|
|
05-28-2011, 09:43 AM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,082
Likes: 10,795
Liked 15,509 Times in 6,796 Posts
|
|
For those that load 223 Rem/5.56 for semi autos
How often do you check your brass for length and how often do you need to trim it?
What type of trimmer do you use, manual, electric etc.?
I load it for a bolt action so I generally only neck size it but still check in a gauge.
Seems that running a semi auto AR there would be so much brass to have to check that there would be a lot of work with the brass.??
I sometimes shoot a AR but use military crimp ammo so I just trade it for other brass even though I have a swag die.
__________________
Still Running Against the Wind
|
05-28-2011, 01:34 PM
|
|
US Veteran
|
|
|
Join Date: Feb 2007
Location: Colorado
Posts: 1,521
Likes: 33
Liked 249 Times in 118 Posts
|
|
Quote:
Originally Posted by OCD1
How often do you check your brass for length and how often do you need to trim it?
What type of trimmer do you use, manual, electric etc.?
I load it for a bolt action so I generally only neck size it but still check in a gauge.
Seems that running a semi auto AR there would be so much brass to have to check that there would be a lot of work with the brass.??
I sometimes shoot a AR but use military crimp ammo so I just trade it for other brass even though I have a swag die.
|
Sir, when I was competing with the AR, I full-length resized and trimmed after each firing (not necessary for a bolt gun). I do the same for Garands, M14 types, etc. FWIW, the Palma bolt gunners I know follow a cycle of four or five neck sizings to one full-length resize, and then repeat the cycle.
For trimming and case checking, I used a cheap piloted Lee hand trimmer and a Wilson case gauge. Many high power guys use powered case trimmers such as the Gracey or Giraud, but they're expensive--really not cost-effective unless you're dealing with thousands of cases.
Hope this helps, and Semper Fi.
Ron H.
__________________
Wishin' don't make it so.
|
05-28-2011, 04:22 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,082
Likes: 10,795
Liked 15,509 Times in 6,796 Posts
|
|
That's what I was wondering. For by bolt action use, it is not a problem using the little Lee trimmer with the wood ball on the end. I can do 20 or 100.
Those that shoot semi autos certainly chew up a lot of ammo and I was curious about how much labor was involved just prepping the cases, let alone loading them.
I would shoot my AR more often if I didn't have to worry about case sizing. Was thinking of at least getting a better trimmer.
__________________
Still Running Against the Wind
|
05-28-2011, 05:48 PM
|
|
US Veteran
|
|
|
Join Date: Jun 2006
Location: NW Florida
Posts: 638
Likes: 647
Liked 483 Times in 146 Posts
|
|
It is a lot of work. You can use the lee trimmers with a battery powered drill. The #s for the ones I use are listed below, the #s are from Midway but they probably are lee and wilson #s.
476992
107333
389104
Wilson #456614
|
05-28-2011, 07:16 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,082
Likes: 10,795
Liked 15,509 Times in 6,796 Posts
|
|
The time consuming part for me is the tightening and un- tightening the little chuck on the shell holder.
I kinda do it opposite. I put the shell holder in my bench vice and use the cutter either with the wood ball or put it in the cordless drill. So each piece of brass involves tighten pick up cutter, trim. put down cutter remove brass, insert new brass . pick up cutter etc etc. Kinda mind numbing.
I do not mind the turning or actual cutting as that is only a few turns, it's the inserting and removal of the brass.
Thinking of getting either the RCBS with push down handle or the Hornady.
RCBS Trim Pro Manual Case Trimmer Kit - MidwayUSA
Hornady Cam-Lock Case Trimmer Kit - MidwayUSA
__________________
Still Running Against the Wind
|
05-28-2011, 07:53 PM
|
|
US Veteran
|
|
|
Join Date: Jun 2006
Location: NW Florida
Posts: 638
Likes: 647
Liked 483 Times in 146 Posts
|
|
When I get a big batch of .223s I'm going to take a closer look at the RCBS & Hornady. The threads on the lees do get tiresome.
|
05-29-2011, 12:19 AM
|
|
Member
|
|
|
Join Date: Nov 2004
Location: Mountain State
Posts: 3,568
Likes: 56
Liked 379 Times in 149 Posts
|
|
I use to send all my 223 brass to be sized, trimmed and primed for $85 per 1000, I couldn't start to do that for the price.
|
05-29-2011, 01:50 AM
|
|
Member
|
|
|
Join Date: May 2011
Location: Lynnwood, WA
Posts: 56
Likes: 2
Liked 12 Times in 10 Posts
|
|
I load and do all my case prep on a Dillon XL650 with RT1200, therefore size and load after every firing. Not my video but works like this:
http://www.youtube.com/watch?v=MLyK1UwuK3M
Last edited by Boxerglocker; 05-29-2011 at 01:53 AM.
|
05-29-2011, 10:41 AM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,082
Likes: 10,795
Liked 15,509 Times in 6,796 Posts
|
|
Quote:
Originally Posted by Boxerglocker
|
What's your address, so I can send you my brass.
