Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 10-31-2012, 03:40 PM
Challenger44 Challenger44 is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Oct 2012
Posts: 4
Likes: 0
Liked 0 Times in 0 Posts
Default reloading 9mm & 357 sig

I reload for both 9mm and 357 sig. When I try using the 124gr 9mm bullet in my 357 sig round I have a problem with powder compression and the powder pushes the bullet back up. If I use the 125gr speer bullet everything works fine. Should I not be using the 124gr bullet for the 357 sig?
Reply With Quote
  #2  
Old 10-31-2012, 03:51 PM
venomballistics's Avatar
venomballistics venomballistics is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Aug 2007
Location: between beers
Posts: 8,873
Likes: 4,772
Liked 6,925 Times in 3,301 Posts
Default

first, there is no "The" 124G 9MM bullet, there are many.
odds are you are just using one that differs from the one in your data.
__________________
it just needs more voltage
Reply With Quote
  #3  
Old 10-31-2012, 04:49 PM
Challenger44 Challenger44 is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Oct 2012
Posts: 4
Likes: 0
Liked 0 Times in 0 Posts
Default

I'm using Speer 124gr HP and Speer 125gr HP. Following my reloading data to the T. The 125gr has a more concave base which I believe allows for proper insertion to maintain COL. The flatter 124gr base is compressing the powder and pushes the bullet back up.
Reply With Quote
  #4  
Old 10-31-2012, 04:59 PM
venomballistics's Avatar
venomballistics venomballistics is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Aug 2007
Location: between beers
Posts: 8,873
Likes: 4,772
Liked 6,925 Times in 3,301 Posts
Default

where the 125 HP is a 357 rather than a 9MM ... right?
look at the cavities.
in order to expand at the lower velocities of the 9MM the cavity is going to be a little wider and a little deeper than what is needed in a 357 HP at magnum velocities. that material taken out of the nose had to be put somewhere. That makes a longer bullet.
I take it you are trying to sub in this 124 over a load you have developed for the 125 ... I strongly suggest you drop back to the minimum charge and start over.
__________________
it just needs more voltage
Reply With Quote
  #5  
Old 10-31-2012, 06:47 PM
Coastie762's Avatar
Coastie762 Coastie762 is offline
US Veteran
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Jan 2007
Location: N.E. Wisconsin
Posts: 622
Likes: 965
Liked 1,137 Times in 339 Posts
Default

The Sig has a rather short case neck. Round nose, long ogive bullets meant for the 9x19 or the .38 Super have a relatively short bearing surface. Depending on the bullet you are using, there may not be much of the bullet actually contacting the case neck. These are not considered safe for loading the Sig as they may be pushed back into the case during the loading cycle, causing excessive pressures.

The 125 grain Speer Gold Dot designed for the Sig has a proper length full diameter bearing surface. Other bullets that work well for the Sig are the Hornady 124 gr XTP and 125 gr HAP. Both work well in my .357 Sig loads as well as the Speer GD you mentioned above.
Reply With Quote
The Following User Likes This Post:
  #6  
Old 10-31-2012, 07:14 PM
firecracker6 firecracker6 is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Apr 2011
Location: kansas city
Posts: 56
Likes: 0
Liked 6 Times in 5 Posts
Default

I think you're getting good advice. I think you're stuck w/ conical bullets w/ this round. By any chance is the 124gr bullet longer than the 125gr one?
Reply With Quote
  #7  
Old 10-31-2012, 07:59 PM
Challenger44 Challenger44 is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Oct 2012
Posts: 4
Likes: 0
Liked 0 Times in 0 Posts
Default

I used a micromiter to check the length of both and they were the same. I'm just curious if anybody else has had this problem using bullets designed for the 9mm and not specifically for the 357 sig.
Reply With Quote
  #8  
Old 11-01-2012, 07:21 AM
Coastie762's Avatar
Coastie762 Coastie762 is offline
US Veteran
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Jan 2007
Location: N.E. Wisconsin
Posts: 622
Likes: 965
Liked 1,137 Times in 339 Posts
Default

Attached is a photo showing a Speer .357 Sig 125 grain Gold Dot and a generic 9mm 124 grain round nose alongside a Sig case. Also included is a 9mm 124 grain Hornady XTP-HP and 125 grain HAP alongside a loaded round with the XTP. The truncated cone shapes of the Hornady and Speer bullets incorporate a long full length bearing surface that provides proper neck tension.

