|
|
11-16-2010, 11:43 PM
|
|
US Veteran Absent Comrade
|
|
|
Join Date: Feb 2003
Location: South Central Tennessee
Posts: 1,438
Likes: 0
Liked 84 Times in 17 Posts
|
|
New To Reloading
The UPS left a nice package for me today, my reloading equipment and other reloading goodies. I now have to find the right place to get started, and may have to build a special bench to do it. What is your mode of reloading, sanding or sitting? Sitting sims a bit awkward when moving that lever, I think standing would most likely work best. If your preference is standing, what should the bench height be, in relation to the body, waist-high? Thanks.
Pete
|
11-17-2010, 12:20 AM
|
Member
|
|
|
Join Date: Oct 2009
Location: Washington State
Posts: 116
Likes: 1
Liked 7 Times in 6 Posts
|
|
Most seem to prefer standing. The sitters I know seem to like a bar stool. It is generally easier to work on the press while standing and not "hunched over".
For height, it really depends on the press. As a general rule, the handle of the press should be at about shoulder height when it is in its uppermost position. If you are really going to crank the rounds out you should definitely pay attention to the ergonomics.
Bob
|
11-17-2010, 12:58 AM
|
Member
|
|
|
Join Date: May 2008
Location: Aurora, CO
Posts: 20
Likes: 0
Liked 1 Time in 1 Post
|
|
I use a high stool, no back.
Jason
|
11-17-2010, 01:36 AM
|
|
Member
|
|
|
Join Date: Nov 2004
Location: Mountain State
Posts: 3,569
Likes: 56
Liked 379 Times in 149 Posts
|
|
Go set it on the counter top in the kitchen and see if it is about right Pete. Then adjust from there .
|
11-17-2010, 07:43 AM
|
|
Member
|
|
|
Join Date: Mar 2008
Location: WI
Posts: 602
Likes: 16
Liked 112 Times in 66 Posts
|
|
I usually do some case prep,priming, & powder charging while standing. I use the press while sitting. It all depends on how you want to set up.
|
11-17-2010, 08:42 AM
|
Member
|
|
|
Join Date: Nov 2008
Location: Upstate, S.C.
Posts: 1,155
Likes: 78
Liked 220 Times in 133 Posts
|
|
I would agree with Bulleye Smith about the hieght of the bench. I built a dedicated bench (it does get used for a few other projects in the garage). I set my bench up with inserts/bolts so that I can remove the press and powder stand and have a open work surface. Seated vs. standing? I do both. But I do use a stool instead of a chair, so I'm almost standing anyway.
|
11-17-2010, 10:00 AM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,065
Likes: 10,777
Liked 15,467 Times in 6,788 Posts
|
|
My bench is semi portable and low so I sit on a folding chair. Plus I am lazy.
I sent you a PM with a link to another forum that has benches. Only 586,000 views!
__________________
Still Running Against the Wind
|
11-17-2010, 11:11 AM
|
|
Member
|
|
|
Join Date: Jul 2010
Location: Florida
Posts: 6,556
Likes: 3,344
Liked 9,154 Times in 3,433 Posts
|
|
How long are you willing to stand up? I sit; I'm gonna be there for a while. Set your equipment up at whatever height is comfortable for you.
|
11-17-2010, 11:37 AM
|
Member
|
|
|
Join Date: Sep 2008
Location: Central NC
Posts: 583
Likes: 24
Liked 37 Times in 18 Posts
|
|
Quote:
Originally Posted by SMSgt
How long are you willing to stand up? I sit; I'm gonna be there for a while. Set your equipment up at whatever height is comfortable for you.
|
+1
I spend hours at my bench so I sit. I found an old office desk with a heavy laminate top for my bench and I use an office chair with an adjustable height to sit in.
