Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 02-04-2012, 10:04 PM
Snapping Twig's Avatar
Snapping Twig Snapping Twig is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: May 2007
Location: S.F. Bay Area
Posts: 3,504
Likes: 527
Liked 3,813 Times in 1,243 Posts
Default Mid Range .357

I've got lightning bolts and I have +P's, but what I needed today was a mid range magnum for my new to me K frames.

I thought about W231 and IMR 4227, but when I looked at my powder stash, Unique jumped out at me.

Consulting the books, I saw that the range of 6 ~ 8.4g would go from 900 ~ 1300fps, so I settled on 7g to push a 160g 358156 w/o the gas check somewhere in the 1100fps area.

What do you think of that load?

I have some 358156's that are loaded with 15.5g W296 that I will bring, but I'm not certain I'll use them in the K frame. They're good in the 586, and I'm toying with the idea of a round or two in my 65 to see where they land according to the fixed sights.

I'm also going to try some 358156's that I loaded into magnum cases over 5g W231 since they are +p 38 equivalents and should be fun to shoot in a 3" K frame.

Lemme know what you think of the 7g Unique load.
Reply With Quote
  #2  
Old 02-04-2012, 10:12 PM
bogman bogman is offline
Member
Mid Range .357  
Join Date: Jul 2008
Location: Dallas, Ga.
Posts: 247
Likes: 4
Liked 22 Times in 8 Posts
Default

I shoot 6.0- 6.7 gr's of unique & a 158gr. cast SWC & get excellent accuracy. all of my S&W's like unique for cast bullets.
Reply With Quote
  #3  
Old 02-04-2012, 10:27 PM
pete950's Avatar
pete950 pete950 is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Sep 2008
Posts: 1,244
Likes: 1,648
Liked 424 Times in 196 Posts
Default

Quote:
Originally Posted by bogman View Post
I shoot 6.0- 6.7 gr's of unique & a 158gr. cast SWC & get excellent accuracy. all of my S&W's like unique for cast bullets.
Im in the middle 6.5 of unique works great.
Reply With Quote
  #4  
Old 02-04-2012, 10:33 PM
Snapping Twig's Avatar
Snapping Twig Snapping Twig is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: May 2007
Location: S.F. Bay Area
Posts: 3,504
Likes: 527
Liked 3,813 Times in 1,243 Posts
Default

So you approve?

Fixed sights and all, I didn't want them to print too high to the sights, so I figured over 1000 and closer to 1100fps would be the ticket.

I have this 65-5 3" to try them in tomorrow and a 4" 13-3 I'll be picking up Tuesday (California waiting period) to see how they work out.

I'm of the opinion that since they're not making barrels for these anymore, I should treat them with respect. That and the fact that they're smaller and lighter then the N frames I shoot.

I have a 3" 629-2 that gets fed 265g cast over 22g W296, so recoil isn't a bad thing in my world, but for the mission of the 65 in particular, controlling the follow-up shot is an issue.

Fingers crossed for tomorrow.
Reply With Quote
  #5  
Old 02-04-2012, 10:51 PM
amazingflapjack amazingflapjack is offline
US Veteran
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: May 2010
Location: North Central Florida
Posts: 5,947
Likes: 24,644
Liked 6,195 Times in 2,575 Posts
Default

158 gr LSWC over 7gr of Unique is my Goldilocks load. Flapjack.
Reply With Quote
The Following User Likes This Post:
  #6  
Old 02-04-2012, 11:18 PM
sjmjax's Avatar
sjmjax sjmjax is offline
Member
 
Join Date: Nov 2005
Location: Florida
Posts: 675
Likes: 54
Liked 359 Times in 113 Posts
Default

158 grain LSWC or LRN and 6.0 grains of Unique.

