|
|
03-18-2011, 04:51 PM
|
Member
|
|
|
Join Date: Mar 2011
Location: MA - Wish I didn't.
Posts: 106
Likes: 0
Liked 0 Times in 0 Posts
|
|
Decapping LIVE primers?
Is it safe? The general shape of the primer seems to allow the decapping rod to fit right into the center of the primer, and cause no pressure to the explosive elements.
I have a bunch of rounds I miss-loaded, and would like to recycle back into new rounds (with more precise tolerances), but if I can't safely remove the primer, I won't feel safe using them, and will have to discard them.
|
03-18-2011, 05:02 PM
|
|
US Veteran
|
|
|
Join Date: Apr 2010
Location: Northern Minnesota
Posts: 1,726
Likes: 569
Liked 1,235 Times in 475 Posts
|
|
Can you pull the bullets and charge and re-load them as primed cases? To re-size the case you may need to pull the de-primer pin out of the de-capping / sizer die. I don't know how easy this would be, but if you can, you won't be touching the live primers and should be able to proceed as usual in the re-loading process.
__________________
Endeavor to persevere. <><
Last edited by Shooting Padre; 03-18-2011 at 05:10 PM.
|
03-18-2011, 05:15 PM
|
|
US Veteran
|
|
|
Join Date: Mar 2001
Location: illinois
Posts: 6,294
Likes: 1,849
Liked 6,681 Times in 2,115 Posts
|
|
It has been discussed here before, suggest you do a search. Do it slowly and wear safety glasses. I have done it numerous times and haven't had one pop yet.
|
03-18-2011, 05:57 PM
|
Member
|
|
|
Join Date: Feb 2011
Posts: 112
Likes: 0
Liked 4 Times in 4 Posts
|
|
Yes if the primers are good why waste them? I'd pull the projectiles and reclaim the bullets, gun powder & primeed cases.
In fact I recently did pull the bullets on some old and very badly stored(I'm guessing) ammo, but the primers are suspect as suspect as the powder so I do have to remove the primers to reuse the brass and the powder? It went into the compost.
|
03-18-2011, 06:00 PM
|
Member
|
|
|
Join Date: Sep 2010
Posts: 69
Likes: 0
Liked 2 Times in 1 Post
|
|
Yep- put on the glasses, go slow, I've done it many times. Unlike Hovnnes though, I don't re-use them.
|
03-19-2011, 12:10 AM
|
|
US Veteran Absent Comrade
|
|
|
Join Date: Jun 2009
Location: Texas
Posts: 7,581
Likes: 13,500
Liked 6,743 Times in 2,526 Posts
|
|
I've done it and never had one pop, but I don't like it. The primer pocket acts like a short barrel and gives the primer some velocity when it goes off. I remember being told of a 50 cal primer: it went four feet in the air, bounced off a pipe and went one inch into a 2X4. A regular primer would probably go at least an inch into flesh, and would be quite uncomfortable.
|
03-19-2011, 10:30 AM
|
|
Member
|
|
|
Join Date: Jan 2008
Location: sunny Orygun
Posts: 2,910
Likes: 392
Liked 307 Times in 195 Posts
|
|
if I have any number beyond 1 or 2 that I'm suspicious about and 'need' to deprime, usually I'll just fire the dismounted round to remove any question about the primer.
It is rare the primer fails to fire.
I'm one who doesn't feel safe depriming live primers....and don't really like disassembling loaded rounds in general.
I do use the impact hammer style and have never had any rounds detonate, nor have I even heard of such happening.
Still....
__________________
Dum vivimus Vivamas
|
03-19-2011, 12:03 PM
|
Member
|
|
|
Join Date: Jan 2010
Location: Southern Oregon
Posts: 200
Likes: 16
Liked 187 Times in 65 Posts
|
|
Not a problem..
If we look at how a primer is designed and put together we see that there are three parts to a primer.. Cup, Anvil, and Priming Mixture.
If we take a look at the Anvil, we see that it is 'pointed' toward the Cup. This creates a 'pinching' point where the firing pin will 'punch' the relatively soft Cup against the relatively hard Anvil with the Priming Mixture in between, which is what creates the flame to ignite the powder charge.
Now if we use a decapping pin to move the primer from the back, or the opposite direction, we see that there can be no 'pinching' taking place because we are moving the primer by the harder Anvil, especially considering the 'minimal' amount of force required to move the primer out of the pocket, compared with, the amount of force a firing pin exerts in an actual firearm.
The idea of using something (a decapping pin) that looks just like a firing pin to remove a primer does not set well in our minds, but in reality it is relatively safe to do so,.. with minimal force.
Just go slow and wear eye protection and you won't have a problem
|
03-19-2011, 05:15 PM
|
Member
|
|
|
Join Date: Mar 2011
Location: MA - Wish I didn't.
Posts: 106
Likes: 0
Liked 0 Times in 0 Posts
|
|
Quote:
Originally Posted by RDub
Not a problem..
If we look at how a primer is designed and put together we see that there are three parts to a primer.. Cup, Anvil, and Priming Mixture.
If we take a look at the Anvil, we see that it is 'pointed' toward the Cup. This creates a 'pinching' point where the firing pin will 'punch' the relatively soft Cup against the relatively hard Anvil with the Priming Mixture in between, which is what creates the flame to ignite the powder charge.
Now if we use a decapping pin to move the primer from the back, or the opposite direction, we see that there can be no 'pinching' taking place because we are moving the primer by the harder Anvil, especially considering the 'minimal' amount of force required to move the primer out of the pocket, compared with, the amount of force a firing pin exerts in an actual firearm.
The idea of using something (a decapping pin) that looks just like a firing pin to remove a primer does not set well in our minds, but in reality it is relatively safe to do so,.. with minimal force.
