Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 04-01-2017, 04:56 PM
Drill Sergeant Drill Sergeant is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Jun 2014
Posts: 29
Likes: 1
Liked 12 Times in 8 Posts
Default Reloading the Shield

I realize that the factory says NO, but ammo is too expensive not to reload. My question is, has anyone reloaded lead or lead coated bullets successfully with the Shield 9mm?

Thanks for your input!
Reply With Quote
  #2  
Old 04-01-2017, 05:05 PM
dave201's Avatar
dave201 dave201 is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Dec 2015
Posts: 96
Likes: 45
Liked 103 Times in 38 Posts
Default

The factories err on the side of caution. Some people reload like they drive on the highway talking on a cellphone . Can you blame them
That aside
I load 7.2 grains 3N37 with 90 grain Speer HP out of a 3.5 inch barrel
Gives me 1501 fps across the trap.
Stick with jacket till you get them right . Lead is a different animal
I use lead, but they have gas checks made out of soda cans

Last edited by dave201; 04-01-2017 at 05:08 PM.
Reply With Quote
  #3  
Old 04-01-2017, 05:18 PM
Drill Sergeant Drill Sergeant is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Jun 2014
Posts: 29
Likes: 1
Liked 12 Times in 8 Posts
Default It needs to handle lead well. . .

Quote:
Originally Posted by dave201 View Post
I use lead, but they have gas checks made out of soda cans
Soda cans? That's a new one on me. I love innovative people. Wow!

I already load for multiple calibers including 9mm. My current 9's eat both lead and jacketed very well, without gas checks. I am told that some do not. Recently, I have been loading coated bullets with success. Just want to be sure that the Shield works well with lead. If it doesn't, I won't consider a purchase.

Thanks fpor the feedback!
Reply With Quote
The Following User Likes This Post:
  #4  
Old 04-01-2017, 05:40 PM
epj's Avatar
epj epj is offline
US Veteran
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Dec 2005
Location: Birmingham, Alabama
Posts: 4,481
Likes: 227
Liked 2,397 Times in 1,081 Posts
Default

My particular Shield won't feed my lead reloads. All my other 9mms feed them without issue. This includes a couple of 1911's with "match chambers". I suspect this particular gun has a tight chamber, but haven't investigated further. It feeds factory ball ammo ok. Don't know about ball reloads, I've never made any. BTW, when I say it won't feed, what is actually does is not go fully into battery. Misses by about 1/8". Kinda spooks me, since I'm convinced that a Shield will fire slightly out of battery. Not 1/8" out, but enough out to rupture the case.

Last edited by epj; 04-01-2017 at 05:43 PM.
Reply With Quote
  #5  
Old 04-01-2017, 05:47 PM
ontargetagain ontargetagain is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Sep 2014
Location: North Central Ohio
Posts: 921
Likes: 862
Liked 597 Times in 332 Posts
Default

Well shortly I will know how my 45 Shield feeds plated SWC's or not. If not I will switch to plated FP or RN. I don't think I have ever bought a new box of ammo, may have gotten some in a trade with a gun
Karl
Reply With Quote
  #6  
Old 04-01-2017, 05:53 PM
Drill Sergeant Drill Sergeant is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Jun 2014
Posts: 29
Likes: 1
Liked 12 Times in 8 Posts
Default

Quote:
Originally Posted by ontargetagain View Post
Well shortly I will know how my 45 Shield feeds plated SWC's or not. If not I will switch to plated FP or RN. I don't think I have ever bought a new box of ammo, may have gotten some in a trade with a gun
Karl
Karl,

Does this mean that you already successfully load lead in your Shield; just not SWC?
Reply With Quote
  #7  
Old 04-01-2017, 05:59 PM
Garintheair Garintheair is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Jul 2013
Posts: 141
Likes: 201
Liked 85 Times in 42 Posts
Default

Quote:
Originally Posted by Drill Sergeant View Post
I realize that the factory says NO, but ammo is too expensive not to reload. My question is, has anyone reloaded lead or lead coated bullets successfully with the Shield 9mm?

Thanks for your input!
That's ALL I've fired in my .40 Shield, so far, other than a box of factory for function check. Not only that, but I have the PC Shield and you would think that lead bullets would decimate heaven and earth via the ports! Still no issues other than a bit more to clean properly.