You know you're out of the .38 special range but not abusive to gun nor shooter.
Reply With Quote
The Following 2 Users Like Post:
  #7  
Old 02-04-2012, 11:53 PM
txbirdman txbirdman is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Jan 2012
Posts: 80
Likes: 5
Liked 23 Times in 15 Posts
Default

I use 6.5 gr of Unique with the 358429 (173 gr) and 7 gr. with the RCBS 150 gr. (actual weight with air cooled wheel weights 157 gr.)
Reply With Quote
The Following User Likes This Post:
  #8  
Old 02-05-2012, 12:36 AM
jibjab jibjab is offline
Member
 
Join Date: Mar 2006
Location: Oregon
Posts: 119
Likes: 0
Liked 4 Times in 4 Posts
Default

I have used Unique for 38spl/.357mag, 44spl and 45acp with good results, but I had a hard time getting it to meter well in my powder throw.

I tried AA#5 as a substitute, it meters perfectly and performs very well in 45acp and 9x18 Makarov. #5 also did well for me with heavy 38spl loadings, 44 spl and mid range .357 mag.

I am not trying to bash Unique as it is a great powder, but for now I am exploring other options.
Reply With Quote
The Following User Likes This Post:
  #9  
Old 02-05-2012, 12:44 AM
358156hp 358156hp is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Dec 2011
Location: Nebraska
Posts: 728
Likes: 97
Liked 224 Times in 149 Posts
Default

I've come back to Unique many times. I won't give it up again. I know it can be dirty, but I have to clean the guns anyway, and a quick wipe down is usually all it needs. It meters okay through my Dillon powder measure.
Reply With Quote
  #10  
Old 02-05-2012, 12:48 AM
Dragon88 Dragon88 is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Dec 2009
Location: North Carolina
Posts: 3,054
Likes: 107
Liked 456 Times in 205 Posts
Default

"Flammable dirt" is a mainstay isn't it? I always come back to Unique or W231 for my mid-range loads, they just work so well.
Reply With Quote
  #11  
Old 02-05-2012, 06:27 AM
ArchAngelCD's Avatar
ArchAngelCD ArchAngelCD is offline
Moderator
SWCA Member
Absent Comrade
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,068 Times in 2,660 Posts
Default

I use W231 for light midrange .357's and for heavier midrange loads it's all about HS-6. HS-6 is very accurate with lead bullets and the pressures are on the low side for the velocities it develops.
__________________
Freedom is never free!!
SWCA #3437
Reply With Quote
  #12  
Old 02-05-2012, 07:22 AM
jimkim's Avatar
jimkim jimkim is offline
Member
 
Join Date: Mar 2009
Posts: 121
Likes: 16
Liked 12 Times in 12 Posts
Default

10.0gr of AA#7 under a 158gr SWC
Reply With Quote
  #13  
Old 02-05-2012, 09:08 AM
Mule88's Avatar
Mule88 Mule88 is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Jul 2004
Location: Vandalia, Ohio
Posts: 1,751
Likes: 297
Liked 231 Times in 137 Posts
Default

Im using 6-6.5 gns Universal clays, with 158 gn cast, burns cleaner than Unique and very accurate

Last edited by Mule88; 02-07-2012 at 10:16 AM.
Reply With Quote
  #14  
Old 02-05-2012, 08:02 PM
Snapping Twig's Avatar
Snapping Twig Snapping Twig is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: May 2007
Location: S.F. Bay Area
Posts: 3,504
Likes: 527
Liked 3,813 Times in 1,243 Posts
Default OMG!!!

I told you these were 358156 and that I loaded them w/o GC.

THEY TUMBLED! No ****! At 7 yards, 2 out of 6 tumbled.

This was in my 3" 65-5.

I tried them in a 4" 586-1 and a 5" 27-0 and they shot fine.

They went where I pointed the barrel, but they tumbled, so these are a no-go for the 65-5. I expect the extra barrel length made the difference with the other two revolvers and this gives me hope of the 4" 13-3 I'll be trying them in next week.

The best news is that I shot near 100 full power 160g cast (358156 wGC) over 15.5g W296 and it ate 'em up! One big hole at 7 & 10 yards.