__________________
Andy
|
11-17-2010, 01:02 PM
|
|
US Veteran Absent Comrade
|
|
|
Join Date: Feb 2003
Location: South Central Tennessee
Posts: 1,438
Likes: 0
Liked 84 Times in 17 Posts
|
|
Great responses, great ideas... after seeing the pictures Roy referenced, I'd say that some folks are really into it, big time. My reloading is going to be minimal, as I no longer do much shooting. I decided to start reloading mostly as a stress-releaser project, or something to do during the winter months. Thanks a bunch fellers.
Pete
|
11-17-2010, 02:59 PM
|
|
Member
|
|
|
Join Date: Feb 2009
Location: god bless the USA
Posts: 661
Likes: 75
Liked 149 Times in 61 Posts
|
|
Quote:
Originally Posted by OCD1
My bench is semi portable and low so I sit on a folding chair. Plus I am lazy.
I sent you a PM with a link to another forum that has benches. Only 586,000 views!
|
Hey how 'bout posting that link!
/c
|
11-17-2010, 03:12 PM
|
|
US Veteran Absent Comrade
|
|
|
Join Date: Feb 2003
Location: South Central Tennessee
Posts: 1,438
Likes: 0
Liked 84 Times in 17 Posts
|
|
|
11-17-2010, 03:42 PM
|
|
Member
|
|
|
Join Date: May 2009
Location: Southern Maine
Posts: 13,611
Likes: 491
Liked 1,883 Times in 987 Posts
|
|
Quote:
Originally Posted by oldfella
Great responses, great ideas... after seeing the pictures Roy referenced, I'd say that some folks are really into it, big time. My reloading is going to be minimal, as I no longer do much shooting. I decided to start reloading mostly as a stress-releaser project, or something to do during the winter months. Thanks a bunch fellers.
Pete
|
I am in about the same boat Pete. Have all my stuff, and even picked up a clearance 6' section of laminate countertop from HD. Just have to get my bench together, and have been trying to decide myself if I want to sit or stand, and what height will work best. I have Rhuematoid Arthritis, so I don't think standing will be an option, but then again I don't plan on reloading hours on end, as I don't shoot a whole heck of alot of ammo. Decided to start reloading due to the price of ammo, my fear of .45acp availability next year on the centennial of the 1911, and mainly for something to do during the winter months.
|
11-17-2010, 03:51 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,065
Likes: 10,777
Liked 15,467 Times in 6,788 Posts
|
|
Quote:
Originally Posted by Chuck Jones
Hey how 'bout posting that link!
/c
|
I did not want to get in trouble for linking to another gun forum
Maybe they will not make oldfella sit in the corner.
__________________
Still Running Against the Wind
|
11-17-2010, 03:54 PM
|
|
US Veteran Absent Comrade
|
|
|
Join Date: Feb 2003
Location: South Central Tennessee
Posts: 1,438
Likes: 0
Liked 84 Times in 17 Posts
|
|
Oops...Sorry Lee
Pete
|
11-17-2010, 08:11 PM
|
|
US Veteran Absent Comrade
|
|
|
Join Date: Feb 2003
Location: South Central Tennessee
Posts: 1,438
Likes: 0
Liked 84 Times in 17 Posts
|
|
Here is another interesting idea, a bit labor-intensive, but worth considering:
Reloading Bench Project
Pete
|
11-17-2010, 08:57 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,065
Likes: 10,777
Liked 15,467 Times in 6,788 Posts
|
|
Here is a simple, pimple "kit" just by some 2 x4's and plywood It is sold at other places but just happened to see this in a catalog.
By the lumber at Lowes or Homers and have them cut it and presto, you have a bench.
