|
|
02-03-2011, 10:20 AM
|
|
Member
|
|
|
Join Date: Dec 2007
Location: Greenfield, NH
Posts: 172
Likes: 0
Liked 0 Times in 0 Posts
|
|
Decapping
I'm having a real pain of a problem with primers that appear to stick onto the end of the pin and are being perfectly reset into the shell as the pin is withdrawn. How can that happen?
I am thinking of grinding the end down a bit. Any thoughts???
Bob
|
02-03-2011, 10:34 AM
|
Member
|
|
|
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,160
Likes: 3,620
Liked 5,205 Times in 2,173 Posts
|
|
What primers on what loader?
Some of the old-style CCI will stick on the Dillon decapper pins.
I haven't noticed any problems with current productiion.
If your pin is mushroomed, it will catch primers and needs to be replaced/modified.
__________________
Science plus Art
|
02-03-2011, 12:07 PM
|
|
Member
|
|
|
Join Date: Jul 2010
Location: Florida
Posts: 6,615
Likes: 3,393
Liked 9,264 Times in 3,482 Posts
|
|
Are you sure the decapping pin is protruding thru the primer pocket far enough? I think the problem is the pin is too short rather than too long.
All my sizing dies make a distinct ping as the primer pops out. Even if the pin were sticking to the primer, it should retain only the anvil. I think you need to adjust your decapping pin a bit deeper.
|
02-03-2011, 11:11 PM
|
Member
|
|
|
Join Date: Feb 2010
Location: Rocky Mtns, CO
Posts: 986
Likes: 19
Liked 214 Times in 141 Posts
|
|
I have never experienced what you are describing. But Dillon has a design feature in their dies specifically for what you are describing.
Dillon depriming design
|
02-03-2011, 11:32 PM
|
|
Member
|
|
|
Join Date: Mar 2008
Posts: 5,543
Likes: 667
Liked 6,774 Times in 1,312 Posts
|
|
I had an issue like that with a set of Lyman dies once, the pin was too short and had to be replaced. In your case it might just need to be turned down more.
__________________
Vaya con Dios
|
02-03-2011, 11:34 PM
|
Member
|
|
|
Join Date: Oct 2009
Location: Washington State
Posts: 116
Likes: 1
Liked 7 Times in 6 Posts
|
|
Chances are you have sharp edges on the decap pin. Round it off with some sandpaper or other gritty tool. You want a taper on the pin so the primer falls off easily.
If you using a Dillon die, another fix is to replace the decap pin with a Lyman pin - much smaller and clamps in straight and eliminates the problem.
Last edited by rodell; 02-03-2011 at 11:36 PM.
|
02-04-2011, 09:12 PM
|
|
Member
|
|
|
Join Date: Dec 2007
Location: Greenfield, NH
Posts: 172
Likes: 0
Liked 0 Times in 0 Posts
|
|
Thank you all gentlemen for the info. I can see what I have to do. Take a good good look at the tip and grind it down a bit until she works. Or as suggested, and slimmer pin. Should work
By the way, the press is Dillon and the dies are RCBS.
How primers can draw back so perfectly is a mystery. They appear perfect as they were just primed. Hummmm
Bob
|
02-05-2011, 12:58 AM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,079
Likes: 10,794
Liked 15,506 Times in 6,794 Posts
|
|
Those pins are some really hard metal. You would be able to feel if it was "buggered" at the tip. I would call RCBS before grinding away at anything. It sounds kinda strange??
__________________
Still Running Against the Wind
|
02-05-2011, 10:41 AM
|
Member
|
|
|
Join Date: Feb 2007
Posts: 2,091
Likes: 0
Liked 379 Times in 219 Posts
|
|
I use Hornady and RCBS dies in my two Dillon presses and have experienced the mysterious "re-seated spent primer" only very rarely, perhaps five times or less in tens of thousands of rounds loaded. Some shooters experience this problem quite often and I heard that the cause is a squared-off decapping pin. I suggest rounding and polishing the tip of the decapping pin of you experience this with any kind of regularity.
Dave Sinko
|
02-05-2011, 11:18 AM
|
|
Member
|
|
|
Join Date: Jul 2010
Location: Florida
Posts: 6,615
Likes: 3,393
Liked 9,264 Times in 3,482 Posts
|
|
I use both round and squared pins and never had a primer "reseat." I think I'd certainly feel it reseating. I suspect it's not being punched out at all. Like I said, the pin would be wedged in the anvil, which would pull out before the primer body seated.
|
|
Posting Rules
|
|
|
|
|