Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 12-05-2012, 09:01 PM
tappedandtagged tappedandtagged is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Oct 2011
Posts: 397
Likes: 147
Liked 110 Times in 67 Posts
Default 30-30 loads

I'm looking for a good 30-30 load for large hogs. My last encounter yeilded a 200+- hog from my .270. The 130 grain Nosler Accubond bullet didn't fully exit. I found it sticking out 1/16" from the off side hog sheild.

My gun shoots 159 grn Rem Core Lokts well. Sub 2 MOA with the buckhorn sights. Since I will be night huntng, I will likely scope this gun and mount a good spotlight on the scope (legal on private land in AR).

I have H335 and W748 on hand. I am not opposed to getting another powder. I would like to duplicate factory velocities since the 30-30 is already a "slow" caliber. Any reccomendations for powder/bullets will be appreciated. I am leaning heavily toward jacketed bullets, but am considering cast. The bonded Speer Deep Curl line has aught my attention. Not certain if I want to deviate from the standard 150 grain bullet either.

The rifle is a mid '70s pre-saftey 336 passed down from my father. I have yet to harvest any animal with it.

So, suggestions on powders? Bullets? Any pics of recovered bullets would be much appreciated.

ETA: I wasn't clear before. I thought I had put this in here, but when I editted it or a shorter post, I guess I took it out inadvertently. I love my .270 and it performs well on hogs. But it is not a very ady gun for carrying a lot at night in thick stuff. I had been using my AR-15 but when I saw that my .270 didn't even produce a full exit wound, it made me feel very leary about going to the woods with only a .223. Thus my search for a 30-30 load. I have a 336 which I find balances very well and offers much quicker handling over my .270 bolt rifle.

Last edited by tappedandtagged; 12-07-2012 at 04:07 AM.
Reply With Quote
  #2  
Old 12-05-2012, 10:42 PM
358156hp 358156hp is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Dec 2011
Location: Nebraska
Posts: 728
Likes: 97
Liked 224 Times in 149 Posts
Default

170 gr bullets should penetrate deeper. Don't let the velocity difference deceive you. I've talked with a few guys in the past who have hunted elk with a 30/30, and they used 170 gr bullets. You can still get some pretty trick bullets for the 30/30 if you feel the need.
Reply With Quote
The Following User Likes This Post:
  #3  
Old 12-05-2012, 11:05 PM
alwslate alwslate is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Dec 2009
Location: Indiana
Posts: 6,606
Likes: 3,693
Liked 7,174 Times in 2,997 Posts
Default

If you read a few reloading manuals you will see that either powder
can be used to equal factory velocities with 170 gr bullets.
Reply With Quote
  #4  
Old 12-05-2012, 11:17 PM
TNDave TNDave is offline
Member
 
Join Date: May 2005
Posts: 1,063
Likes: 310
Liked 405 Times in 105 Posts
Default

I am a big fan of 32.0 of Varget under a 170 grain Sierra ProHunter. I have killed a lot of critters with that load and it shoots well out of every gun I ever tried it in. This hog agrees. He was walking toward me at about 85 yards. The round went in behind his ear and coursed down through his body. No exit. He fell over at the shot. No attempt to get up. A couple kicks. He looks little but was 205 lbs.


Last edited by TNDave; 12-05-2012 at 11:20 PM.
Reply With Quote
  #5  
Old 12-05-2012, 11:42 PM
tappedandtagged tappedandtagged is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Oct 2011
Posts: 397
Likes: 147
Liked 110 Times in 67 Posts
Default

Quote:
Originally Posted by TNDave View Post
I am a big fan of 32.0 of Varget under a 170 grain Sierra ProHunter. I have killed a lot of critters with that load and it shoots well out of every gun I ever tried it in. This hog agrees. He was walking toward me at about 85 yards. The round went in behind his ear and coursed down through his body. No exit. He fell over at the shot. No attempt to get up. A couple kicks. He looks little but was 205 lbs.

