OK, nothing too special....little things still happen all these decades later well past when ALL those little 'oopsies' should never occur.

Had one little strange incident a few days ago....

I've been wrestling with 308 cases of late, and have had to reacquaint myself with the peculiarities of long-gun bottle neck cases.

Solved one of the unsolvable mysteries of reloading, by finally buying a NEW set of dies, which produced sparkling prime ammo for my next range outing.

But....had to take the 650 tool head off and fiddle a bit with some otherwise minor adjustments....only to discover now just where I had put that tin of Imperial sizing wax...*kaff*kaff*....

Well....it DID leave a marvelous exact impression of the decapper/resizer die and the powder funnel die in the otherwise barely used container.

And it DID give me an opportunity to find how effectively various approaches are in removing considerable-sized gobs of semi-hard wax from the dies.

Leaving the dies directly under a 60w bulb for a while does soften it considerably, if you need to know.....

__________________
Dum vivimus Vivamas

I was filling up my MEC reloader to load some shotshells. I filled the half-full powder hopper with shot....never noticed it until I finished filling the other half full hopper (shot hopper) with powder. It took a while but I salvaged it all.

A couple years ago I came across an old can of 4227, when I dumped it into the measure a redish dust came out. This can was about 20 years old and had deterioriated, so I dumped about half the powder out, it was full of red colored flakes and smelled bad. For some unkown reason I decided to check the inside of the can for rust and before thinking I stuck the ring finger of my right hand into the hole to check if the can had rusted. As soon as it went in I knew I had a problem, it wasn't gonna come out.
A moment of panic set in, all I could see was me walking into the ER with a half full can of gunpowder stuck on my hand. Thoughts of panicked ER personel calling in the bomb squad ran thru my mind. Not wanting that to happen I twisted, turned and pulled my finger back out, 'ringing' the skin and tearing it back all the way to the knuckle. It bled everywhere and hurt like crazy. For a few months I had a 'tatoo' around my finger where the ruined powder had worked its way in.
I had to put up with the Wife's ribbing for a long time afterwards but I didn't cause a scene at the local hospital.
That is one of the dumbest things I've ever done.
RD

__________________
Got a Phd from Hard Knocks U

A few weeks ago I was humming along decapping some brass on my single stage RCBS press when I got out of sequence and decapped my finger. But it was a nice neat, little puncture...Willyboy

A while back, had just completed charging 200 rounds of 38's using HP-38. When checking the visible volume AFTER weighing every 10th case, I noticed one that was had a LOT bigger charge than the others. Strange - I was sure that I didn't double charge any of the cases. Weighed the charged case - was not that much heavier. Only one thing to do - dump it and re-charge. Surprise - a stuck piece of corncob popped out with the powder. Sure got my attention - make sure I double check the volumes before seating the bullet!
RR

Realizing after loading 50 rounds of 30-06 to match specifications for a customer friend custom for his chamber that the overall case length was a tad too long. 5 hours of work down the tube.

I keep finding that my powder measure on my Hornady LNL AP likes to drift and drop a little more and more until I'm a full grain heavy if I don't adjust it. Still can't figure out what the problem is. I degreased and cleaned EVERYTHING just like the DVD showed. Everything is nice and tight that should be. And she just drifts a tiny bit more each time until I have to adjust it again. I'm using the baffle in the powder and I keep the powder at least 2/3's full when using it. This doesn't happen with my Uniflow, Lyman Ideal #55, or Lee Pro Auto Disk. This is the only powder measure I have to watch like a hawk and measure and adjust so much. I'm only using ball powders like HP-38/Win 231 most of the time, but it still did it with Bullseye and Unique was even worse. But I struggle with Unique in anything. I'm at a loss. I just got the micrometer insert to see if that holds it any better.

I was loading .44 mags with a load of 10.5 grains of Unique. problem was I set my scale for 15 grains! They were a "little stout" and required a fair amount of force to eject the empties, as in pounding on a cleaning rod for each case. Needless to say after the first cylinder full in my 629, the rest got pulled, which is when I discovered my error. This is my only mishap in over 30 years of reloading.