Just go slow and wear eye protection and you won't have a problem
|
Yes, that's why I thought it might be still be somewhat safe, due to the shape of the interior primer. But I was concerned about the ejector pin not lining up with that center, until I remembered that the case has a hole that would force the ejector rod to stay straight.
I am looking to just disassemble the rounds and start from scratch, saving as much of the materials as I can, including the primers, although they are relatively inexpensive.
|
03-19-2011, 08:21 PM
|
Member
|
|
|
Join Date: May 2010
Location: North East Wisconsin
Posts: 46
Likes: 3
Liked 3 Times in 3 Posts
|
|
I would remove the bullet, put the gun powder in the garden and reload the primed case again.
|
03-19-2011, 10:19 PM
|
Member
|
|
|
Join Date: Mar 2011
Location: MA - Wish I didn't.
Posts: 106
Likes: 0
Liked 0 Times in 0 Posts
|
|
Quote:
Originally Posted by Miata Mike
I would remove the bullet, put the gun powder in the garden and reload the primed case again.
|
Do you think the powder has been degraded?
|
03-20-2011, 01:49 AM
|
|
Moderator SWCA Member Absent Comrade
|
|
|
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
|
|
This comes up so often there should be a "Sticky" post on it...
__________________
Freedom is never free!!
SWCA #3437
|
03-25-2011, 07:55 AM
|
Member
|
|
|
Join Date: Mar 2008
Posts: 27
Likes: 4
Liked 0 Times in 0 Posts
|
|
Wet the primer?
After pulling the bullet and dumping the powder could you put a little water in the cartridge to wet the primer to "de-activate" it before depriming the case?
I've got a coffee can full of live rounds I've found at the range and would like to recycle the brass. I pick them up because I think it's dangerous, particularly for the grass-mowers. Understandably, scrap metal dealers don't like to recycle brass with live primers (or powder, or bullets!).
|
03-25-2011, 08:24 AM
|
|
SWCA Member
|
|
|
Join Date: Dec 2008
Posts: 6,895
Likes: 736
Liked 1,208 Times in 737 Posts
|
|
i have taken apart many live rounds with no problems...no...the powder is fine to reuse as long as you know 100% what type powder it is...i'm not sure why you would want to pull the primer at all
__________________
SWCA#2208
KK4EMO
|
03-25-2011, 08:49 AM
|
Member
|
|
|
Join Date: Mar 2011
Location: New Haven, CT
Posts: 43
Likes: 0
Liked 0 Times in 0 Posts
|
|
Pretty much echoing everyone else's experience on live primers. I've done it for years. Light consistent pressure applied with a decapping die is all it takes. If the anvil seperates or the primer compound crumples apart, cull the primer, but generally they come out without any perceptible damage. Yes, I've reloaded with them and can't recall any failures or misfires.
It's not the ideal method of reloading, but refrain from using them in carry or competition ammo and you get that extra ammo for plinking at the range and safely detonate what would have been an active waste product otherwise.
Truth be told, I've only had one primer light off and that was while priming a case. Seems I barely touched the thing and "Bang!" I wonder if it wasn't a static discharge or something or a hyper-sensitive primer element.
|
03-25-2011, 08:59 AM
|
|
Member
|
|
|
Join Date: Mar 2005
Location: DPRK (CA)
Posts: 1,498
Likes: 367
Liked 1,273 Times in 466 Posts
|
|
I had to do a quantity a while ago, I soaked the shells in hot soapy water for a few hours and then decapped as I normal. No problems at all and I didn't have to hold my breath while doing it.
|
03-25-2011, 09:27 AM
|
Member
|
|
|
Join Date: Mar 2011
Location: New Haven, CT
Posts: 43
Likes: 0
Liked 0 Times in 0 Posts
|
|
Just as a precautionary note.... I've had oil-doaked primers that still go "bang", so don't think they are disabled just because you give them a soaking in oil or water or whatever. Now, I'll grant you that I detonated them with a large hammer on an anvil, but the fact remains, they can still have explosive capacity even if treated.
Until the primer is detonated or totally removed of primer element, it can still be live.
On another note, I've fired standard primers (not 50 cal) off of a hotplate and they could hurt if you were standing right over them. They do explode!
Last edited by CTSixshot; 03-25-2011 at 09:33 AM.
|
03-25-2011, 12:53 PM
|
Member
|
|
|
Join Date: Mar 2011
Location: MA - Wish I didn't.
Posts: 106
Likes: 0
Liked 0 Times in 0 Posts
|
|
Just a follow up, I removed 50 live primers the other night without any sign of trouble.
|
03-25-2011, 01:27 PM
|
Member
|
|
|
Join Date: May 2010
Location: North East Wisconsin
Posts: 46
Likes: 3
Liked 3 Times in 3 Posts
|
|
Quote:
Originally Posted by EthanG-M&P
Do you think the powder has been degraded?
|
No, but I was thinking I would rather throw away pennies worth of powder and save the perfectly OK primed cases. Yes you could save the powder if you would have liked to. I see you are done now so it is a moot point.
|
03-25-2011, 02:08 PM
|
Member
|
|
|
Join Date: Mar 2011
Location: MA - Wish I didn't.
Posts: 106
Likes: 0
Liked 0 Times in 0 Posts
|
|
Quote:
Originally Posted by Miata Mike
No, but I was thinking I would rather throw away pennies worth of powder and save the perfectly OK primed cases. Yes you could save the powder if you would have liked to. I see you are done now so it is a moot point.
|
I am thrifty! I saved everything, but set it aside, in case I felt it wasn't safe. I accidentally lubed the inside of the shaping die when I did that ill batch, and was afraid that would have effect the powder, but I don't see any powder clumping together or anything, so I am guessing it is still good.
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
|
|
|
|