Ever shoot one through the shield with that load?
Reply With Quote
  #6  
Old 12-06-2012, 12:19 AM
Zappa's Avatar
Zappa Zappa is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Dec 2012
Location: Eastern Mass
Posts: 37
Likes: 6
Liked 3 Times in 3 Posts
Default

Quote:
Originally Posted by tappedandtagged View Post
I'm looking for a good 30-30 load for large hogs. My last encounter yeilded a 200+- hog from my .270. The 130 grain Nosler Accubond bullet didn't fully exit. I found it sticking out 1/16" from the off side hog sheild.
This is exactly what you want to happen.
If the bullet fully exits, it means it's still carrying energy.
And if it's still carrying energy, it means it didn't transmit all it's energy into the target.
The optimum condition is for the bullet to dump all it's energy into the target.
Reply With Quote
  #7  
Old 12-06-2012, 03:55 AM
tappedandtagged tappedandtagged is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Oct 2011
Posts: 397
Likes: 147
Liked 110 Times in 67 Posts
Default

Quote:
Originally Posted by Zappa View Post
This is exactly what you want to happen.
If the bullet fully exits, it means it's still carrying energy.
And if it's still carrying energy, it means it didn't transmit all it's energy into the target.
The optimum condition is for the bullet to dump all it's energy into the target.
Yes, but the fact that a .270 won't exit made me realize that my .223 was way under gunned. Thats why I'm moving up to a 30-30 as my night hunting gun.

And I would really rather have an exit wound. Hogs bleed very little as it is. An exit would would double my sucess in tracks in the event of a run off.
Reply With Quote
  #8  
Old 12-06-2012, 03:57 AM
ArchAngelCD's Avatar
ArchAngelCD ArchAngelCD is offline
Moderator
SWCA Member
Absent Comrade
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
Default

Because of that tough plate they walk around with I would suggest using a 170gr Premium bullet along with Leverevolution powder.

Some good bullets are the Hornady InterLock (#3060), Sierra Pro-Hunter (#2010), Nosler Partition (#16333), Speer DeepCurl (#2042), or even the Swift A-Frame (#301701) if you can afford them. (I can't) The premium bullet will resist expanding when they hit the plate and penetrate deep enough to do damage and stop the Hog.
__________________
Freedom is never free!!
SWCA #3437
Reply With Quote
  #9  
Old 12-06-2012, 07:10 AM
olskool's Avatar
olskool olskool is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Jan 2011
Location: the woods of S.C.
Posts: 538
Likes: 2,460
Liked 1,278 Times in 255 Posts
Default

you most likely don't need another powder. h335 is one of the best powders you can use in a 30-30 every one i have used it in shot small groups with high speed.
Reply With Quote
  #10  
Old 12-06-2012, 08:01 AM
TNDave TNDave is offline
Member
 
Join Date: May 2005
Posts: 1,063
Likes: 310
Liked 405 Times in 105 Posts
Default

Quote:
Originally Posted by tappedandtagged View Post
Ever shoot one through the shield with that load?
No. The neck/ear shot is the shot I am always going for.
Reply With Quote
  #11  
Old 12-06-2012, 06:23 PM
tappedandtagged tappedandtagged is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Oct 2011
Posts: 397
Likes: 147
Liked 110 Times in 67 Posts
Default

Great! If readily available locally, I want to use the Speer deep curl. If not, I know I can find the Sierra. I will experiment with the H335 and W748. If I like one of thise, I will stop. If not, LeverEvolution will be the next one I try.
Reply With Quote
  #12  
Old 12-06-2012, 07:30 PM
DWalt's Avatar
DWalt DWalt is online now
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,481
Likes: 236
Liked 28,945 Times in 14,014 Posts
Default

The original .30-30 load used a 170 grain bullet and 30 grains (the second 30) of a propellant ballistically much like IMR 3031. That is still a good load. If you want to reload .30-30 using spitzer bullets, you can. But if so, is safest to load one round in the chamber and one in the magazine. The old story about igniting cartridges with spitzer bullets in a tubular magazine under recoil is mainly a myth. Many tests have shown it does not happen.
Reply With Quote
  #13  
Old 12-06-2012, 08:00 PM
Chop's Avatar
Chop Chop is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Jan 2003
Location: Wyoming/Alabama
Posts: 492
Likes: 88
Liked 287 Times in 88 Posts
Default

I shot several hogs in NC using factory 170grain core-locks. Never had one get away.