None of the major reloading manuals recommend using standard 9mm round nose bullets with the Sig case due to their shape and possible lack of proper neck tension.
Attached Images
File Type: jpg 357 Sig.jpg (113.6 KB, 774 views)

Last edited by Coastie762; 11-01-2012 at 06:09 PM.
Reply With Quote
The Following User Likes This Post:
  #9  
Old 11-01-2012, 03:21 PM
firecracker6 firecracker6 is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Apr 2011
Location: kansas city
Posts: 56
Likes: 0
Liked 6 Times in 5 Posts
Default

I think the Coastie's got it right.
Reply With Quote
  #10  
Old 11-02-2012, 06:06 AM
blujax01's Avatar
blujax01 blujax01 is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Aug 2010
Location: C-Bus
Posts: 6,335
Likes: 4,311
Liked 4,916 Times in 2,086 Posts
Default

To echo, my Speer manual has a separate section on 357 sig and cautions against using "just any" 9mm bullet because of the symptoms you mentioned. They recommend their Gold Dot 125 grain JHP #4360.
Reply With Quote
  #11  
Old 11-02-2012, 07:23 AM
Coastie762's Avatar
Coastie762 Coastie762 is offline
US Veteran
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Jan 2007
Location: N.E. Wisconsin
Posts: 622
Likes: 965
Liked 1,137 Times in 339 Posts
Default

A couple more photos to flog the horse some more.

I got bored last night and took the 124 grain 9mm RN, blackened it with a sharpie and loaded it into a resized WW .357 Sig case to my normal "load to" length. I then used a knife to mark the location of the case mouth on the bullet. Next, the bullet was extracted using a kinetic puller (one whack) and measured to get the bullet diameter at the mark, as well as where the contact marks started and where the bullet reached its full .355" diameter.

The expander ball diameter is .353". From my readings, the full .355 bullet diameter was at or below the shoulder of the case. The diameter at the case mouth was .345". The diameter of the bullet at contact with the case neck was .353". Essentially no neck tension. If this had been a loaded round and chambered, the bullet would have likely set back and a potentially dangerous high chamber pressure would have been the result.
Attached Images
File Type: jpg Sig 2.jpg (82.7 KB, 410 views)
File Type: jpg Sig 3.jpg (104.0 KB, 359 views)
Reply With Quote
  #12  
Old 11-02-2012, 03:29 PM
Challenger44 Challenger44 is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Oct 2012
Posts: 4
Likes: 0
Liked 0 Times in 0 Posts
Default

Coastie762,

This is great information and exactly what I was looking for. Thank you for putting this together, It is a huge help. I will stick with using the Speer 125gr. Gold Dot as recommended.

Thank you!
Reply With Quote
  #13  
Old 11-02-2012, 05:23 PM
Coastie762's Avatar
Coastie762 Coastie762 is offline
US Veteran
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Jan 2007
Location: N.E. Wisconsin
Posts: 622
Likes: 965
Liked 1,137 Times in 339 Posts
Default

You are very welcome. Good shooting!
Reply With Quote
  #14  
Old 11-02-2012, 05:34 PM
perrazi perrazi is offline
Absent Comrade
 
Join Date: Jan 2009
Posts: 2,998
Likes: 845
Liked 898 Times in 488 Posts
Default

you can also use remington 124hp and nosler 9mm hp. they will also work. have been using them since the 357 sig first came out. none of the round nose bullets will work.
Reply With Quote
  #15  
Old 09-28-2013, 10:29 PM
twall68 twall68 is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Sep 2013
Posts: 1
Likes: 0
Liked 0 Times in 0 Posts
Default X-Treme bullets

If your looking for good bullets for reloading .357 sig ammo try X-treme's 124gr FP bullets. I've been using them without problems. Their prices include shipping!

X-Treme Bullets the finest hard-cast bullets and plated bullets money can buy
Reply With Quote
  #16  
Old 09-29-2013, 11:55 AM
fredj338's Avatar
fredj338 fredj338 is offline
Member
 
Join Date: Feb 2006
Location: Kalif. usa
Posts: 6,836
Likes: 2,665
Liked 3,927 Times in 2,366 Posts
Default

Not all 9mm bullets will work for the sig but all 357sig bullets will work for the 9mm. The 357sig needs a bullet with long bearing surface & short nose. Most truncated cone shaped bullets will work, regardless fo weight. I have load 88gr to 147gr in my 357sigs. lead, plated & jacketed..
__________________
NRA Cert. Inst. IDPA CSO
Reply With Quote
  #17  
Old 09-29-2013, 02:18 PM
SMSgt's Avatar
SMSgt SMSgt is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Jul 2010
Location: Florida
Posts: 6,555
Likes: 3,343
Liked 9,152 Times in 3,432 Posts
Default