Heck of a machine, don't think I am ready for that yet.
__________________
Still Running Against the Wind
|
05-29-2011, 11:00 AM
|
|
Member
|
|
|
Join Date: Mar 2005
Location: DPRK (CA)
Posts: 1,498
Likes: 368
Liked 1,273 Times in 466 Posts
|
|
if you want good results, then trimming after each firing is a good idea. If you are shooting some light loads, you can probably get away with every other loading.
The other problem is crimping, if you don't have a consistant case lenght and plan on crimping the bullets in place, you will end up with some colapsed shoulders and incosistant crimps if there is a wide range in case length.
|
05-29-2011, 12:13 PM
|
Member
|
|
|
Join Date: May 2005
Location: S.E. Minnesota
Posts: 86
Likes: 3
Liked 3 Times in 2 Posts
|
|
I try to clean(tumble), FL size, trim(forster), debur in/out, remove primer crimp(Forster), clean/cut primer cup and remove inside flash hole bur in lots of 1k or more 1 time as it is VERY labor intensive.
The upside is I can then use the brass for bolt or AR and keep seperate with details noted and then trim as needed after several firings.
One way I have tried to trim is to use the LEE trimmer by chucking the length gage and cutter assembly in drill press and hold the case in fingers while running the drill down against the press table. This eliminates the chucking and un-chucking the LEE base onto each case. It is hard on the fingers though.
There is a device I have that is made by Possum Hollow Products called KWICK CASE TRIMMER. It indexes off the case shoulder datum like a headspace gage. Cases should be fired before trimming in this device. They then are matched to the chamber. The tool is fast when used in a drill press as you just hold the brass case up into the device until the cutting is done and you do not start/stop press.
As for how often do I trim, it depends on load and rifle, I size the case after firing, either FL or neck, then measure and trim as required.
I do spend way more time prepping loading than I shoot, However to me the result is the same in the sense of enjoyment and me time LOL
I hope this helps some and if you have questions about methods discussed PM me and I'll try to better explain.
|
05-29-2011, 01:37 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,082
Likes: 10,795
Liked 15,509 Times in 6,796 Posts
|
|
It seems there is no "easy" way short of getting the Dillon machine to process a lot for semi auto use. That's why I shoot a bolt rifle more.
One of the electric machines from RCBS or Hornady would probably be sufficient for my use. I can chamfer and de burr my hand.
Anybody use the Hornady Case Prep Center? Is it worth the money?
Hornady Lock-N-Load Case Prep Center 110 Volt - MidwayUSA
__________________
Still Running Against the Wind
|
05-29-2011, 02:48 PM
|
|
Member
|
|
|
Join Date: Feb 2007
Location: Oregon
Posts: 2,403
Likes: 4,558
Liked 2,141 Times in 770 Posts
|
|
They're pretty proud of that Hornaday...
I use one of these, it's still work, but you can move through it at a pretty good clip.
RCBS Trim Pro Power Case Trimmer Kit 110 Volt - MidwayUSA
__________________
ΜΟΛΩΝ ΛΑΒΕ
|
05-29-2011, 09:49 PM
|
Member
|
|
|
Join Date: Sep 2005
Location: SE Pa
Posts: 630
Likes: 7
Liked 107 Times in 39 Posts
|
|
I have and use Lee trimmers for several calibers. When I started to reload for an AR-15 I bought the KWICK CASE TRIMMER made by Possum Hollow. If you're not familiar with it, check it out. I put the trimmer in a drill press and do a big bunch then chamfer and de-burr, each as seperate steps on the drill press. I think it does a fine job and is relatively fast...no locking of each individual case into a holder. If I didn't already have a bench-top drill press, I might have bought the cheap Harbor Freight version just for this purpose.
|
05-29-2011, 10:16 PM
|
|
Member
|
|
|
Join Date: May 2003
Location: Littleton, Colorado, USA
Posts: 1,780
Likes: 4,364
Liked 1,054 Times in 506 Posts
|
|
I don't load the .223/5.56, but I trim a lot of cases. I use the little lee tool that attaches to the bench with a screw. Pull the handle and away you go. I think it's called a zip drive, but that may be the name of some old computer back up system.
