|
|
02-10-2012, 06:42 PM
|
Member
|
|
|
Join Date: Nov 2008
Location: Upstate, S.C.
Posts: 1,155
Likes: 78
Liked 220 Times in 133 Posts
|
|
3-die set vs. 4-die set for 45acp
Ok, I seem to be having a little trouble getting my sizing correct for plated 230grn round noce 45acp and was wondering if a 4-die set might work a little better. The brass cuts into the bullet. I don't seem to have a problem with FMJ in 45acp (or 9mm) when using the 3-die set.
Using a single stage RCBS.
What are most folks using with a single stage.
Thank you all.
|
02-10-2012, 06:46 PM
|
|
US Veteran
|
|
|
Join Date: Feb 2003
Location: Homerville, Ohio
Posts: 5,405
Likes: 28,676
Liked 9,261 Times in 2,382 Posts
|
|
If the brass is cutting into the bullet, you need to flare the case mouth more to accept the base of the bullet easier.
I think with a 4 die set, the 4th die is for taper crimping, whereas the 3rd die is for a roll crimp.
|
02-10-2012, 10:59 PM
|
|
Member
|
|
|
Join Date: Feb 2006
Location: Kalif. usa
Posts: 6,836
Likes: 2,665
Liked 3,927 Times in 2,366 Posts
|
|
Quote:
Originally Posted by bgrafsr
If the brass is cutting into the bullet, you need to flare the case mouth more to accept the base of the bullet easier.
I think with a 4 die set, the 4th die is for taper crimping, whereas the 3rd die is for a roll crimp.
|
The Lee 4 die set is exactly that. If the brass is cutting into the bullet during seating, flare more. DO NOT use the FCD to finish, ****** product & all it does is mess w/ accuracy, especially w/ plated bullets. If the "cutting" is after the crimp, too much crimp. This also messes w/ accuracy.
|
02-11-2012, 12:04 AM
|
|
Member
|
|
|
Join Date: Aug 2008
Location: S/W Texas
Posts: 638
Likes: 261
Liked 232 Times in 132 Posts
|
|
Quote:
Originally Posted by fredj338
The Lee 4 die set is exactly that. If the brass is cutting into the bullet during seating, flare more. DO NOT use the FCD to finish, ****** product & all it does is mess w/ accuracy, especially w/ plated bullets. If the "cutting" is after the crimp, too much crimp. This also messes w/ accuracy.
|
Wow, why would you not use the Lee FCD die to finish? I find it to be the the answer to feeding and crimping problems, especially with plated bullets.
|
02-11-2012, 12:13 AM
|
|
Member
|
|
|
Join Date: Jan 2011
Location: North Central, Indiana
Posts: 254
Likes: 43
Liked 53 Times in 28 Posts
|
|
In a single stage, as well as my Dillon, I always crimp separately after seating the bullet. If you're using a die that performs both operations simultaneously then the result can be damaged bullets.
As a side note I'm a Huge fan of Redding dies. But, I've also bought some Lee dies (I told myself it would never happen) and found them to work just fine.
|
02-11-2012, 01:40 AM
|
Member
|
|
|
Join Date: Dec 2011
Location: North Mississippi
Posts: 202
Likes: 16
Liked 34 Times in 22 Posts
|
|
I havnt had any problems with the 4 die lee 45 acp. Flare a bit more. Ive used plated and cast. Both feed well and accuracy is fine.
|
02-11-2012, 02:01 AM
|
|
Member
|
|
|
Join Date: May 2004
Location: Coastal Missouri
Posts: 1,898
Likes: 899
Liked 977 Times in 467 Posts
|
|
Quote:
Originally Posted by fredj338
DO NOT use the FCD to finish, ****** product & all it does is mess w/ accuracy, especially w/ plated bullets.
|
My mileage varies quite a bit from yours.
|
02-11-2012, 05:24 AM
|
|
Moderator SWCA Member Absent Comrade
|
|
|
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
|
|
I use the Lee 4 die set for most of my handgun reloading and they work just fine... I haven't had any accuracy problems when using the FCD.
__________________
Freedom is never free!!
SWCA #3437
|
02-11-2012, 11:08 AM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,082
Likes: 10,795
Liked 15,509 Times in 6,796 Posts
|
|
Quote:
Originally Posted by fredj338
The Lee 4 die set is exactly that. If the brass is cutting into the bullet during seating, flare more. DO NOT use the FCD to finish, ****** product & all it does is mess w/ accuracy, especially w/ plated bullets. If the "cutting" is after the crimp, too much crimp. This also messes w/ accuracy.
|
I disagree completely.