I also used a magnum case and 5g W231 under the same bullet w/o GC and they shot just fine. No tumbling, no issue, accurate as sin.

So, souping up these bullets and not using the GC doesn't work in my 3" 65. I bet if I used the GC they'd work, so further experiments to follow.
Reply With Quote
  #15  
Old 02-06-2012, 12:02 AM
txbirdman txbirdman is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Jan 2012
Posts: 80
Likes: 5
Liked 23 Times in 15 Posts
Default

You might try sizing the bullets about .001 larger and trying again. I've found that when cast bullets tumble it's usually because they are undersized for that particular firearm.
Reply With Quote
  #16  
Old 02-06-2012, 01:24 AM
Snapping Twig's Avatar
Snapping Twig Snapping Twig is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: May 2007
Location: S.F. Bay Area
Posts: 3,504
Likes: 527
Liked 3,813 Times in 1,243 Posts
Default

They're sized to .358 and can't pass through the cylinder unless I smack 'em with a dowel.

Like I mentioned, the other loads shot straight and true, just not these.

I will keep an open mind, but I am leaning to the no gas check on a checked bullet design at moderate speed as a contributing factor.

All the loads I put through it were the same bullet, sized the same made from the same alloy. The magnums with the gas checks installed were fantastic as were the +P loads w/o the gas checks, but boosting the speed and no check didn't work out so well.
Reply With Quote
  #17  
Old 02-06-2012, 02:41 AM
jibjab jibjab is offline
Member
 
Join Date: Mar 2006
Location: Oregon
Posts: 119
Likes: 0
Liked 4 Times in 4 Posts
Default

[QUOTE=Snapping Twig;136331054]I told you these were 358156 and that I loaded them w/o GC.

THEY TUMBLED! No ****! At 7 yards, 2 out of 6 tumbled.

This was in my 3" 65-5.=QUOTE]

Could the bullets be skipping the riflings ? Not enough bearing surface (driving band) for a short barrel. I guess this kinda go along with post #15.

Without the GC there isn't much for the barrel to hold on to.
Reply With Quote
  #18  
Old 02-06-2012, 03:00 AM
Snapping Twig's Avatar
Snapping Twig Snapping Twig is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: May 2007
Location: S.F. Bay Area
Posts: 3,504
Likes: 527
Liked 3,813 Times in 1,243 Posts
Default

I'm leaning that way.

At +P velocity they spin up nice and go exactly where you want them to, but go past 900fps and the dynamics change.

Same bullet with the GC was a laser at full magnum velocity.

This mid range magnum out of the other 4" & 5" S&W's we had there today shot well, so IMO, the 3" barrel and no GC made for not enough stabilizing.

I'll be loading up some with the GC to compare.

But... seems my worries about needing a mid range magnum were not valid. The 15.5g W296 rounds (same bullet WITH GC) shot just fine.

If I can get these midrange mags working, and I believe it's an easy fix, they recoil a lot less and are worth the effort to have.
Reply With Quote
  #19  
Old 02-06-2012, 03:32 AM
jibjab jibjab is offline
Member
 
Join Date: Mar 2006
Location: Oregon
Posts: 119
Likes: 0
Liked 4 Times in 4 Posts
Default

Maybe a different bullet is needed ?

I am thinking of these for a 2.75" Ruger Sec. Six

.357 Keith 170 gr. SWC-FB per 500 .357 Keith 170 gr. SWC-FB [SWC] - $36.00 : Rim Rock Bullets, Premium Cast Lead Bullets
Reply With Quote
  #20  
Old 02-06-2012, 07:15 AM
Charliee Charliee is offline
Member
 
Join Date: Dec 2007
Posts: 46
Likes: 0
Liked 4 Times in 3 Posts
Default

For my mid range loads I use a 158 gr lead swc on top of 7 grains of Unique. I figure its about a 3/4 power load. I find it snappy but fun to shoot.
Reply With Quote
  #21  
Old 02-06-2012, 07:22 PM
parabarbarian parabarbarian is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Sep 2010
Location: Southern California
Posts: 299
Likes: 12
Liked 34 Times in 26 Posts
Default