Chop
__________________
MSG US Army
Reply With Quote
  #14  
Old 12-06-2012, 08:12 PM
Nevada Ed's Avatar
Nevada Ed Nevada Ed is offline
US Veteran
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Nov 2012
Location: Reno Nv
Posts: 13,376
Likes: 3,183
Liked 12,712 Times in 5,669 Posts
Default

You can't beef up the old 30-30 too much from the factory velositys but the thing you can do is find a load that is.......
Accurate "Dead on" with your reloads.

Thats what is so great about reloading................even if you have to be 150fps slower than factory...........and another vote for the 170gr JFP bullet for maximum penetration.

Hornady 100gr plinker for "Wabbit".


Last edited by Nevada Ed; 12-06-2012 at 09:01 PM.
Reply With Quote
  #15  
Old 12-06-2012, 08:21 PM
samdweezel05 samdweezel05 is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Nov 2011
Posts: 57
Likes: 25
Liked 30 Times in 5 Posts
Default

160gr Hornady FTX over 30.2gr of IMR 4064. That load puts 3 shots under 2" at 100yds with my iron sight 1955 M94. Good luck.



Reply With Quote
  #16  
Old 12-06-2012, 09:17 PM
dla dla is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Feb 2010
Posts: 1,100
Likes: 326
Liked 468 Times in 278 Posts
Default

Quote:
Originally Posted by tappedandtagged View Post
I'm looking for a good 30-30 load for large hogs. My last encounter yeilded a 200+- hog from my .270. The 130 grain Nosler Accubond bullet didn't fully exit. I found it sticking out 1/16" from the off side hog sheild.

My gun shoots 159 grn Rem Core Lokts well. Sub 2 MOA with the buckhorn sights. Since I will be night huntng, I will likely scope this gun and mount a good spotlight on the scope (legal on private land in AR).

I have H335 and W748 on hand. I am not opposed to getting another powder. I would like to duplicate factory velocities since the 30-30 is already a "slow" caliber. Any reccomendations for powder/bullets will be appreciated. I am leaning heavily toward jacketed bullets, but am considering cast. The bonded Speer Deep Curl line has aught my attention. Not certain if I want to deviate from the standard 150 grain bullet either.

The rifle is a mid '70s pre-saftey 336 passed down from my father. I have yet to harvest any animal with it.

So, suggestions on powders? Bullets? Any pics of recovered bullets would be much appreciated.
So lets see, you're standing there examining a dead hog and you decide you need a different cartridge and bullet?

If you want more penetration, slow down the bullet.

If you want more fun tracking at night use 30cal hardcast (seriously, it is a really bad choice for anything other than drilling little holes).

If you want BANG flop, then use a cheaper 130gr from your 270 and run it at 3000+fps. They don't have to penetrate very far to turn the insides of a piggy to mush.

I think the Speer 150gr FP is a good 30-30 bullet and you can run it at 2400fps from 20" tube.

My humble opinion of course
Reply With Quote
  #17  
Old 12-06-2012, 11:02 PM
tappedandtagged tappedandtagged is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Oct 2011
Posts: 397
Likes: 147
Liked 110 Times in 67 Posts
Default

Quote:
Originally Posted by dla View Post
So lets see, you're standing there examining a dead hog and you decide you need a different cartridge and bullet?

If you want more penetration, slow down the bullet.

If you want more fun tracking at night use 30cal hardcast (seriously, it is a really bad choice for anything other than drilling little holes).

If you want BANG flop, then use a cheaper 130gr from your 270 and run it at 3000+fps. They don't have to penetrate very far to turn the insides of a piggy to mush.

I think the Speer 150gr FP is a good 30-30 bullet and you can run it at 2400fps from 20" tube.

My humble opinion of course
The dead hog was taken with my deer rifle while I was deer hunting. I want to use my 30-30 for hunting hogs at night instead of my AR that I usually take. I don't want to go out specifically for hogs with my bolt action .270. It is too long and heavy for a lot of still hunting. And not nearly as maneuverable as my 30-30.