My eyes didn't follow the correct line in the reloading manual all the way across the page, and while working up a .44mag. load of H110, loaded a full grain over max. in several rounds. They were super accurate, but super fast, too! I didn't discover the error until I happened to be looking at the manual again some time later. Then I realized why such high velocity. No more of that nonsense.

Andy

Loading 240 grain JHPs in 44 Special using Power Pistol. As always, I looked down each powder-charged case with a flashlight. One had a double charge. Well, that's why I look ---- but that had never happened before.

I always put a name tag in the top of the powder in the powder hopper. Well, a couple months went by, I go back to the bench and realize two canisters of powder on the bench, and two name tags in the hopper. Doh, well it's either Unique or Herco- hope its not mixed.

The first time I used my Lee Classic Turret I got a primer stuck halhway into the pocket. The press was locked up. Couldn't get the shell holder out. Couldn't figure what I did wrong.

Internet to the rescue. Apparently I'm not the only one.

Ya gotta make sure your press handle can make a full upstroke without contacting the edge of your bench. :facepalm:

I decided to load some stiff 95gr .380 using N-320. Problem was I grabbed 124gr bullets instead. They shot like magnums.

I was setting up my brand-new lubrisizer and had decided to use my home-made beeswax/olive oil lube since I was loading up some blackpowder .45 Colt. I installed the sizing die, melted the lube, and confidently poured it into the lube reservoir. Imagine my horror to discover that without a bullet in the sizing die, there was nothing to keep the melted lube from running out of the holes in the sizing die, gushing out all over the place and running onto the floor. Then, of course, it immediately hardened into a nasty mess. It seemed to take forever to clean that mess up.

That reminds me. Always turn off the powder hopper before changing discs on your Auto Disc...

Interesting problem... I have always used the micrometer, and have never had an issue, mine does not vary a bit.

Have you called Hornady about the issue? They have very good CS, and should be able to make it right by you...

__________________
NRA Life Member

loaded some 45 Colts....was havin' a good time shootin' and one went puff....squib....open cylinder and there was corn cob media everywhere

I have loaded for years on single and turret presses. Well a couple months ago I dived into a Hornady LNL, What a press. Went through 38 spl like wildfire, so switched to 45 ACP.Everything goin great, I love this machine. I ran out of new brass, so I had some that had already been sized and flared, so I threw em on the press. For some reason my powder measure went nuts, only went halfway up, no powder in the cases, what the ? Got out the manual, took the PM off, disassembled, reassembled, reinstall, same thing. Wait a minute, this happened with the case change. Old sized and flared cases was letting the powder thru expander to go to deep in the case, didn't realize I had that much of a flare on the old die. Took about an hour to figure that one out.

Lee

Before I knew about 45acp Winchester NT's, I would just toss them back up into the caseloader when they failed to prime on the Dillon.

I was running a Hornady LNL. That day I was filling up 44 specials for SASS (Trail Boss 5 gr) and came up with a stoppage when a bullet wouldn't seat.

I pulled it and found a 9mm case inside the 44 special.

That case passed through the resizer where it was decapped (!), the priming station where it was reprimed, and the powder station where it was filled and flared.

Can't remember whether the 9mm case was primerless, or if the decapping pin pierced the small primer before decapping the 44 spec. But anyway, I was impressed.

__________________
HIKayaker

Used to run AmmoLoad presses, and occasionally a primer would go off while being installed. On VERY rare occasions, had an entire tube (100 or more) of primers ignite. The explosion would send the weighted follower up against the concrete ceiling, looked like a blast from a shotgun. Sure got your attention!

This just happened yesterday (after 40 years of reloading). Went to the range and was firing some 41 long colts through a SAA. First shot gave a low "pffftttt" but I saw the paper target "vibrate". Continued and got the same "pffttt" each time. First time I've fired 41 Colt. I was hitting paper. Then I realized that I was also hitting the dirt/snow halfway to the target. Bullets were ricocheting to the target (most were in the "kill zone").