Your load sounds about right. My "mid-range" 357 load is 8.0 gr of Power Pistol under 158 gr FP or SWC.
Reply With Quote
The Following User Likes This Post:
  #22  
Old 02-06-2012, 08:10 PM
harleydrivinglawnerd harleydrivinglawnerd is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Jan 2012
Posts: 33
Likes: 1
Liked 5 Times in 1 Post
Default

Do you use magnum primers with that much unique?
Do you get any lead fouling at that speed?

I had some 38 spl. 158 grain LSWC loaded with 4.8 grains Unique and it seems I was getting some leading at those loads.

Love to load some 357 magnum but have been worried about leading.

Thanks
Reply With Quote
  #23  
Old 02-06-2012, 09:36 PM
ruger-p94's Avatar
ruger-p94 ruger-p94 is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Oct 2011
Location: Ruskin Florida
Posts: 193
Likes: 21
Liked 78 Times in 41 Posts
Default

I'm loading for the first time tomorrow and using the 158 LSWC I cast and the Lee book says the starting load for it is 5.2 and max is 6.0. for Unique. I figure I will start off around 5.5 and get a good base line on what the light load is and then work up till I find a nice accurate target load for my 13-3
Reply With Quote
  #24  
Old 02-07-2012, 01:35 AM
sjmjax's Avatar
sjmjax sjmjax is offline
Member
 
Join Date: Nov 2005
Location: Florida
Posts: 675
Likes: 54
Liked 359 Times in 113 Posts
Default

Harley guy,

I'd suggest you try the hotter .357 loads.

I have been using the same Space Coast cast 158 grain LSWC in both .38 special and .357 loads.

At the modest .38 special loadings with these hard cast bullets, I get heavy leading in a several different .38 special revolvers. When I go to the hotter .357 loads with the same bullets, the leading problem completely goes away.

This phenomenon has been frequently discussed on the reloading board.
Reply With Quote
  #25  
Old 02-08-2012, 12:56 AM
Snapping Twig's Avatar
Snapping Twig Snapping Twig is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: May 2007
Location: S.F. Bay Area
Posts: 3,504
Likes: 527
Liked 3,813 Times in 1,243 Posts
Default

Quote:
Originally Posted by ruger-p94 View Post
I'm loading for the first time tomorrow and using the 158 LSWC I cast and the Lee book says the starting load for it is 5.2 and max is 6.0. for Unique. I figure I will start off around 5.5 and get a good base line on what the light load is and then work up till I find a nice accurate target load for my 13-3
Amazing how different various books can be.

My data shows 6 ~ 8.4g.... Wait, I think I know what's up...

The data for LEAD is lower and the data for jacketed is higher.

I have been loading for 30 years, so I have had experience, therefore I suggest you gain yours in the safest way possible - through caution and good records.

I used the jacketed data as weight is MOST important. Construction is too, but here's where experience pays dividends and allows deviation from the data. If you understand that jacketed bullets have more resistance than lead, you realize that pressure is lower for a given bullet weight - jacket vs lead.

You also gain velocity with lead over jacketed for the same powder charge.

With that in mind, I used the jacketed data for my loads in both the 65-5 and today, the 13-3 - just like yours.

I found that the 7g Unique load with a cast 160g SWC shot to POA in the 13.3 and it is accurate indeed.