2x4 Basics® Bench Kit, Tools & Accessories, Reloading, Shooting : Cabelas.com
__________________
Still Running Against the Wind
|
11-17-2010, 09:08 PM
|
|
US Veteran Absent Comrade
|
|
|
Join Date: Feb 2003
Location: South Central Tennessee
Posts: 1,438
Likes: 0
Liked 84 Times in 17 Posts
|
|
With some modifications this workbench will do just fine:
Building A Basic Work Bench
Pete
|
11-17-2010, 09:11 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,065
Likes: 10,777
Liked 15,467 Times in 6,788 Posts
|
|
That's pretty much my garage bench I built long ago only I used 3/4 plywood. You need to be careful to leave enough edge to put bolts through to hold the press or you will need very long ones to go through the 2x4 frame or end up lag bolting them in.
__________________
Still Running Against the Wind
|
11-17-2010, 11:50 PM
|
Member
|
|
|
Join Date: Jul 2008
Location: Las Vegas, NV
Posts: 3,428
Likes: 5,932
Liked 5,259 Times in 1,732 Posts
|
|
Pete: It is really a back-stress reliever if you build your reloading bench for the correct height to for the standing position and then find an old bar stool and cut it to the correct height to allow you to on occasion sit at your press when the mood hits you. I have built several benches over the years and hit on using 1 1/8" thick plywood for the top. This plywood is known to the trade as "2-4-1" ply. It is sturdy enough to allow really heavy duty presses and the resulting 'leverage' that they require. For your light duty requirements the use of lag bolts down thru the top into the 2X4 purlins will work fine. If you can't find any '2-4-1' ply my recommendation is to double up 3/4" with wood glue between the layers. It sound like 'overkill', but in the long run you will thank me.
For my heavy duty requirements, I flush inlet into the leading edge of the top a one piece length of 1/4"X4"X5" angle iron. I can drill and tap it to accommodate any reloading tool known to man. I also electrically ground this angle iron for total elimination of static spark danger. Not that I ever had a problem prior to taking this step. ....... Big Cholla
|
11-18-2010, 10:24 AM
|
|
US Veteran Absent Comrade
|
|
|
Join Date: Feb 2003
Location: South Central Tennessee
Posts: 1,438
Likes: 0
Liked 84 Times in 17 Posts
|
|
Another great idea; I have a workbench in my shop, approx. 36" high, 40" long, 24" wide made out of 2 pieces of 3/4" glued plywood covered with kitchen counter laminate, on heavy duty casters. I think I'll start with this bench and gauge it from there. Thanks for all these fine responses.
Pete
|
11-18-2010, 10:54 AM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,065
Likes: 10,777
Liked 15,467 Times in 6,788 Posts
|
|
Quote:
Originally Posted by oldfella
Another great idea; I have a workbench in my shop, approx. 36" high, 40" long, 24" wide made out of 2 pieces of 3/4" glued plywood covered with kitchen counter laminate, on heavy duty casters. I think I'll start with this bench and gauge it from there. Thanks for all these fine responses.
Pete
|
You mean you had a bench this whole time!!??
That sounds like a awesome bench
What's the question???????
__________________
Still Running Against the Wind
|
11-18-2010, 11:14 AM
|
|
US Veteran Absent Comrade
|
|
|
Join Date: Feb 2003
Location: South Central Tennessee
Posts: 1,438
Likes: 0
Liked 84 Times in 17 Posts
|
|
I am looking for a specialty, dedicated reloading bench, the workbench in question is my woodworking assembly bench.
Pete
|
11-18-2010, 11:37 AM
|
|
Member
|
|
|
Join Date: May 2009
Location: Southern Maine
Posts: 13,611
Likes: 491
Liked 1,883 Times in 987 Posts
|
|
Quote:
Originally Posted by oldfella
I am looking for a specialty, dedicated reloading bench, the workbench in question is my woodworking assembly bench.