Evidently, I must have loaded 0.3 gr instead of 3.0 grains. Guess I could use them in the basement for indoor practice!

...HAR!!! so I'm not "the ONLY one"...HAR HAR HAR!!!

Re: other stuff in the cases:
as a Dillon 650 devotee, I've found even with that impressive bit of engineering, certain basics can NOT be ignored.

Most common mistake for *me* was to not insure the old case was truly empty. There's a herd of critters than haul cherries for their little mousey parties...and leave the pits in various odd places...including the media.....and sometimes I'll get a pit that usually bends the decap pin. I've also had a variety of 9mm and 22LR hiding in the 45LC cases over the years. Not often, just those few times that make you realize how careful we really SHOULD be in the process.

There's others....but I ain't up to admitting nothing....

__________________
Dum vivimus Vivamas

Been there and done that and had the mess to clean up to show it...

Once I'm done with a new Mak cast bullet project then I will install the new micrometer and see if it does the same thing. But I need to cast more of my .45 ACP bullets first for loading. If the micrometer insert still does it then I will give them a call.

Mine does something similar. I have found that as I run it the powder settles in more dense and charges more as it runs up and down through the cycles, however, eventually it does stop increasing, but you have to keep your eye on it. If you give the powder measure a bunch of light taps and bumps after you first pour the powder in it eliminates a bunch of that. I have also found it's worse with ball powders than extruded or flake shaped powders. Hornady does have excellent customer service whenever I have called, but I have never asked them about that. It has to be some phenomenon because everything seems to fit perfectly together and nothing is moving, no slop, real solid. If you find a way to prevent this altogether let me know as well. I just try to settle it down as much as I can and watch it in the beginning of each session for a while.

Oh, and by the way, all I use is the micrometer inserts, those things rule for quick setup and an infinite number of charge levels.

So, do you have to use moonclips with that, or does it use the casemouth?

The long and short of it was I was hunting with a 7x57 in the morning and I pocketed some live shells before re-entering my home. At the range that afternoon one of the shells found its' way into my 30-06 rifle. No harm done, but a close call anyway. If the combination had been different, say a 308 shell in a 270 rifle, could have been bad.

I don't know if this qualifies but after loading thousands upon thousands of rounds of .38 spl., .357 mag., .357 maximum, and .44 mag., I picked up a 1911 (Springfield G.I. Love that gun.) and went for my first batch of reloads for it.

I bought a set of RCBS dies, a box of 100 Hornady 230 gr. XTP's, got out a pound of Unique and my Lyman manual, and set about it.

After getting past the process of rethinking the crimp concept and how it applies to a case that chambers at its mouth (felt like brain surgery at the time), I carefully assembled 50 rounds with my old Lee Hand Press. -I have a Dillon 550B but I wanted to give complete attention to every step of every round. Plus, I didn't have enough cash for another tool head, etc., that goes with a caliber change on the Dillon.-

So the batch is finished, inspected again, and boxed up for my next trip to the range. A couple days later, I go to the range. With much anticipation, I load up a mag full of my initial set of .45 ACP reloads ever, and rack the 1911's action to chamber the first round.

The slide stopped about 3/4 of the way forward and acted like it was spot-welded in that position. No way to get it to move either backwards or forward. Locked up like a bank vault with a live round down in the guts!

After fighting off the reflexive urge to spell "HELP!" in my Carhartts, I set about to disassembling the pistol and the round fell right out.

Turns out that the noses of the 230 gr. XTP's that I bought were much rounder than the regular hardball bullets. I figured that would aid in feeding since they were hollowpoints. I WAS WRONG! I then surmised that they were meant for reloading .45 COLT instead of .45 ACP. No way that bullet shape would feed in my 1911. All I could do was take 'em home, get out my bullet puller, alias "the dammit", and take them all apart. Haven't tried again since.