Work your way up to it and let us know what you think of that load, which is not a maximum load in any event.
Reply With Quote
  #26  
Old 02-08-2012, 07:46 AM
ruger-p94's Avatar
ruger-p94 ruger-p94 is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Oct 2011
Location: Ruskin Florida
Posts: 193
Likes: 21
Liked 78 Times in 41 Posts
Default

I also noticed in the book that the oal is 1.570. I understand you can not go below this or you will increase the pressure quite a bit. I am using a Lee tumble lub bullet and there is a groove for a crimp around the 1.65 mark. My understanding is going to that mark will only lower the pressure of the bullet and it will still fit in the revolver with lots to spare. I was planning to make 15 rounds like that and try them out and if the round "felt" slow then I could put a few more grains in but keep it at the larger oal.
Reply With Quote
  #27  
Old 02-08-2012, 11:31 AM
Snapping Twig's Avatar
Snapping Twig Snapping Twig is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: May 2007
Location: S.F. Bay Area
Posts: 3,504
Likes: 527
Liked 3,813 Times in 1,243 Posts
Default

Quote:
Originally Posted by ruger-p94 View Post
I also noticed in the book that the oal is 1.570. I understand you can not go below this or you will increase the pressure quite a bit. I am using a Lee tumble lub bullet and there is a groove for a crimp around the 1.65 mark. My understanding is going to that mark will only lower the pressure of the bullet and it will still fit in the revolver with lots to spare. I was planning to make 15 rounds like that and try them out and if the round "felt" slow then I could put a few more grains in but keep it at the larger oal.
Lead bullets have a crimp groove for a reason - use it.

You get a good crimping spot to prevent bullet set-back (increased pressure surprise) and OAL is right for that bullet when loaded according to Mfg's. SAAMI data.

Here again, the exception and experience shows up with a combination like the Lyman 359429 (long) and the N frame cylinder (short). You have a long cylinder on the 13, so no worries, but that bullet needs to be crimped in a "different" location and the powder charge modified to accomodate this condition.

Welcome to the reloading world.
Reply With Quote
  #28  
Old 02-08-2012, 02:34 PM
BE Mike's Avatar
BE Mike BE Mike is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Sep 2003
Location: Indiana
Posts: 3,567
Likes: 2,230
Liked 3,461 Times in 1,469 Posts
Default

I have been using 4.0 grains of American Select with a 158 gr. lead semi-wadcutter in my .357 mag. Rossi Ranch Hand. It is a great load for that pistol.
Reply With Quote
  #29  
Old 02-08-2012, 05:42 PM
squarles67 squarles67 is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Feb 2011
Location: Orange, Texas
Posts: 15
Likes: 0
Liked 1 Time in 1 Post
Default

6 grains of Unique aka "Flaming Dirt" in a 357 case with a 158g lead RNFP gives me 1100 fps put of a 6" model 66-2
Reply With Quote
The Following User Likes This Post:
  #30  
Old 02-09-2012, 04:45 PM
ruger-p94's Avatar
ruger-p94 ruger-p94 is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Oct 2011
Location: Ruskin Florida
Posts: 193
Likes: 21
Liked 78 Times in 41 Posts
Default

Got back from the range after testing my first load. I used 5.2 grains of Unique with the 158 grain lead WC. I was able to get a nice tight 2 1/2 grouping with not much recoil. I think I will add three grains and round it off at 5.5 with the oal at 1.580. Very happy with the load....
Reply With Quote
The Following User Likes This Post:
  #31  
Old 02-10-2012, 11:09 PM
fredj338's Avatar
fredj338 fredj338 is offline
Member
 
Join Date: Feb 2006
Location: Kalif. usa
Posts: 6,836
Likes: 2,665
Liked 3,927 Times in 2,366 Posts
Default

If I could only have one pistol powder, it would be Unique. A 6.5-7gr charge under a 158gr LSWC is an easy shooting accurate load in most 357mags.
Reply With Quote
  #32  
Old 02-12-2012, 12:05 AM
jibjab jibjab is offline
Member
 
Join Date: Mar 2006
Location: Oregon
Posts: 119
Likes: 0
Liked 4 Times in 4 Posts
Default

Quote:
Originally Posted by fredj338 View Post
If I could only have one pistol powder, it would be Unique. A 6.5-7gr charge under a 158gr LSWC is an easy shooting accurate load in most 357mags.
I have had my fill of Unique had it's poor metering characteristics, I guess its not a big deal at mid range loadings but when I load at the upper end I can not get Unique to meter consistently enough to feel comfortable with the charge.

