|
|
01-22-2012, 08:50 AM
|
Member
|
|
|
Join Date: Nov 2010
Posts: 383
Likes: 7
Liked 45 Times in 28 Posts
|
|
Case lube
Just got started reloading, Lee 4 Hole Turret, carbide dies. The 9mm seem to take more effort than the .38 special when using the first die, de-prime and sizing. There is a mention in the Lee book about SOMETIMES needing lube for 9mm. I do see some brass 'residue' after loading a few. Any recommendations?
|
01-22-2012, 09:00 AM
|
Member
|
|
|
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,160
Likes: 3,620
Liked 5,205 Times in 2,173 Posts
|
|
A lot depends on your source of brass and how clean it is. If you are using range pickup brass shot in who-knows-what, you can get oversize brass that takes more sizing effort.
If the brass is not completely clean, well, clean it before sizing to protect your dies from grit.
I never have found a reason to use lube on clean 9mm brass using carbide dies. Just push a little harder on any oversize ones.
If you are decapping military brass, the primer could be crimped in.
__________________
Science plus Art
|
01-22-2012, 09:16 AM
|
SWCA Member
|
|
|
Join Date: Jun 2003
Location: San Antonio, TX, USA
Posts: 1,451
Likes: 8
Liked 740 Times in 256 Posts
|
|
I never lube 9mm but then I get it cleaned and polished in the tumbler prior to reloading. If you want you can but it is all relative. Wait till you are resizing 357Maximum's and then the 9mm seems like nothing. 30 carbine is one I actually use lube on because it even with carbide takes a lot of force.
__________________
SWCA 1646
|
01-22-2012, 03:59 PM
|
|
Member
|
|
|
Join Date: Jan 2007
Location: Sandy Utah
Posts: 8,728
Likes: 1,582
Liked 8,856 Times in 3,534 Posts
|
|
Jamie,
9mm is both heavier (thicker) than .38 Special and tapered. Both result in needing more force to size. Clean your brass before loading and everything will be fine. There is no need to to lube cases in any caliber when using carbide dies, although doing so will reduce sizing force. The down-side is you have to clean your cases after sizing or loading, which pretty well defeats the primary reason for using carbide in the first place!
__________________
Gunsmithing since 1961
|
01-22-2012, 04:07 PM
|
|
Member
|
|
|
Join Date: Oct 2008
Location: Denver, CO
Posts: 1,813
Likes: 167
Liked 979 Times in 490 Posts
|
|
even though I don't need to, I use One Shot spray lube on my cases. As others have said, if you use range brass it's prbably dirty, and if it's been fired in a Glock, it's oversized to boot.
|
01-22-2012, 04:17 PM
|
Member
|
|
|
Join Date: May 2006
Location: Albany, OR
Posts: 458
Likes: 6
Liked 58 Times in 27 Posts
|
|
I use a little one shot now and then. Just a hint of Imperial sizing wax every so often might help as well.
|
01-22-2012, 04:34 PM
|
Member
|
|
|
Join Date: Feb 2010
Location: Rocky Mtns, CO
Posts: 986
Likes: 19
Liked 214 Times in 141 Posts
|
|
I always tumble my 9mm brass in corn cob media with some NuFinish added. The NuFinish significantly reduces the sizing effort of the 9mm brass going through the carbide die.
When I size 9mm brass (tumbled but just not with NuFinish added) the effort is significantly higher. I also notice the carbide ring will start to pick up some brass. I clean the carbide with Flitz. It does a really nice job cleaning.
|
|
Posting Rules
|
|
|
|
|
All times are GMT -4. The time now is 05:29 AM.