|
|
01-31-2013, 12:46 AM
|
Member
|
|
|
Join Date: Dec 2012
Location: PA
Posts: 30
Likes: 33
Liked 4 Times in 3 Posts
|
|
Reloading Bench
Ready to start reloading for my S & W wheel guns. Any suggestions on good sturdy premade reloading benches from sears, home depot, etc?
Thanks in advance.
|
01-31-2013, 12:56 AM
|
Member
|
|
|
Join Date: Feb 2010
Location: Kansas City area
Posts: 1,109
Likes: 161
Liked 518 Times in 169 Posts
|
|
I saw some wood ones advertised at Harbor Freight but haven't seen them in person.
__________________
Dick
|
The Following User Likes This Post:
|
|
01-31-2013, 01:53 AM
|
|
US Veteran
|
|
|
Join Date: Nov 2012
Location: Reno Nv
Posts: 13,405
Likes: 3,189
Liked 12,771 Times in 5,690 Posts
|
|
Just make sure that it is sturdy and well made.........not the cheap china stuff with small screws and bolts and partical board.
Working a press can break a table down if not well supported from the up and down motion day in and day out, no matter how slight.
|
The Following User Likes This Post:
|
|
01-31-2013, 02:38 AM
|
Member
|
|
|
Join Date: Apr 2005
Location: Idaho Territory
Posts: 57
Likes: 75
Liked 5 Times in 5 Posts
|
|
If you construct a loading bench yourself, do not make it any deeper than 20 to 24 inches. If it is any deeper it will become a catch all for everything in your loading room. I am currently living with the consequences of a bench top that is too deep, mine is 48 x 96 inches. It is so easy to get yourself buried in reloading clutter. Keep it simple.
|
The Following User Likes This Post:
|
|
01-31-2013, 07:21 AM
|
Member
|
|
|
Join Date: Feb 2010
Location: Buffalo WY
Posts: 423
Likes: 307
Liked 90 Times in 53 Posts
|
|
I have one of these Beechwood,rock solid, I have taken mine apart and moved 4 times.More versatile than a typical wood work bench, I also do engraving on this bench really nice to work on/with.I wanted something that was near furniture quality as it was going in my house. I have tried to upload a few more pictures of the shelf, cabinet and drawers with no luck. Worth every penny I paid for it. www.woodcraft.com has them.
IMG_0432.IMG_0432.jpg
Last edited by longranger; 01-31-2013 at 07:50 AM.
|
The Following 2 Users Like Post:
|
|
01-31-2013, 07:55 AM
|
|
Member
|
|
|
Join Date: Aug 2010
Location: C-Bus
Posts: 6,335
Likes: 4,311
Liked 4,916 Times in 2,086 Posts
|
|
I started with a 4x8x3/4 sheet of oak plywood. I cut it to 2x8 and glued and screwed it together, used 1x2 trim on the edge, then attached it to a kitchen base cabinet as well as lagging it to the wall studs. Less than $100. Then things got a little crazy...
IMG 0653 - YouTube
|
The Following 5 Users Like Post:
|
|
01-31-2013, 09:05 AM
|
Banned
|
|
|
Join Date: Sep 2005
Posts: 509
Likes: 5
Liked 109 Times in 58 Posts
|
|
Never underestimate the power of multi-layered plywood.
|
The Following User Likes This Post:
|
|
01-31-2013, 10:59 AM
|
Member
|
|
|
Join Date: Dec 2009
Location: Northeast Ohio
Posts: 4,273
Likes: 3,043
Liked 1,791 Times in 932 Posts
|
|
Google Americanworkbench.com
John Sirpola has a variety of nice benches, located in S.C.
__________________
NRA Pistol/Rifle Inst. RSO
|
01-31-2013, 12:47 PM
|
|
US Veteran
|
|
|
Join Date: Aug 2006
Location: West Central IL
Posts: 22,803
Likes: 18,552
Liked 22,422 Times in 8,276 Posts
|
|
5/8" plywood with a 1/4" tempered Masonite top glued on, over 2X4 framework (on edge), and set over base cabinets and bolted to the wall studs.
__________________
H Richard
SWCA1967 SWHF244
|
01-31-2013, 12:58 PM
|
|
Member
|
|
|
Join Date: Dec 2012
Location: Santa Fe, NM
Posts: 62
Likes: 18
Liked 29 Times in 19 Posts
|
|
built this last year, 2 layers of 1/2" ply (it's what i had laying around), topped with laminate (keeps it easy to clean up), set on a pair of drawer units, front reinforced with 4x4 glued and screwed to top. top screwed to drawer units. 30" high, 24" deep, 48" long. trimmed the front edge with 1"x1" aluminum angle (glued and screwed, with construction glue). free standing shelf for more stuff storage. you'll have to chisel a little of the 4x4 away for the press to clear. works great.
also, get a good light with magnifier ($19 at Michaels). and a comfy chair. light added after pic was taken.
|
The Following 2 Users Like Post:
|
|
01-31-2013, 01:19 PM
|
Member
|
|
|
Join Date: Nov 2012
Location: Kansas
Posts: 17
Likes: 1
Liked 0 Times in 0 Posts
|
|
I went to sears and bought one. The table top is solid particle board about 1.75 inches thick. Came with a peg board back and a light ficture. Two big drawers and a bottum shelf. It works good and it sturdy.
