent results.
Reply With Quote
  #6  
Old 03-19-2010, 02:48 PM
Revolver-time Revolver-time is offline
Member
Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed?  
Join Date: Nov 2007
Location: Savannah, Ga.
Posts: 412
Likes: 30
Liked 109 Times in 54 Posts
Default

I use the Ranier bullets in just about everything I shoot. I keep my loads at or below 1000fps and have had zero problems and good accuracy results.
Reply With Quote
  #7  
Old 03-19-2010, 02:56 PM
handgunner356 handgunner356 is offline
Member
Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed?  
Join Date: Dec 2003
Location: SE Iowa on the Mississipp
Posts: 3,137
Likes: 1
Liked 352 Times in 230 Posts
Default

I've used both the Rainiers and Berrys in 9, 38/357, 40, 44 and 45 with good results. I find them to usually be priced a little less than jacketed rounds. Almost always find they need a tenth or two more powder to match the same velocity as lead rounds. In .40 180gr lead I use 5.0grs Universal and need 5.2grs to match the same velocity with the plated bullets. The thing to watch on the crimp is that you don't cut through the plating causing it to peel when fired.
Reply With Quote
  #8  
Old 03-19-2010, 03:36 PM
whelenshooter whelenshooter is offline
SWCA Member
Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed?  
Join Date: Feb 2009
Location: Grangeville, Idaho
Posts: 314
Likes: 12
Liked 47 Times in 27 Posts
Default

Other people have asked the same question. You can go here to see lot of good information: rainier bullets;

In a nutshell, what I know is that you should use jacketed bullet data that will give you velocities below 1,200 fps rather than lead bullet data. Though Rainier and Berry's plated bullets are softer than jacketed bullets, they have a higher coefficient of friction and you can stick a bullet in the barrel if you use lead bullet info that is too light. Do not overcrimp Rainier and Berry's plated bullets . They usually don't have a crimp groove and if you put too heavy of a roll crimp on them you may crack the plating and part may stick in your barrel. If you use a roll crimp die, just set it enough to remove the belling you did so you could seat the bullets. I purchased taper crimp dies from Redding for the revolver cartridges in which I use the plated bullets. For .45 Colt loads with plated bullets I use my taper crimp die for .45 ACP. Of course you have to back the die way off and adjust it accordingly, but it works well. I really like Rainier and Berry's plated bullets! I find them more than accurate enough for my purposes, much cheaper than jacketed bullets, and cleaner to both load and shoot than cast bullets. (With cast bullets you will often get a buildup of bullet lube in your dies that occasionally needs to be cleaned out.)

Have at 'em and have fun!
Reply With Quote
  #9  
Old 03-19-2010, 05:42 PM
johngalt's Avatar
johngalt johngalt is offline
Member
Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed?  
Join Date: Feb 2007
Location: St. Paul (smokey!) MN
Posts: 5,335
Likes: 1,443
Liked 6,647 Times in 2,564 Posts
Default

I tried Rainier .45 230 gr round nose bullets back when I first started loading. I had both the rainier and regular FMJ.

I was having setback problems with the rainier, but the FMJ were fine. I never figured out why, but I suspect they were .451 (like jacketed) instead of .452 (like lead), and were thus slightly undersized.

After my problems I quit using them, I don't have such issues with regular lead and jacketed bullets.
__________________
Common sense isn't so common.
Reply With Quote
  #10  
Old 03-19-2010, 07:36 PM
Skip Sackett Skip Sackett is offline
Banned
Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed? Midway Rainier plated bullets vs. jacketed?  
Join Date: Mar 2006
Location: Hoosier Land!
Posts: 4,379
Likes: 587
Liked 576 Times in 307 Posts
Default



Ranier on the left and Berry on the right. Taper crimp and no damage to the plating. Also, no bullet setback.

Hope this helps.
Reply With Quote
Reply

Tags
colt, crimp, hornady, smith-wessonforum.com, universal

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Plated vs. Jacketed Bullets Mike1161 Smith & Wesson M&P Pistols 16 11-05-2013 09:06 PM
.500 diameter jacketed\plated bullets 600\700 gr hunteratheart WANTED to Buy 1 06-28-2013 08:30 AM
Rainier vs Berry's Plated Bullets Kevin G Reloading 15 05-13-2013 09:30 AM
Buying Jacketed And Plated Bullets In Bulk Nick B Reloading 16 03-09-2012 12:43 AM
Rainier plated .357 and Win. 231 dma1 Reloading 10 03-08-2012 03:32 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 04:10 PM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)