My .270 did a fine job and I love the gun for what it is, a stand gun for open fields or shooting lanes. My 30-30 is better suited for the quick paced spot (or usually hear) and stalk in the brush of hog hunting. I used to use my AR, but since seeing that my .270 wouldn't do a pass through shot, I have decided to up my caliber choice. And I was considering hard cast for the "break the shoulder bones" effect, but have since decided to use a bonded jacketed.
Reply With Quote
  #18  
Old 12-06-2012, 11:04 PM
tappedandtagged tappedandtagged is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Oct 2011
Posts: 397
Likes: 147
Liked 110 Times in 67 Posts
Default

Quote:
Originally Posted by Nevada Ed View Post
You can't beef up the old 30-30 too much from the factory velositys but the thing you can do is find a load that is.......
Accurate "Dead on" with your reloads.

Thats what is so great about reloading................even if you have to be 150fps slower than factory...........and another vote for the 170gr JFP bullet for maximum penetration.

Hornady 100gr plinker for "Wabbit".

Nice looking gun there! And I'm not really looking for beefed up velocities, but I do want factory velocity or close to it. I WILL NOT risk a high pressure load in this rifle. It can not be replaced. It was the first rifle my dad got after he married my mom. When he passed it down to me, it came with the original box of ammo (of course it was corroded and had green gunk around the case mouth). I have found it to have an excellent trigger pull (before they were lawyer-ized) and very accurate with factory 150 Core Lokts.

Last edited by tappedandtagged; 12-07-2012 at 04:13 AM.
Reply With Quote
  #19  
Old 12-07-2012, 03:54 AM
ArchAngelCD's Avatar
ArchAngelCD ArchAngelCD is offline
Moderator
SWCA Member
Absent Comrade
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
Default

Quote:
Originally Posted by olskool View Post
you most likely don't need another powder. h335 is one of the best powders you can use in a 30-30 every one i have used it in shot small groups with high speed.
I actually never tried H335 in the 30-30 but I did use 4895, IMR4064 and a lot of IMR3031. While I use to load most of my 30-30 ammo with IMR3031 once I tried Leverevolution it became my only 30-30 powder.

Hornady uses different formulations of Leverevolution powder specifically mixed for each caliber. The Leverevolution powder being marketed by Hodgdon is the powder formulation used in the 30-30. I can report higher velocities with it, it's very clean burning and produces accurate ammo. I'm using it with the Hornady FTX bullets, traditional Hornady and Sierra 150gr and 170gr 30-30 bullets and with 165gr Hard Cast bullets too. It's very rare I turn away from a powder I used for a long time but this one is a keeper...
__________________
Freedom is never free!!
SWCA #3437
Reply With Quote
The Following User Likes This Post:
  #20  
Old 12-07-2012, 04:33 AM
Nevada Ed's Avatar
Nevada Ed Nevada Ed is offline
US Veteran
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Nov 2012
Location: Reno Nv
Posts: 13,376
Likes: 3,183
Liked 12,712 Times in 5,669 Posts
Default

Thanks;
I also got this gun from my father and it is a "Looker" since that one bullet is around 45 years old and the gun has never been fired and the action opened maybe 20 times to get a check up and cleaning if needed.
However the other 94 has put a lot of meat in the ice box..............mostly from the bushy California where shots are from 20 feet, way out to 70 yards !!

Have yet to try the new Hodgdon powder but it has to be great stuff to get those higher velositys and be cleaner than the older powders. This company is really putting great stuff out for the shooters and reloaders the last ten years.
Reply With Quote
  #21  
Old 12-07-2012, 11:01 AM
SMSgt's Avatar
SMSgt SMSgt is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Jul 2010
Location: Florida
Posts: 6,556
Likes: 3,344
Liked 9,153 Times in 3,432 Posts
Default

I've never had any commercial .30-30 round not do its job. I think it's almost the ideal short- to mid-range cartridge. I'd think either the 150- or 170-grain bullets would do a hog in.

