|
|
07-07-2010, 02:32 PM
|
Member
|
|
|
Join Date: Jul 2007
Location: Prescott, AZ
Posts: 69
Likes: 2
Liked 15 Times in 7 Posts
|
|
Reloading with .357 vs. .38 Special cases
I recently purchased a revolver that can shoot .38 Special and .357 Magnum rounds and have brass for each. I am considering using .357 Magnum cases to reload for this gun vs. .38 Special cases in order to keep the cylinder cleaner. Is there any merit to this approach, or will using .38 Special cases be fine?
|
07-07-2010, 02:42 PM
|
Member
|
|
|
Join Date: Dec 2009
Location: North Carolina
Posts: 3,054
Likes: 107
Liked 456 Times in 205 Posts
|
|
Shooting .38s in a 357 revolver is no problem, many have been doing it for a long time. Just clean your revolver well after shooting. Since you have 357 brass available though, I would load and shoot those. There's no reason not to. You can do anything from light plinking loads to full bore hunting loads in the 357 case.
Just be careful not to use 38 data in the 357 case, you can get a load that's too light that way and end up with a BIB or other bad stuff. Always consult good data for the proper cartridge.
|
07-07-2010, 02:46 PM
|
|
Moderator
|
|
|
Join Date: May 2006
Location: N.AZ
Posts: 3,874
Likes: 614
Liked 2,399 Times in 595 Posts
|
|
I think that would be the only reason not to use .38Spl brass but, it still going to get dirty, especially if you are shooting lead.
I use to load my target loads in .357Mag brass because they produced tighter groups (less travel before contacting forcing cone??) but stopped doing that.
I use the .38Spl brass for my plinker loads and save the .357Mag brass for my magnum loads
|
07-07-2010, 03:31 PM
|
|
SWCA Member
|
|
|
Join Date: Dec 2008
Posts: 6,898
Likes: 736
Liked 1,211 Times in 740 Posts
|
|
or simply use a chamber brush to clean the cylinder...it fits tighter then the bore brush and will remove the deposit
__________________
SWCA#2208
KK4EMO
|
07-07-2010, 04:11 PM
|
Banned
|
|
|
Join Date: Mar 2006
Location: Hoosier Land!
Posts: 4,379
Likes: 587
Liked 576 Times in 307 Posts
|
|
Using 38spl cases isn't a problem. There will be a carbon ring that needs to be removed from the cylinder before 357Mag loads can be run in it though. This can be done with a spent 357Mag case. Simply flare the mouth, just a smidgen, and push it into the chamber with cleaning solvent added.
The will come right out.
Hope this helps.
|
07-07-2010, 05:49 PM
|
|
US Veteran
|
|
|
Join Date: Dec 2005
Location: Birmingham, Alabama
Posts: 4,483
Likes: 228
Liked 2,398 Times in 1,082 Posts
|
|
I have used both, and currently only load .38 brass since I have a ton of it. I load on a progressive press and it's too much trouble to me to change the dies. I don't have enough .357 brass to make a 500-1000 round production run. If you load some hot loads in .38, be sure they are adequately marked so they don't find their way into a gun not appropriately rated. I color code primers with a magic marker. When the primer is gone, so is the mark.
|
07-07-2010, 05:59 PM
|
|
Moderator SWCA Member Absent Comrade
|
|
|
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
|
|
I was going to suggest carrying a spent .357 Magnum case to remove the carbon ring from the cylinders if you decided you wanted to shoot magnum ammo after .38 Special ammo but Skip already did that. Like the others said, there's no reason not to shoot target ammo in .38 Special brass in your magnum. A bore brush easily removes any leftovers in the cylinder. Finding .38 Special brass is easier and cheaper than magnum brass. I would save the .357 magnum brass for magnum loads.
__________________
Freedom is never free!!
SWCA #3437
|
07-07-2010, 06:57 PM
|
|
US Veteran
|
|
|
Join Date: Aug 2004
Location: Rusk Co. Texas
Posts: 1,318
Likes: 0
Liked 43 Times in 31 Posts
|
|
If you have a "short cylinder", like the M28 or M27, using .38 Special brass can gain some space for a longer bullet without having to seat it real deep. I do that with some 358429s and realize that bullet is for .357 use, even though it's in .38 Special brass. It's about 150 fps slower than using .357 brass and seating deep, but 1270 fps MV with a 170 gr bullet is usually sufficient for anything around here that needs shooting.
|
07-09-2010, 07:17 PM
|
Member
|
|
|
Join Date: Feb 2010
Location: Florida
Posts: 1,338
Likes: 65
Liked 247 Times in 166 Posts
|
|
I have plenty of both and just use .357 brass. Only a few dollars difference in price from starline, like $64/500 shipped. My .38 brass just sits. I don't see much reason to use a case shorter than what the gun was designed to accept. I guess you could use a little less powder in the .38 case. Seems a bit more accurate in the longer case, plenty of people will argue the other point, but try it and see for yourself.
|
07-09-2010, 08:00 PM
|
Member
|
|
|
Join Date: May 2006
Posts: 44
Likes: 0
Liked 0 Times in 0 Posts
|
|
You can't go wrong using .357 cases, unless you use look-alike components for target and magnum loads and then mix them up. No carbon ring worries and no chance that any of your full-house .357 loads could be inadvertently loaded into some poor, innocent .38 Special. Loading full charge .357's into .357 cases and loading target /plinking loads into .38 cases is an excellent idea, so long as you are religious about cleaning up after shooting the .38's. If you are at all lax about cleanup, then why risk the issue?
|
|
Posting Rules
|
|
|
|
|