The LFCD for semi auto calibers taper crimps and can not be over crimped to screw up headspace.. The revolver version roll crimps.
Both can be set to crimp exactly how you want.
Some folks complain that it resizes lead bullets and makes them too small for their bores/cylinders. I have never slugged a bore or cylinder and do not seem to have a problem with any lead bullets in any caliber.
If Dillon made one it would be the greatest invention since sliced bread.
__________________
Still Running Against the Wind
|
02-11-2012, 06:41 PM
|
|
Moderator SWCA Member Absent Comrade
|
|
|
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
|
|
Quote:
Originally Posted by Rule3
I disagree completely.
The LFCD for semi auto calibers taper crimps and can not be over crimped to screw up headspace.. The revolver version roll crimps.
Both can be set to crimp exactly how you want.
Some folks complain that it resizes lead bullets and makes them too small for their bores/cylinders. I have never slugged a bore or cylinder and do not seem to have a problem with any lead bullets in any caliber.
If Dillon made one it would be the greatest invention since sliced bread.
|
I can't agree more... Like I said above, I have never had a accuracy problem when using a Lee FCD.
__________________
Freedom is never free!!
SWCA #3437
|
02-11-2012, 07:42 PM
|
US Veteran
|
|
|
Join Date: May 2010
Location: North Central Florida
Posts: 5,947
Likes: 24,644
Liked 6,195 Times in 2,575 Posts
|
|
I find a propperly sized hard cast lead bullets of about 18BHN preclude my need for any kind on jacket. Cylinder throat size is the key measurement in my experience. Lee FCD is a great tool, especially for revolvers. I did have a situation with my 1006 where I had to eliminate the FCD stage, and just use 3 stages.
|
02-11-2012, 07:56 PM
|
|
Member
|
|
|
Join Date: Dec 2008
Location: arkansas
Posts: 236
Likes: 4
Liked 15 Times in 11 Posts
|
|
I like the separate seating and crimping dies. Also check the flaring to make sure the plated bullets sit straight in the brass.
|
02-11-2012, 08:49 PM
|
|
US Veteran
|
|
|
Join Date: Mar 2001
Location: illinois
Posts: 6,296
Likes: 1,850
Liked 6,685 Times in 2,117 Posts
|
|
I use 4 dies for the 45acp and have no problems.
|
02-11-2012, 09:02 PM
|
|
Member
|
|
|
Join Date: Nov 2011
Location: Baton Rouge, La.
Posts: 6,874
Likes: 7,481
Liked 8,131 Times in 3,678 Posts
|
|
Seat the bullet then crimp in a seperate step. This works better in all reloading but especially with cast or plated bullets...they are softer . You dont need a seperate die ... just back out the seat/crimp die untill it does not crimp and seat all the bullets. Then remove or back out the seating stem and crimp all the bullets . It may be a pain to adjust the die for each step but it does result in a little better crafted ammo . Reloading cast bullet handgun ammo , auto or revolver just about requires the two steps to be done seperately.
Hope this helps....gary
|
02-11-2012, 10:52 PM
|
Member
|
|
|
Join Date: Nov 2006
Posts: 2,690
Likes: 6
Liked 351 Times in 243 Posts
|
|
If you've done everthing right you don't need a Lee FCD.
Seat and crimp in two seperate steps and if you are getting too much crimp, adjust your dies so it doesn't do it as much.
On a single stage press I use the seat/crimp die to do both steps seperately. On a progressive I usually use a standard Lee seat/crimp die to perform the crimp operation after the bullet was seated in a previous step.
|
02-12-2012, 02:02 AM
|
US Veteran Absent Comrade
|
|
|
Join Date: Jan 2010
Location: San Diego, PRK
Posts: 9,237
Likes: 11,531
Liked 11,249 Times in 3,916 Posts
|
|
Quote:
Originally Posted by Rule3
I disagree completely.
The LFCD for semi auto calibers taper crimps and can not be over crimped to screw up headspace.. The revolver version roll crimps.
Both can be set to crimp exactly how you want.
Some folks complain that it resizes lead bullets and makes them too small for their bores/cylinders. I have never slugged a bore or cylinder and do not seem to have a problem with any lead bullets in any caliber.