Several casting companies make a 165-grain flat nosed .30-30 bullet if you really want penetration.
Reply With Quote
  #22  
Old 12-07-2012, 03:47 PM
Buffalohunter60 Buffalohunter60 is offline
US Veteran
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Jul 2012
Location: South Tamworth NH/New Zea
Posts: 499
Likes: 445
Liked 552 Times in 253 Posts
Default

I have used the 30-30 witrh 170 grain coreLok on Buffalo and had no problem...one shot (side profile) through the heart and out the other side. I like the 30-30, I have never shot hogs but I bet it will do the job just fine. I am a firm believer in bullet placement.
Reply With Quote
  #23  
Old 12-07-2012, 04:31 PM
tappedandtagged tappedandtagged is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Oct 2011
Posts: 397
Likes: 147
Liked 110 Times in 67 Posts
Default

Quote:
Originally Posted by Buffalohunter60 View Post
I have used the 30-30 witrh 170 grain coreLok on Buffalo and had no problem...one shot (side profile) through the heart and out the other side. I like the 30-30, I have never shot hogs but I bet it will do the job just fine. I am a firm believer in bullet placement.
Buffalo huh? Well that should work for hogs then! As to shot placement, yes that is key. But I have shot large boars with my AR right in the shoulder and never as much as found a drop of blood. That sheild (bassically 1 inch plus of cartlitdge) stops .223 rounds in their tracks on those old buggers.

I'm hoping to find the 30-30 load to penetrate the shield, break the shoulder and pulverize the heart. On the bigger ones, I doubt I will get a pass through. My father in law even shot a 230 lb hog with his 300 win mag (180 grain Winchester Silvertips) and didn't get a pass through. Said the cup and core separated somewhere inside and he found the cup only sticking in the offside sheild.

These shield are tough!
Reply With Quote
  #24  
Old 12-07-2012, 04:55 PM
Arik Arik is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Jan 2012
Location: Outside Philadelphia Pa
Posts: 16,601
Likes: 7,342
Liked 17,200 Times in 7,303 Posts
Default

Has anyone tried Buffalo Bore?

Sent from my DROIDX using Tapatalk 2
Reply With Quote
  #25  
Old 12-09-2012, 02:38 AM
Zappa's Avatar
Zappa Zappa is offline
Member
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Dec 2012
Location: Eastern Mass
Posts: 37
Likes: 6
Liked 3 Times in 3 Posts
Default

Quote:
Originally Posted by DWalt View Post
The old story about igniting cartridges with spitzer bullets in a tubular magazine under recoil is mainly a myth. Many tests have shown it does not happen.
That may be true, but I'm not going to try it.
I load spitzers for .30-30's all the time, but I shoot them out of my Contenders and Savage bolt action.
I have a few model 94's too, but they only get round nose or flat points.
I've loaded some silly stuff in this caliber too, from 100 grain short jacket "plinkers" and 110 grain JHP's to 180 grain Nosler Partitions and Ballistic Tips.
To the OP, try some Nosler Partitions on those hogs, I'll bet you'll get the desired results.
Reply With Quote
  #26  
Old 12-09-2012, 02:57 AM
Nevada Ed's Avatar
Nevada Ed Nevada Ed is offline
US Veteran
30-30 loads 30-30 loads 30-30 loads 30-30 loads 30-30 loads  
Join Date: Nov 2012
Location: Reno Nv
Posts: 13,376
Likes: 3,183
Liked 12,712 Times in 5,669 Posts
Default

One of the old time tricks with the old 30-30 is to develope a load that is dead on at 200 yards with a spitzer boattail bullet in 150 or 165grains.............
You only get one shot,since the rest in the gun are round nose bullets made for the 30-30.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Are todays .38 +P loads closer to .357 loads? photoman Ammo 34 07-05-2016 11:07 PM
Recommendations? Easy 44 Special loads and Quality 22 LR loads dacoontz Ammo 19 05-30-2015 07:13 PM
645 loads power167 Reloading 0 01-06-2013 08:27 PM
300 loads CWH44300 Reloading 1 07-20-2010 01:42 AM
460 loads...440-460gr loads marine247 Reloading 1 01-15-2009 10:27 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 09:42 PM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)