Smith & Wesson Forum

Smith & Wesson Forum (https://smith-wessonforum.com/forum.php)
-   Reloading (https://smith-wessonforum.com/reloading/)
-   -   A question for VihtaVuori users (https://smith-wessonforum.com/reloading/218295-question-vihtavuori-users.html)

buckshotshorty 11-20-2011 08:22 PM

A question for VihtaVuori users
 
I was reading the particulars, and I'm tempted to order some for my autos.

The description says it's a single base extruded powder. How does it meter through your powder measures? Does it resemble extruded rifle powders in appearance?

MKT 11-20-2011 09:38 PM

I only have loaded N320. Meters fine through my Uniflow and my Dillon. To me, it looks like a smaller version of the extruded rifle powders I have loaded with, smaller in length and diameter than the rifle powder and for my loads it burns very clean.

minconrevo 11-20-2011 09:47 PM

I've run some N310, 320 and 350. Burns very clean and consistently. Not very temperature-affected for burn rate. Meters very nicely. Works better than many powders for lead bullets.

125JHP 11-20-2011 11:06 PM

I've used 320-330-350, all about the same grain size. It is premium powder for sure - clean, consistent and not temperature sensitive - one of my favorites when I can afford it but it meters like gravel from my old RCBS hand throw. Sometimes I can get a nice smooth throw and other times it grinds. Not as bad as 4064 or other IMR powders though.

TheTinMan 11-21-2011 12:17 AM

I've used 3N37 in 9x23 Winchester and N135 in 7.62 Nato. Both meter and burn very consistently. VV has lots of free load data online too.

ChuckS1 11-21-2011 07:32 PM

4.1 grains of N310 and the Nosler/Zero 185 grain JHP is THE 50 yard load for my 1911s I use for bullseye shooting. Groups inside of 2" off a rest on a good day.

primersp 11-25-2011 11:33 AM

i use N110 in 357 and 44 mag meter good in lyman 55 or an lee auto,
N120 for rifle use (cast bullet) through an rcbs uniflow very more easy than ours vectan tubal .

snowman 11-25-2011 12:30 PM

I use N110 for .357, and echo most of the above comments. It is like the extruded powders for rifle rounds, but the sticks are shorter. It meters pretty well through my Uniflow, but not quite as well as a finer powder like H110. A very clean-burning powder also.

Andy

boatbum101 11-25-2011 12:32 PM

I shoot bullseye & use VV powders in several calibers . For 45acp target loads N310 is hard to beat , 230 ball ammo N320 is great . N340 & N320 also work fine in 38 special target loads too . It cost a bit more , it's clean burning & outstandingly accurate . If you shoot for points , what more can you ask for ?

Jitterbug 11-26-2011 10:58 AM

I've been considering giving N350 a try, so is it difficult to meter in an RCBS Uniflow?

SWKilroy 12-03-2011 08:24 AM

Quote:

Originally Posted by 125JHP (Post 136206793)
I've used 320-330-350... It is premium powder for sure - clean, consistent and not temperature sensitive .... but it meters like gravel from my old RCBS hand throw

Jitterbug, I second what 125JHP writes also for N340. Very good but very hard to meter in my Hornady powder measure.

Mind you, the problem is not so much that you get unacceptable weight deviation; rather, it's a matter of very stubborn, and unpredictable, bridging, which however does not - at least in my experience - affect weight repeatability. A real nuisance, though.

That said, I use N340 for all my 45ACP 230 and 185-grs loads, all my 38 Sp heavy bullet loads, as well as all my 357 Mag lead or plated loads, with oustanding results.

sar4937 12-03-2011 02:02 PM

I have used N320, and it is excellent. I use a Dillon powder dispenser with the smallest powder bar. In a progressive reloader .1 gr variance target is tough to measure or improve on. I have found it to meter the same as W231. It is very clean burning. I have moved on to AutoComp, which is cheaper for me.

Jitterbug 12-04-2011 09:54 AM

Well that's a bummer if N340 is difficult to meter.

I don't have much use for a crunchy high end pistol powder. I save 800x in 10mm for that task and hand weigh only.

Sounds like there might be a big difference in metering 320 vs 340?

231 flows through my RCBS Uniflow like water, so far it's been a good powder with my limited usage in .44 Mag.

boatbum101 12-04-2011 02:04 PM

I've used both & had no problem metering with a Dillon measure . If using a drum type measure any non ball / flake powder is going to have cutting issues .

125JHP 12-08-2011 09:52 PM

Yeah, I have used 320, 330 & 350 in a drum meter and they all are rough. Under a microscope I cannot tell the difference in granules between them so the burn rate difference must be the coating used.

Rosco Shooter 12-19-2011 08:27 PM

I used N320 in my Dillon 550B. The powder metered exceptionally well.

johngalt 12-20-2011 01:44 PM

N310 looks like a tiny stick powder. I only used 1# of it, but I never had any metering problems in my Hornady LNL-AP.

wxl 12-20-2011 06:37 PM

Use 3N38 for 147gr Hornady XTP in 9mm (their load data >1200 fps)


All times are GMT -4. The time now is 05:19 AM.