Pete
|
Hello Pete,
I am planning on building my dedicated bench based on this one I found in a web search for Countertop Reloading Bench.
|
11-18-2010, 04:05 PM
|
|
Member
|
|
|
Join Date: Oct 2010
Location: Fort Worth
Posts: 478
Likes: 118
Liked 106 Times in 70 Posts
|
|
We built a house a few years ago and used (I believe) 1 1/2" tongue and groove floor decking. It had about a 2" tongue a groove that was kind of wedge shaped. I accumulated all the scrap I could and I made very nice bench tops. I believe it was about a b/c grade so there was a nice top to finish.
|
11-18-2010, 07:57 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,065
Likes: 10,777
Liked 15,467 Times in 6,788 Posts
|
|
Quote:
Originally Posted by oldfella
I am looking for a specialty, dedicated reloading bench, the workbench in question is my woodworking assembly bench.
Pete
|
Well use your woodworking skills, tools and bench to make another one just like it.
I'll have to make a trip over to my friends house who sells reloading stuff, mostly brass and ask him if I can take a picture of his reloading "room" it's about the size of my house and he must have 10 or more presses, sorters, scales counters full of dies etc.Dillons, RCBS, Hornady Old ones, new ones, shot gun loaders you name it. This is just the part in his house overlooking the lake. He has another 2,000 square foot concrete building where he sorts brass by the 55 gal drums. He has been reloading since before time began I think. The place is like a museum and just awesome!
__________________
Still Running Against the Wind
|
11-18-2010, 08:32 PM
|
|
Member
|
|
|
Join Date: Nov 2004
Location: Mountain State
Posts: 3,569
Likes: 56
Liked 379 Times in 149 Posts
|
|
I would take the wheels off of it, or you will be chasing it around the rosie's .
|
11-18-2010, 09:09 PM
|
|
US Veteran Absent Comrade
|
|
|
Join Date: Feb 2003
Location: South Central Tennessee
Posts: 1,438
Likes: 0
Liked 84 Times in 17 Posts
|
|
Quote:
Originally Posted by OCD1
Well use your woodworking skills, tools and bench to make another one just like it.
|
Yes, that is my plan - I will use my shop workbench to figure out the correct position of the press, relative to my height, and other dimensions for reloading. I will soon find out the most ergonomically comfortable height for both sitting and standing positions.
Bullseye - Yes, you are right, or anchor it to the wall.
Pete
|
11-19-2010, 10:51 AM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,065
Likes: 10,777
Liked 15,467 Times in 6,788 Posts
|
|
Quote:
Originally Posted by oldfella
Yes, that is my plan - I will use my shop workbench to figure out the correct position of the press, relative to my height, and other dimensions for reloading. I will soon find out the most ergonomically comfortable height for both sitting and standing positions.
Bullseye - Yes, you are right, or anchor it to the wall.
Pete
|
Well since you are getting ergonomic on us.
"I am here to help you with your problem. At no time will your problem become my problem as I can not help someone who does not have a problem."
Better have lots of pictures for us from blueprints to finish.
__________________
Still Running Against the Wind
|
11-19-2010, 12:31 PM
|
|
US Veteran Absent Comrade
|
|
|
Join Date: Feb 2003
Location: South Central Tennessee
Posts: 1,438
Likes: 0
Liked 84 Times in 17 Posts
|
|
OoooK. "Ergonomics" replaces "Confortable positon" ... or:
"er·go·nom·ics (ūrˌgə-nŏmˈĭks)
noun
(used with a sing. verb) The applied science of equipment design, as for the workplace, intended to maximize productivity by reducing operator fatigue and discomfort. Also called biotechnology, human engineering, human factors engineering.
(used with a pl. verb) Design factors, as for the workplace, intended to maximize productivity by minimizing operator fatigue and discomfort: The ergonomics of the new office were felt to be optimal."
Pete
|
11-19-2010, 02:44 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,065
Likes: 10,777
Liked 15,467 Times in 6,788 Posts
|
|
I have stayed at the Peabody Hotel and sat in a genuwine Herman Miller Chair, so there!
Hope you don't get splinter in you butt.
__________________
Still Running Against the Wind
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
|
|
|
|