Thing is I don't have anything chambered for .45 LC. Maybe I oughtta put the box of bullets up for a Karma or sumpthin'.

"Thing is I don't have anything chambered for .45 LC. Maybe I oughtta put the box of bullets up for a Karma or sumpthin'. "

Sounds like a good excuse to buy a 25-2 or 625 (in acp).

The problem with the LNL is the powder compacts in the hopper as the arm is activated and dropped. Easy to fix, cut a strip of 3x5" index card stock about 4-5 inches long and an inch wide. Fold it long ways in in half across the short axis into a a V shape, and drop it in the hopper pointy end up so it acts like a baffle over the outflow for the measure. The powder flowing around it to exit the measure will be more consistent in density. Same for Lee autodisk measures which do this too.

Was just setting up my RCBS collet bullet puller to de-assemble
some rifle based 445 supermag ammo I made in the dark days
of early development around 1990. Somehow my left index finger
got punched. I don't think I will lose the finger nail but it
will will be a close deal.

Powder spills a couple of times.

My best bud in the 80's had a friend who's reloading equipment
we had to confiscate when he showed up with un-sized and
un-crimped 45acp. I still have the dies. He didn't complain.
We were still smoking back then and some of the gang were
less responsible than desired.

...Nemo...

About the worse thing I've done was fumble a case full as I removed it spilling the powder all over the press. I had to remove the shell plate to clean it up.

Ha ha... sounds like it's time to buy a S&W Governor. At least, that's what I'd tell my wife.

Mine is hardly original............I emptied the powder hopper on my RCBS Chargemaster, and didn't check the dumping port the next time I filled it up. To make matters worse, I wasn't standing in front of it...........So I couldn't tell my ball powder was leaking out the side almost as fast as I was pouring it in. Deep-pile carpet can absorb a LOT of powder!

Setting the belling adjustment on my Square Deal. That involves removing the powder measure to turn the die, reinstall and tighten the set screw, check belling, repeat as necessary until the desired bell is achieved. I had the belling about where I wanted it, gave the powder die one more tweak, tightened the lock ring and mounted the powder measure.

I then filled the hopper with 231 to start setting the powder charge. I placed a primed case into the station, pulled down the handle, and the measure launched itself off the top of the press, dumping its contents all over the bench. I had, of course, forgot to tighten the setscrew after that last tweak. Quite the mess.

My wife got to enjoy a string of colorful sailor talk that came out of the basement...

I've done some of those listed above. Best one lately....sized 38 super cases to shoot .357 bullets, set the cases aside for a few weeks until I had time to load them, forgot what I'd sized them for and loaded them w/ .355 bullets. Caused all kinds of problems at the range and forced me to put a bullet puller to good use.

My worst "oops" came after 10s of thousands of rounds of .38 SP loaded on my Square Deal. It's not easy to do with a SD, and I'll never know for sure how it happened, but I loaded a substantial overcharge- maybe double. I didn't know it at the time, but I sure found out when I took that round to the range!

I made a discovery today: corn cob pet litter is too big for .223 cases. Well, actually it's a perfect fit if you use it in your cleaning media. As in I had to manually poke/slam/etc. 1 out of 4 cases to get all the junk out. It was so bad that I put all 140 cases in loading trays and inspected each with a light to make sure I got all of the junk out of the cases. What a PITA!

LOL! We don't have that problem with the big revolver cases
butt it's the main reason I don't de-prime before cleaning.
That stuff is the perfect size to stick in the primer holes. I use
a mix of the corn cob and walnut media. The used up media
I sometimes load as filler in target loads. Smells "interesting".

...Nemo...

One of my best ones was deciding that cat litter might make good tumbling media, not realizing it's made of CLAY. I filled the tumbler barrel with 223 brass, topped it off with litter, and let it go for several hours. The litter clumped inside the cases, and I spent two days with a drill bit, coaxing all the little chuds of clay out of those skinny little necks!

I did two stupid things this weekend.