|
01-31-2013, 06:10 PM
|
|
Member
|
|
|
Join Date: Jan 2013
Location: NC
Posts: 68
Likes: 78
Liked 62 Times in 32 Posts
|
|
I made my bench from an old office desk I pick up for $15 at the Habitat Restore. Back is made from and old entertainment center somebody put out beside the road near my house that was free. I plan to build a much nicer bench at some point but this will do for awhile.
|
The Following 2 Users Like Post:
|
|
01-31-2013, 10:28 PM
|
|
Member
|
|
|
Join Date: Oct 2011
Location: Marylandistan
Posts: 2,737
Likes: 218
Liked 396 Times in 174 Posts
|
|
I recycled a old government drafting table.
A close up of my reloading god.
__________________
Life is good!
Last edited by MDMarauder; 01-31-2013 at 10:31 PM.
|
The Following 3 Users Like Post:
|
|
02-01-2013, 06:16 AM
|
|
Member
|
|
|
Join Date: Aug 2010
Location: C-Bus
Posts: 6,335
Likes: 4,311
Liked 4,916 Times in 2,086 Posts
|
|
MDMarauder, I'm digging your mascot.
|
02-01-2013, 09:29 AM
|
Member
|
|
|
Join Date: Dec 2012
Location: PA
Posts: 30
Likes: 33
Liked 4 Times in 3 Posts
|
|
thank you for all the great posts. I was thinking of using 2 horses and buying a nice sturdy piece of formica as the surface. Impressed by the various benches posted !
|
The Following User Likes This Post:
|
|
02-01-2013, 10:30 AM
|
Member
|
|
|
Join Date: Feb 2012
Location: MA
Posts: 1,602
Likes: 2,387
Liked 1,945 Times in 854 Posts
|
|
The main thing is to eliminate any wobble when you crank the handle of the press or the powder measure. I've reloaded for years on a small tool stand made for a small saw or planer. The frame is rigid and the feet extend out past the width of the top. I've also used a B&D Workmate when I take my single-stage presses to our club for classes. I bolt the presses to a solid piece of oak, then C-clamp the wood to the Workmate. If you have room, an old steel office desk is plenty solid for home use.
|
The Following User Likes This Post:
|
|
02-01-2013, 04:06 PM
|
|
US Veteran
|
|
|
Join Date: Dec 2011
Location: WA.
Posts: 4,451
Likes: 4,510
Liked 4,492 Times in 2,190 Posts
|
|
I built this one out of 2x6 and some scrap wood I had laying around. The Top is finished plywood. Took about 3 hours to build. Probably about $100 in material. Solid as a Sherman tank. I found the plans on the net. Jim
Uploaded with ImageShack.us
__________________
That's just somebody talkin.
|
The Following User Likes This Post:
|
|
02-01-2013, 08:02 PM
|
Member
|
|
|
Join Date: Jun 2008
Location: Colorado
Posts: 76
Likes: 0
Liked 25 Times in 10 Posts
|
|
If possible, like several of the poster said lag it to the wall with some angle iron and screws. I also liked the looks of those adjustable shelfs that MDMarauder has,
|
02-01-2013, 08:11 PM
|
|
Member
|
|
|
Join Date: Dec 2012
Location: Santa Fe, NM
Posts: 62
Likes: 18
Liked 29 Times in 19 Posts
|
|
common themes: sturdy and you don't need a lot of space to reload. but shelves for storing things you aren't presently using are very handy.
|
02-01-2013, 08:12 PM
|
|
Member
|
|
|
Join Date: Dec 2012
Location: Santa Fe, NM
Posts: 62
Likes: 18
Liked 29 Times in 19 Posts
|
|
Quote:
Originally Posted by MDMarauder
A close up of my reloading god.
|
"give me your powder"
|
02-01-2013, 08:18 PM
|
|
Member
|
|
|
Join Date: Oct 2011
Location: Marylandistan
Posts: 2,737
Likes: 218
Liked 396 Times in 174 Posts
|
|
Quote:
Originally Posted by blujax01
MDMarauder, I'm digging your mascot.
|
Thanks, he words off squibs and over charges!
__________________
Life is good!
|
02-01-2013, 08:21 PM
|
|
Member
|
|
|
Join Date: Oct 2011
Location: Marylandistan
Posts: 2,737
Likes: 218
Liked 396 Times in 174 Posts
|
|
Quote:
Originally Posted by DAB
"give me your powder"
|
My powder cop.
__________________
Life is good!
|
The Following User Likes This Post:
|
|
02-01-2013, 11:59 PM
|
|
US Veteran
|
|
|
Join Date: Mar 2012
Location: Midwest
Posts: 597
Likes: 347
Liked 214 Times in 99 Posts
|
|
I picked up one made by Stack-On. It does a good job with my Dillon SDB press. Made of steel with a particle board top. It works for me.
|
The Following User Likes This Post:
|
|
|
Posting Rules
|
|
|
|
|