My next candidate for a Unique replacement will likely be Universal.
Reply With Quote
  #33  
Old 07-03-2018, 09:05 PM
sniper sniper is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: May 2008
Posts: 258
Likes: 1,346
Liked 138 Times in 85 Posts
Default

Quote:
Originally Posted by ruger-p94 View Post
Got back from the range after testing my first load. I used 5.2 grains of Unique with the 158 grain lead WC. I was able to get a nice tight 2 1/2 grouping with not much recoil. I think I will add three grains and round it off at 5.5 with the oal at 1.580. Very happy with the load....
5.5 gr. Unique/150 gr. RCBS mould= 860 fps/std primer/ 357 brass 4" bbl. Good load!
Reply With Quote
  #34  
Old 07-03-2018, 10:56 PM
jerry52 jerry52 is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Sep 2009
Location: over by there
Posts: 76
Likes: 1
Liked 81 Times in 38 Posts
Default

5.5 Unique with 158 swc speer or hornady light recoil very accurate. six oclock hold full power load are dead on (146 1/2 jacket swc 17.0 grains 296
Reply With Quote
The Following User Likes This Post:
  #35  
Old 07-03-2018, 11:25 PM
Eddietruett Eddietruett is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Dec 2016
Location: South Carolina
Posts: 1,702
Likes: 1,047
Liked 3,508 Times in 955 Posts
Default

Quote:
Originally Posted by Mule88 View Post
Im using 6-6.5 gns Universal clays, with 158 gn cast, burns cleaner than Unique and very accurate
I've switched from Unique to Universal as well. Cleaner and meters much better in my Dillon 650 and I find it a very accurate mid range powder.
Reply With Quote
The Following User Likes This Post:
  #36  
Old 07-04-2018, 12:47 AM
LoboGunLeather's Avatar
LoboGunLeather LoboGunLeather is offline
US Veteran
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Nov 2008
Location: Colorado
Posts: 7,518
Likes: 19,273
Liked 32,337 Times in 5,474 Posts
Default

Nearly all of my .357 magnum shooting is done with K-frame revolvers (Model 19, Model 66, etc). I use two cast bullets, one is a 158SWC, the other is a 145RN-HP. Both do very well using 7.0 grains Unique, standard primers. Accurate, controllable, comfortable to shoot. I have not chronographed these, but I suspect velocities in the 1100-1150FPS range; a significant boost over .38+P levels, but not hard on guns or shooters at all.

I've been using Unique in several handgun calibers for over 40 years. I find it to be consistent and reliable. I see others commenting on metering problems, which I've never experienced with my Lachmiller powder measure. I see others commenting on dirty guns, which I have never noticed to any degree (even when shooting 200 rounds or more), I just clean as usual with no great difficulty.
Reply With Quote
The Following User Likes This Post:
  #37  
Old 07-04-2018, 12:50 AM
JayFramer JayFramer is offline
Banned
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Jul 2013
Posts: 4,596
Likes: 6,989
Liked 9,328 Times in 2,759 Posts
Default

I love a good 6" .357 magnum LOVE one.

Gets them pills a movin!!
Reply With Quote
  #38  
Old 07-04-2018, 08:00 AM
rufgr rufgr is offline
Member
 
Join Date: Jun 2005
Location: Indiana
Posts: 135
Likes: 109
Liked 562 Times in 69 Posts
Default

My favorite 357 load is 6 grains of Unique and a Lyman 358429. This is a very accurate load with my model 27.
Reply With Quote
  #39  
Old 07-04-2018, 10:14 AM
jeeps jeeps is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Jan 2012
Location: Southside
Posts: 919
Likes: 280
Liked 1,278 Times in 417 Posts
Default

Yep 6.5 to 7 grains with 158 swc. Even kills deer fine .
Reply With Quote
  #40  
Old 07-05-2018, 01:01 PM
Qc Pistolero Qc Pistolero is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: May 2016
Location: 30min SE Montreal
Posts: 2,026
Likes: 150
Liked 1,540 Times in 841 Posts
Default