If Dillon made one it would be the greatest invention since sliced bread.
|
^^^This. Especially the last part...
Actually I believe Dillon does make a taper crimp die. I could be wrong....
EDIT: Aha! From Big Blue's website...
Quote:
NOTE: All Dillon Pistol Die sets include our sizer/ decap die, seat die and a separate crimp die. (Taper crimp for autos; accu-crimp for revolvers.)
|
Last edited by Fishslayer; 02-12-2012 at 02:07 AM.
|
02-12-2012, 02:12 AM
|
US Veteran
|
|
|
Join Date: Nov 2007
Location: Ridgecrest, CA
Posts: 714
Likes: 43
Liked 842 Times in 331 Posts
|
|
Quote:
Originally Posted by Jellybean
If you've done everthing right you don't need a Lee FCD.
Seat and crimp in two seperate steps and if you are getting too much crimp, adjust your dies so it doesn't do it as much.
On a single stage press I use the seat/crimp die to do both steps seperately. On a progressive I usually use a standard Lee seat/crimp die to perform the crimp operation after the bullet was seated in a previous step.
|
I concur. I seat and crimp in separate steps using a three die set as well. I have a spare lock ring that I add to my seat/crimp die. It acts as a spacer. I add it, then set my seating depth with a dummy round I keep for the purpose. I then seat my rounds. Afterwards, I remove the extra lock ring off the bottom and crimp.
Chubbs
|
02-12-2012, 12:06 PM
|
|
Member
|
|
|
Join Date: Feb 2008
Location: Florida
Posts: 22,082
Likes: 10,795
Liked 15,509 Times in 6,796 Posts
|
|
Quote:
Originally Posted by Fishslayer
^^^This. Especially the last part...
Actually I believe Dillon does make a taper crimp die. I could be wrong....
EDIT: Aha! From Big Blue's website...
|
Yes, but does it fully resize (post size) or just crimp?
__________________
Still Running Against the Wind
|
02-12-2012, 12:48 PM
|
|
Member
|
|
|
Join Date: Aug 2010
Location: C-Bus
Posts: 6,335
Likes: 4,311
Liked 4,916 Times in 2,086 Posts
|
|
I did these on my Dillon last night. 230 gr Berry's plated. I don't know how the taper crimp is classified but this is what they look like.
|
02-17-2012, 12:26 PM
|
Member
|
|
|
Join Date: Aug 2011
Location: S.W. Mississippi
Posts: 10
Likes: 0
Liked 1 Time in 1 Post
|
|
taper crimp
Quote:
Originally Posted by Fishslayer
^^^This. Especially the last part...
Actually I believe Dillon does make a taper crimp die. I could be wrong....
EDIT: Aha! From Big Blue's website...
|
My dillon pumps out beautiful 45 ACP ammo for quite a few years now. It taper crimps the cases in the 4th stage. Also does a fine job on shorty forties as well......... Have a new question re loading 45 auto rim for my old 1917 Smith and Colt. Are the loads the same as 45 ACP while keeping the pressures low ??
|
02-17-2012, 12:42 PM
|
Member
|
|
|
Join Date: Oct 2010
Location: Ramona, CA
Posts: 236
Likes: 2
Liked 4 Times in 4 Posts
|
|
Quote:
Originally Posted by palmetto99
Ok, I seem to be having a little trouble getting my sizing correct for plated 230grn round noce 45acp and was wondering if a 4-die set might work a little better. The brass cuts into the bullet. I don't seem to have a problem with FMJ in 45acp (or 9mm) when using the 3-die set.
Using a single stage RCBS.
What are most folks using with a single stage.
Thank you all.
|
Are you getting shavings of the plating or are you getting a cut ring through the plating around the bullet at the top of the case? These symptoms are caused by different things.
Cut ring through plating is caused by applying TOO MUCH crimp. Readust your current die accordingly and you're good to go.
Shaving the plating off as the bullet is inserted could be caused by too little flare as noted, but can also be caused by improper adjustment of the seater/crimp die.
You indicate you have no problems with FMJ, so I think some minor adjustment of your current seater/crimp die should solve your issues. I separate the seating and crimping operations, but still have to make minor adjustments when crimping plated vs. FMJ bullets, and when loading different brass headstamps.
__________________
S&W15-22 RIA 1911
CZ75B SR9
|
|
Posting Rules
|
|
|
|
|