I was getting ready to load some .270, so I dumped the powder in the hopper. A few minutes later I decided to check whether I had the rifle or handgun insert in there, so I popped the insert out and powder starting pouring out on the floor, DOH! Been reloading for over 4 years and I have never done that before.

So the next day I was loading some .223 rounds, and I just measured a few cases since they were all from the same batch, and they were all within length. So I proceeded to reload, after 50 rounds or so I realized some of the cases of the completed were crushed and expanded at the neck. Thats when I realized I threw some of my friends cases in the batch that he didn't want, and since those were longer when I crimped them I crushed them a little. Learned a valuable lesson there, don't assume all the cases are the same length even if you just trimmed them 1 firing before that.

It just seemed so natural to set the Lee Pro Auto Disk Powder Measure powder tube upside down on the workbench... i just needed my hands for a minute...worked great till I picked it up, and left the cap and the powder in a pile on the bench...

Tom

OK, OK so last week I decided to replace the grimey corn cob media in my case vibrator. I had read somewhere (maybe here?) that pet stores carry ground up corncob and that it is much cheaper than ordering it from a gun supply place, so I stopped at one and got a big bag for $6 (paid $7 a bag the last time I bought some at a gun show a few years ago). While replacing the dirty media I noticed the new particles were quite a bit larger in size but figured they would clean better and eventually grind themselves down smaller.

I threw in a bunch of unsorted range pickups and came beck a couple hours later... sure enough they were nice and clean but also all except the straight wall pistol were filled with media. The worst were the 223 & 22-250- they were packed tight. I had to use a needle file on every one picking the over sized media out one kernel at a time. To make matters worse, this weekend at the gun show a guy was selling bags of properly ground corncob OR walnut for $4 ea.

eta... Ha! - I should have read this thread first - I now see others did the exact same thing a few posts above

I have experienced all the corn cob chunks before.. that was a fun experience. Glad someone posted about kitty litter too..Phew!

my problem Is I cant make a consistent round using my press.. Either my chain snaps, or a primer gets seated weird. Or if im in full progression my bullet seating will get longer.. and longer and longer. Making me have to single stage the whole lot in the seating again, one by one! I haven't deprimed my finger before But I had the slide of my gun catch my palm.. boy that smarts! I don't remember exactly how it happened but I think I one handed racked it and it slipped. Fumbling to grab it before it hit the ground the slide closed on my hand. It was unloaded of course.

__________________
sw9ve, 24/7 pro Ds, Hs M4

Set scale for 2.3gr instead of 3.3gr today. Hornady's collet puller is a wonderful thing. Glad it was only 8 rds.

was doin' some super's on my single stage and ran the decapper in my finger!!!!

Mine are shotshell reloading. The powder and shot tubes on my MEC reloaders have to be flip back for some reason, I think to change the charge bar, anyway, I have poured pounds and pounds of #8 shot onto and into my carpet. Covered judiciously with a similar volume of powder.

Maybe not strictly reloading oh-oh, but one of the best I had heard about, was a guy at a local range that had matching sets mod 57 and mod 29's. Both in 4" and 6", nickel and blue. He usually loaded top end magnum loads for either. Yep, loaded that mod 29 with 41 mag rounds .... had a hell of a time getting those cases out.

Charlie

Back in the 70s when I started reloading, I first used a Lee Loader on the garage workbench. As I remember the procedure, you had to drive a case down onto a primer. Probably about 10% of the primers went off. I work very hard to maintain my concentration and go slow when reloading, doublechecking, etc. But I would get awful twitchy by the time I loaded a couple hundred rounds.

__________________
Keith

The only "uh ohs" I've had were in my early reloading days, and even then it was only a couple or so. I still have the results in my reloading room somewhere.

Back in the mid-90's I did some "laugh" rounds with my son ust for jokes and giggles:

- .40 S&W bullet in a 9mm case
- .44 mag bullet in a .40 S&W case
- .45-70 bullet in a 30-06 or .308 case

No primers, no powder, just messing around with my son. I still have the examples around here somewhere also.

38/44?

__________________
Eccentric old coot