I use 6.9 under a 154gr swc.Good for a little over 1000fps
Reply With Quote
  #41  
Old 07-05-2018, 07:37 PM
cowboy4evr cowboy4evr is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Jun 2016
Location: for now ,Texas
Posts: 2,738
Likes: 185
Liked 3,297 Times in 1,523 Posts
Default

This thread is 6 yrs old but people have started adding to it so here is my favorite 357 load . 7.5 grs of WSF using any bullet weight from 158-173 gr swc . This is my " unique replacement " load . Prior to WSF , I used unique and my fav load was 7.0 grs for same weight bullets posted above .
Reply With Quote
  #42  
Old 07-14-2018, 11:24 AM
sniper sniper is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: May 2008
Posts: 258
Likes: 1,346
Liked 138 Times in 85 Posts
Smile

Quote:
Originally Posted by harleydrivinglawnerd View Post
Do you use magnum primers with that much unique?
Do you get any lead fouling at that speed?

I had some 38 spl. 158 grain LSWC loaded with 4.8 grains Unique and it seems I was getting some leading at those loads.

Love to load some 357 magnum but have been worried about leading.

Thanks
Magnum primers are not needed with Unique, or many other common .38 Spl/357 Magnum powders. Bullseye, Blue Dot, Universal, AA#5, Love Potion #9, etc., etc.

For years, I shot a home cast bullet. WW/scrap/ 50-50 bar solder/fishing sinkers, melted on my Coleman camp stove. I fondly hoped the mix was somewhere close to Lyman #2 alloy. 150 gr RCBS swc mould, sized to the cylinder mouths....357, 5,5 gr of Unique=860 fps, no leading.
Commercial "hard" cast, same load= leading, soooo, I solved the problem by buying a Lewis Lead Remover kit. Works fine.

Now, I use 6.0 gr Unique, which is as close to Magnum as I want to be. Except...maybe hunting Saber-Tooth Tigers. which I don't do any more...No more room on the walls for another head and my wife's quilting. SHE says at 79, I'm getting too old! I'm sure I don't know what she is talking about!

New revolver, now, .358 cylinder mouths, boolits sized for them.

Worrying takes all the fun out of it, when there are remedies. Do the best you can, don't sweat the small stuff, shoot often and much,and FEAR NOT!
Reply With Quote
The Following User Likes This Post:
  #43  
Old 07-14-2018, 12:04 PM
cowboy4evr cowboy4evr is offline
Member
Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357 Mid Range .357  
Join Date: Jun 2016
Location: for now ,Texas
Posts: 2,738
Likes: 185
Liked 3,297 Times in 1,523 Posts
Default

Speaking of cylinder throats , I recently bought a 19-5 , 4” nickel . When checking the cylinder throats I discovered they were a consistent .355 using pin gauges . I wondered how many owners had complained about a leaded barrel previously. I opened them up . I lucked out as the barrel had no “ barrel to frame “ choke . It’s very very accurate and NO leading of the barrel. Regards Paul
Reply With Quote
The Following User Likes This Post:
Reply

Tags
357 magnum, 38spl, 45acp, 586, 629, crimp, fouling, model 66, rcbs, rossi, ruger, universal, wadcutter

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Rifle range improvements, I now have a 220 yard range in my back yard (pics)... canoeguy The Lounge 20 07-13-2022 10:32 PM
Disappointing K22 range report/UPDATE-range report Old Corp S&W Hand Ejectors: 1896 to 1961 27 02-15-2016 12:56 PM
SA Range Officer Range Report UPDATE...I got it back from SA! See Post 22 Rawhyde The Lounge 46 03-02-2014 12:24 PM
Range Report 11/25/12 w/pics + 11/30 range report oneyeopn Smith & Wesson M&P15 Rifles 45 12-01-2012 12:17 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 03:26 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)