Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 10-04-2010, 08:31 PM
Zackary Zackary is offline
Member
Brinell numbers-how important ?  
Join Date: Nov 2006
Posts: 119
Likes: 2
Liked 139 Times in 29 Posts
Default Brinell numbers-how important ?

I'd like to begin loading .357 mag ammo to target shoot in my S&W 28-2, 6" and my Speed Six , 4" Ruger. I'm currently loading 38 spl rounds using LSWC, 158 grain,Brinell 12, 4.0 grains W231. Do I need to move to 158 grain LSWC , Brinell 18, or will the 12's work? I want to get used to the added recoil in both weapons, true accuracy to follow. I'm also not sure the W 231 is up to the task at mag velocities. Your time and expertise are greatly appreciated. Thank you.
Reply With Quote
  #2  
Old 10-04-2010, 08:50 PM
Skip Sackett Skip Sackett is offline
Banned
Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ?  
Join Date: Mar 2006
Location: Hoosier Land!
Posts: 4,379
Likes: 587
Liked 576 Times in 307 Posts
Default

Zach,
Are you purchasing bullets now?

If you are, just add some lead free solder to the mix or Linotype. About 2 to 5% to start. I think that BHN is less important, within reason that is, than fit. If the fit is right, the harness of the bullet only comes into play if it is too soft for the load.

@ 12BHN and W231, that may come quicker than say, 12BHN and AA#7 or #9. The pressure is less with those powders although the velocity will be more. What I would do is try a few in my firearms and go from there.

I have found in almost all of my firearms that 12BHN to 18BHN will get the job done all the way up to 2000fps from my rifles. Minimal lead flakes at those velocities, no streaking.

Hope this helps!

Have fun and be safe!
Reply With Quote
  #3  
Old 10-04-2010, 09:15 PM
epj's Avatar
epj epj is offline
US Veteran
Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ?  
Join Date: Dec 2005
Location: Birmingham, Alabama
Posts: 4,481
Likes: 227
Liked 2,397 Times in 1,081 Posts
Default

Proper bullet sizing is more critical than hardness. A bullet too small will allow gas to leak past the bullet base and this will cause leading in a big way. Bullets can be too hard also, but this shouldn't be an issue with magnum pressure.
Reply With Quote
  #4  
Old 10-05-2010, 09:28 PM
michael thornton's Avatar
michael thornton michael thornton is offline
Member
 
Join Date: May 2004
Location: NORTH ALABAMA
Posts: 1,713
Likes: 186
Liked 83 Times in 51 Posts
Default

im casting wheal weights shout i add anything? most of my loads are mild 38 357 45 acp
__________________
WILL WORK FOR AMMO!
Reply With Quote
  #5  
Old 10-05-2010, 10:16 PM
epj's Avatar
epj epj is offline
US Veteran
Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ?  
Join Date: Dec 2005
Location: Birmingham, Alabama
Posts: 4,481
Likes: 227
Liked 2,397 Times in 1,081 Posts
Default

Quote:
Originally Posted by michael thornton View Post
im casting wheal weights shout i add anything? most of my loads are mild 38 357 45 acp
WW alloy is fine as is. If you want to harden the bullets a bit more to insure good feeding in the ACP, just water drop vs air cooling. I water drop everything as a matter of convenience.
Reply With Quote
  #6  
Old 10-06-2010, 12:25 AM
Rule3's Avatar
Rule3 Rule3 is offline
Member
Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ?  
Join Date: Feb 2008
Location: Florida
Posts: 22,065
Likes: 10,777
Liked 15,467 Times in 6,788 Posts
Default

Quote:
Originally Posted by Zackary View Post
I'd like to begin loading .357 mag ammo to target shoot in my S&W 28-2, 6" and my Speed Six , 4" Ruger. I'm currently loading 38 spl rounds using LSWC, 158 grain,Brinell 12, 4.0 grains W231. Do I need to move to 158 grain LSWC , Brinell 18, or will the 12's work? I want to get used to the added recoil in both weapons, true accuracy to follow. I'm also not sure the W 231 is up to the task at mag velocities. Your time and expertise are greatly appreciated. Thank you.

I think the BHN of 12 is fine at 38spl velocities. The harder BHN of 18 is better at Magnum speeds. But as mentioned proper fit is probably most important.

I use a lot of Missouri Bullets and one of the best explanations is posted on their web site. I have asked them for a softer 230gr LRN in 45 ACP. at the target velocities I shoot at, I think 18 is too hard. I would like to try 12. It made no sense to me that the 45 ACP was the same hardness as full 357 or 44 Magnum loads.

Missouri Bullet Company
__________________
Still Running Against the Wind
Reply With Quote
  #7  
Old 10-06-2010, 01:21 AM
BruceM's Avatar
BruceM BruceM is offline
Member
Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ?  
Join Date: Oct 2003
Location: Southeast Wisconsin
Posts: 1,750
Likes: 7
Liked 657 Times in 369 Posts
Default

If bullets are water dropped, they should be of the needed diameter as cast because reducing their size with a sizing die any more than .001" at the absolute maximum will destroy the hardness of the driving bands. Obviously, extreme care must be used when working with water while casting. I prefer the oven method of heat treating although it is more of a bother.

