|
|
09-10-2010, 01:05 PM
|
Member
|
|
|
Join Date: Sep 2009
Location: New York
Posts: 156
Likes: 1,207
Liked 19 Times in 14 Posts
|
|
Reloading .38 S&W
I'm considering buying an S&W Terrier and started looking into reloading for it. Buying brass is no problem but I have a question about bullets. One source indicates bullets should be .359, which I haven't been able to find. Does anyone have experience reloading for this caliber and know if .357 or .358 bullets are okay?
Thanks.
|
09-10-2010, 02:24 PM
|
Member
|
|
|
Join Date: Feb 2007
Location: SW MT
Posts: 6,734
Likes: 10,507
Liked 6,028 Times in 2,968 Posts
|
|
You are going to have to measure your bore and cylinder throats. Slugging them with a soft lead sinker is the best way, then mike the results. Most 38S&W I am aware of need a .360 cast bullet. Without a large enough bullet you are cleaning lead out the bbl often.
__________________
Front sight and squeeze
|
09-10-2010, 03:17 PM
|
|
Member
|
|
|
Join Date: Nov 2005
Location: Florida
Posts: 684
Likes: 59
Liked 374 Times in 121 Posts
|
|
I shoot generic .358 diameter cast & swaged bullets in both several 33-1s, Colt PPs and a Webley.
Several custom casters offer .359 & .360 diameter lead bullets. Tried some at .360 but found they were no better in my guns than the .358 size.
All shoot quite accurately in my guns. Get a bit of leading in the Webley that seems to have the largest bore & throat diameter. The Colts and Smiths seem to do just fine.
Typically load 2.9 grains 231 or 3.0 grains of Unique. Both produce about 725 - 750 fps depending on gun & barrel length.
|
09-10-2010, 09:46 PM
|
|
Member
|
|
|
Join Date: Mar 2009
Location: central pa
Posts: 5,336
Likes: 2,745
Liked 2,492 Times in 1,182 Posts
|
|
I have fair result's useing lead .358's. Missouri Bullet Company offer's .360 dia bullet's at a good price. Missouri Bullet Company
__________________
Stay safe people!
|
09-11-2010, 12:22 AM
|
SWCA Member Absent Comrade
|
|
|
Join Date: Nov 2002
Location: SLC, Utah
Posts: 5,060
Likes: 739
Liked 3,275 Times in 1,282 Posts
|
|
Mine shoot well with Speer's swaged lead bullets, which are sized to .358". I use fairly fast powders, either Bullseye or Unique. They must bump up in size a bit because they shoot just fine.
Try some .358" bullets before you go nuts looking for .360's. They should make you happy.
|
09-11-2010, 06:20 PM
|
|
Moderator SWCA Member Absent Comrade
|
|
|
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
|
|
Most 38 S&W revolvers will not shoot .358 bullets well. The accuracy is usually terrible. Like said above, it's worth a try but I've found it's best to shoot a .360 bullet. If you can find them it's a hoot to shoot a 200gr bullet to replicate the old British 38/200 load.
__________________
Freedom is never free!!
SWCA #3437
|
09-12-2010, 12:31 AM
|
Member
|
|
|
Join Date: Sep 2010
Location: Ridgecrest, CA USA
Posts: 13
Likes: 1
Liked 0 Times in 0 Posts
|
|
ArcAngel--
I think I'd restrict the British service loads to the S&W M&P or Webley-Enfield revolvers they were intended for. A S&W Terrier or Colt Police Positive might be strained by a 200 grain bullet at 700-725 FPS.
I don't have a Terrier, but do have a Colt PP x 4"--and it dotes on Lyman #358477 (150 grain SWC) at 700-725 FPS. These shoot right to the sights at 25 yards.
|
09-12-2010, 07:30 PM
|
|
Moderator SWCA Member Absent Comrade
|
|
|
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
|
|
Come to think of it, you are correct. Those 38/200 loads aren't for every 38 S&W revolver. I do usually load a 160gr .360" bullet for most of my 38 S&W ammo. That weight bullet isn't too much heavier than the commercial 145/146gr load now being made.
__________________
Freedom is never free!!
SWCA #3437
|
09-13-2010, 01:54 PM
|
Member
|
|
|
Join Date: Sep 2009
Location: New York
Posts: 156
Likes: 1,207
Liked 19 Times in 14 Posts
|
|
Thanks everyone for all the information.
|
|
Posting Rules
|
|
|
|
|