__________________
and what his trumpet saith
|
05-30-2011, 01:00 AM
|
Member
|
|
|
Join Date: Sep 2010
Location: Upper Midwest
Posts: 133
Likes: 13
Liked 43 Times in 30 Posts
|
|
I second the notion of the possum hollow kwik case trimmer.
One of the fastest trimmers out there.
|
05-30-2011, 09:44 AM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,082
Likes: 10,795
Liked 15,509 Times in 6,796 Posts
|
|
__________________
Still Running Against the Wind
|
05-30-2011, 08:02 PM
|
Member
|
|
|
Join Date: May 2005
Location: S.E. Minnesota
Posts: 86
Likes: 3
Liked 3 Times in 2 Posts
|
|
Quote:
Originally Posted by OCD1
|
I gave less than $20 at Cabelas a few years back
I do not have any kind of adapter, I put mine into drill chuck of Press
The tools' O.D. is .625"
There is another rotary drill operated trimmer device made in Spicer, MN. I think,
It is like $65 though
Not sure where I see the ad, so removed the mag. I earlier stated, for now anyway
Last edited by 2sigs; 05-30-2011 at 08:31 PM.
Reason: I don't see the ad I mentioned in Handloader
|
05-30-2011, 09:33 PM
|
US Veteran
|
|
|
Join Date: Aug 2009
Posts: 57
Likes: 10
Liked 1 Time in 1 Post
|
|
I size all my brass after every firing, in every caliber! It's fun and just part of the process.
|
05-31-2011, 04:08 PM
|
Member
|
|
|
Join Date: Feb 2007
Posts: 2,091
Likes: 0
Liked 379 Times in 219 Posts
|
|
I have trimmed at least 1500 .223 cases with the cheap Lee trimmer. With hard use, the part that screws into the holder (pilot?) will get shorter as it's constantly being turned into the handle and as such the brass will be trimmed shorter. I'm not picky on exact OAL and they're trimmed short enough that I never need to trim them again.
If I'm shooting a 3 Gun or rifle match and am not allowed to pick up my brass I just load whatever once fired boxer primed steel cases I can get my hands on. Very rarely do they stretch beyond max AOL and there's no need to trim. The primer pockets aren't crimped either so you don't have to worry about that.
Dave Sinko
|
05-31-2011, 05:44 PM
|
Member
|
|
|
Join Date: Sep 2005
Location: SE Pa
Posts: 630
Likes: 7
Liked 107 Times in 39 Posts
|
|
if you watch the video, note that the outside diameter of the case-trimmer (inside diameter of the power adopter) is the same as the deburring / chamfering tools made by (I think) RCBS and others.
|
05-31-2011, 09:27 PM
|
|
US Veteran
|
|
|
Join Date: Feb 2003
Location: Homerville, Ohio
Posts: 5,405
Likes: 28,676
Liked 9,261 Times in 2,382 Posts
|
|
I use the Dillon case trimmer for my semi-auto brass. Sizes and trims in one step and it's quick.
|
05-31-2011, 10:46 PM
|
|
Member
|
|
|
Join Date: Jul 2008
Location: Southeast Missouri
Posts: 228
Likes: 47
Liked 53 Times in 18 Posts
|
|
Quote:
Originally Posted by Ron H.
Sir, when I was competing with the AR, I full-length resized and trimmed after each firing (not necessary for a bolt gun). I do the same for Garands, M14 types, etc. FWIW, the Palma bolt gunners I know follow a cycle of four or five neck sizings to one full-length resize, and then repeat the cycle.
For trimming and case checking, I used a cheap piloted Lee hand trimmer and a Wilson case gauge. Many high power guys use powered case trimmers such as the Gracey or Giraud, but they're expensive--really not cost-effective unless you're dealing with thousands of cases.
Hope this helps, and Semper Fi.
Ron H.
|
I don't shoot AR's in competition but I do shoot quite a bit so the above answer fits me also.
I neck size for my bolt guns and only check the length occasionally.
|
|
Tags
|
223, cabelas, crimp, hornady, lock, m14, military, model 14, model 625, primer, rcbs |
Posting Rules
|
|
|
|
|