The case neck of the .357 SIG is short, having a longer "bearing surface" on the bullet is irrelevant if it isn't contacting the case neck. A longer bearing surface will allow for a longer COL, provided your mag, chamber, and feeding will allow.
Reply With Quote
  #18  
Old 09-29-2013, 05:11 PM
scooter123 scooter123 is offline
Member
 
Join Date: Jan 2009
Location: Metro Detroit, Michigan
Posts: 6,919
Likes: 179
Liked 4,294 Times in 2,106 Posts
Default

IMO a simple and likely much LESS costly solution may be to just load the 9mm bullet to a longer overall length. That will solve the powder compression issue AND get the Driving Diameter of the bullet up into the case neck where it needs to be for proper neck tension. The only question is whether that longer required length will chamber correctly in your barrel.

That is a test that you'll have to do yourself but that's dead simple, field strip your pistol and drop an assembled dummy at the new length into your chamber and see if it seats fully in the chamber. BTW, it should come out freely by just tipping the barrel, if it hangs up that's an indication that you are too long. If your bullet is just barely snagging on the rifling shorten your dummy up by 0.005 inch and see how that fits. It's also a good idea to mark the point where the bullet just starts to taper down and check to confirm that mark is in FRONT of the edge of the case, by doing that you can confirm that your full diameter bearing surface is engaged in the case neck.
Reply With Quote
  #19  
Old 09-29-2013, 10:50 PM
HCH HCH is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Jan 2012
Location: Hancock County Ohio
Posts: 710
Likes: 2,507
Liked 525 Times in 235 Posts
Default

Change your powder.
Reply With Quote
  #20  
Old 09-29-2013, 11:16 PM
colt_saa's Avatar
colt_saa colt_saa is offline
SWCA Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Feb 2005
Location: Cocoa Beach, Florida
Posts: 10,559
Likes: 3,037
Liked 22,450 Times in 5,824 Posts
Default

Many 9MM and 380 projectiles work fine with the 357SIG, but not all.

The Lee FCD is a fantastic tool for use with projectiles that have a short bearing surface. It makes it possible to load the 88 grain JHPs to 1700 FPS from my P229 Sport.
Reply With Quote
  #21  
Old 09-30-2013, 02:20 AM
fredj338's Avatar
fredj338 fredj338 is offline
Member
 
Join Date: Feb 2006
Location: Kalif. usa
Posts: 6,836
Likes: 2,665
Liked 3,927 Times in 2,366 Posts
Default

Quote:
Originally Posted by SMSgt View Post
The case neck of the .357 SIG is short, having a longer "bearing surface" on the bullet is irrelevant if it isn't contacting the case neck. A longer bearing surface will allow for a longer COL, provided your mag, chamber, and feeding will allow.
Not really. A short bearing surface, as in most RN bullets, means you have less bullet to contact the short neck, less adjustment for proper OAL. So yes, length of the bearing surface has a lot to do with proper bullet choice in the 357sig, as well as the nose shape.
__________________
NRA Cert. Inst. IDPA CSO
Reply With Quote
  #22  
Old 09-30-2013, 07:31 PM
Wee Hooker Wee Hooker is offline
Member
reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig reloading 9mm & 357 sig  
Join Date: Mar 2003
Location: New England, USA
Posts: 4,468
Likes: 3,068
Liked 4,294 Times in 1,610 Posts
Default

As mentioned, not all 9mm bullets are a good choice. I use ( Mossourri's) 125gr TC shaped 38 super bullets in my 357 sig loads and they work great. The secret is that while the bullet has the same weight and diameter as a 9mm bullet, more of that weight is forward in the shoulder. These same bullets will NOT load in a 9mm because they sit to deep in that case.
__________________
Dave
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Reloading the .40 S&W epj Reloading 42 11-17-2017 05:02 PM
Hodgdon Reloading Data Center VS Hornady Reloading Handbook gsparesa Reloading 48 02-10-2013 04:50 PM
Reloading 38/357 PARTSGUY53 Reloading 8 01-19-2013 02:54 PM
reloading the 12 Ga. Nevada Ed Reloading 2 01-17-2013 10:44 PM
Need help with reading the reloading chart in Lee's Modern Reloading book Gorenut Reloading 20 11-28-2012 11:51 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 07:38 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)