I don't believe that a bullet can be too hard but it can be harder than needed. As the bullet gets harder, size becomes more critical but you cannot make up for any more than very minor size issues by messing around with alloy hardness.

W231 is not a good choice for magnum level cast bullet loads. You will want to use a much slower propellant such as 2400, H110/W296 or AA#9.

"It made no sense to me that the 45 ACP was the same hardness as full 357 or 44 Magnum loads."

It's not to prevent leading but to bypass any possible feeding issues in the bottom feeder caused by too soft an alloy.



Bruce

Last edited by BruceM; 10-06-2010 at 01:28 AM.
Reply With Quote
  #8  
Old 10-06-2010, 06:15 AM
Skip Sackett Skip Sackett is offline
Banned
Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ?  
Join Date: Mar 2006
Location: Hoosier Land!
Posts: 4,379
Likes: 587
Liked 576 Times in 307 Posts
Exclamation Bruce is the man!

Quote:
Originally Posted by BruceM View Post
I don't believe that a bullet can be too hard but it can be harder than needed. As the bullet gets harder, size becomes more critical but you cannot make up for any more than very minor size issues by messing around with alloy hardness.

"It made no sense to me that the 45 ACP was the same hardness as full 357 or 44 Magnum loads."

It's not to prevent leading but to bypass any possible feeding issues in the bottom feeder caused by too soft an alloy.



Bruce
I water drop too but selectively. Wheel weights are of sufficient hardness for the 45ACP loads and firearms I cast for. I have had some bullets that were too soft though and had the problems that Bruce alludes to in a 1911. It will really show up in H&G #68 bullets if they are too soft.

If you cast and are having feeding problems add a little Linotype or Tin or water drop your bullets and see if the problem doesn't go away.
Reply With Quote
  #9  
Old 10-06-2010, 07:34 AM
epj's Avatar
epj epj is offline
US Veteran
Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ?  
Join Date: Dec 2005
Location: Birmingham, Alabama
Posts: 4,481
Likes: 227
Liked 2,397 Times in 1,081 Posts
Default

Ditto what Skip said
Reply With Quote
  #10  
Old 10-06-2010, 10:35 AM
Rule3's Avatar
Rule3 Rule3 is offline
Member
Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ?  
Join Date: Feb 2008
Location: Florida
Posts: 22,065
Likes: 10,777
Liked 15,467 Times in 6,788 Posts
Default

How did the OP's thread turn into a casting thread???

He was asking about bullet hardness for 38 special.
__________________
Still Running Against the Wind
Reply With Quote
  #11  
Old 10-07-2010, 12:03 PM
ArchAngelCD's Avatar
ArchAngelCD ArchAngelCD is offline
Moderator
SWCA Member
Absent Comrade
Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ?  
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
Default

Just remember, shooting a hard bullet too slow will probably cause more leading than shooting a soft bullet too fast.
__________________
Freedom is never free!!
SWCA #3437
Reply With Quote
  #12  
Old 10-07-2010, 12:27 PM
Skip Sackett Skip Sackett is offline
Banned
Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ?  
Join Date: Mar 2006
Location: Hoosier Land!
Posts: 4,379
Likes: 587
Liked 576 Times in 307 Posts
Exclamation Well, kinda.

Quote:
Originally Posted by ArchAngelCD View Post
Just remember, shooting a hard bullet too slow will probably cause more leading than shooting a soft bullet too fast.
Tony is right to a certain extent on this point. The only thing I would add to his statement is that the bullet has to be too small for the bore too.

If it doesn't fit, hardness is a moot point. If it is too small and hard, and you don't drive it hard, you are going to have some real leading problems.

At least that has been my experience. For the most part, 12BHN and the right size will do wonderful things at 1100fps or less. If you want to push them harder, then, I have cast as hard as 22BHN. Remember, harder bullets from the same mould are going to be: #1 lighter, #2 bigger.
Reply With Quote
  #13  
Old 10-08-2010, 01:08 AM
ArchAngelCD's Avatar
ArchAngelCD ArchAngelCD is offline
Moderator
SWCA Member
Absent Comrade
Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ? Brinell numbers-how important ?  
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
Default

Skip is also correct. If the bullets are too small the hot gasses will not be sealed causing leading. It's the same effect as using too hard a bullet for light pressure rounds. Neither will seal in the barrel.
__________________
Freedom is never free!!
SWCA #3437
Reply With Quote
Reply

Tags
1911, 38spl, 44 magnum, 45acp, ruger

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Brinell hardness and MBC Mikeinkaty Reloading 3 01-22-2017 06:02 AM
Brinell 16 verses Brinell 18? rde1911 Reloading 24 08-25-2014 02:23 AM
Brinell Hardness pipeliner Reloading 5 04-09-2013 06:57 PM
Brinell hardness for 9mm bullets 1sailor Reloading 11 06-24-2012 08:40 PM
brinell hardness of 15; how fast can it go? joedaddy Reloading 16 08-19-2011 12:02 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 04:23 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)