I carry factory jacketed ammo but I only shoot lead reloads these days in all of my guns!
Reply With Quote
  #8  
Old 04-01-2017, 07:08 PM
gwpercle's Avatar
gwpercle gwpercle is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Nov 2011
Location: Baton Rouge, La.
Posts: 6,837
Likes: 7,387
Liked 8,045 Times in 3,651 Posts
Default

I do it all the time. For a Shield , Walther P38 , Springfield and Beretta 92F and a Ruger SR9. Even bought a Lee mould for $20.00 the Lee 356-120-TC just for the 9's , size them .357 .
It's takes a little trial and error to get several guns to all shoot 1 load well but if loading for only 1 it's easy.
Seating depth is about the only thing that require some back and forth, new guns don't have a long throat so the .357 part of the bullet has to be seated so it doesn't jamb into the rifling. If it jambs the slide wont close completely and getting the stuck round out is a bear .
Gary
Reply With Quote
  #9  
Old 04-01-2017, 07:35 PM
DumpStick DumpStick is offline
US Veteran
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Nov 2016
Location: Oklahoma, on a dirt road.
Posts: 389
Likes: 214
Liked 606 Times in 220 Posts
Default

Yep, me too.
Lee 358-125RF, sized to 358, NRA lube (50/50 beeswax/alox)
NOE 358-120TC, same, same.

Also shoot the Lee, tumble-lubed in 45/45/10.

Or, Berry's 124g FP, over RedDot for about 965fps. Nice easy shooting.

As stated earlier, OAL is the trick.
Reply With Quote
The Following User Likes This Post:
  #10  
Old 04-01-2017, 08:22 PM
Inyo Boy's Avatar
Inyo Boy Inyo Boy is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Mar 2017
Location: Western PA
Posts: 5
Likes: 1
Liked 1 Time in 1 Post
Default

I first started reloading with a Speer 124 gr. lead round nose using 3.6 grains of 700-X. The round functioned just fine in my 9mm shield and was accurate but that particular bullet leaded my barrel something awful. I switched to a 125 grain lead truncated cone bullet manufactured by Mastercast here in Western Pa with a BHN of 18 and had much better results. Same load of 700-X, just as acuurate, and still functions the Shield fine. Best of all, no leading. Anymore, I primarily shoot plated bullets, but still load the 125 lead t/c to have on hand when my pre teen son comes to shoot with me. He has a tendency to shoot rapid fire gangsta style and the lead rounds are cheaper to just blast away with.
Reply With Quote
  #11  
Old 04-01-2017, 09:41 PM
rwsmith's Avatar
rwsmith rwsmith is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Dec 2012
Location: (outside) Charleston, SC
Posts: 30,906
Likes: 41,494
Liked 29,147 Times in 13,778 Posts
Default Tons of lead and coated lead.....

I've shot lead and coated lead, fmjs, plated fmj, jacketed. No problems. My favorite is coated lead SWCs from Missouri. I won't buy any more coated lead 'small ball' stuff that is loaded to 1.06" OAL. They don't work well in any of my guns. Very frustrating. I finally got reliability up but it ain't near good enough to suit me.
__________________
"He was kinda funny lookin'"
Reply With Quote
  #12  
Old 04-02-2017, 09:52 PM
gsfxst gsfxst is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Apr 2011
Location: nebraska
Posts: 140
Likes: 2
Liked 12 Times in 9 Posts
Default

I ran 50, 115 hard lead round nose with 4.8 gr of Power Pistol in my Shield pro. they were very accurate .all feed with no problem. the lead build up was very bad around the ports on the barrel. And the inside of the slide had a lot of lead build up.
I haven't had any problem with jacketed bullets. that I reload. In the Pro. the lead bullets works fine in my High Power.
Reply With Quote
  #13  
Old 04-02-2017, 10:09 PM
ontargetagain ontargetagain is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Sep 2014
Location: North Central Ohio
Posts: 921
Likes: 862
Liked 597 Times in 332 Posts
Default

The factory warns against 'reloads' that are purchased that may have unknown variables that don't stay within SAAMI guidelines. If you are a competent reloader and stay within published guidelines there should be no issues. Lots of gun shows have vendors selling reloaded ammo, I am sure there are plenty of good ones and numerous poor ones.
Karl
Reply With Quote
  #14  
Old 04-05-2017, 03:16 PM
Nevada Ed's Avatar
Nevada Ed Nevada Ed is offline
US Veteran
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Nov 2012
Location: Reno Nv
Posts: 13,376
Likes: 3,183
Liked 12,712 Times in 5,669 Posts
Default

Gun makers do not want......

"Unchecked ammo" used in their weapons that have not passed
the PSI or CUP pressures c/o SAAMI standards.

They also mean careless loaders............

You just have to read between the lines.
Reply With Quote
  #15  
Old 04-06-2017, 08:48 AM
Lordvice's Avatar
Lordvice Lordvice is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Feb 2017
Posts: 62
Likes: 224
Liked 59 Times in 25 Posts
Default

I have a shield 45 and I shoot only my reloads with out a hitch. I load 200 swc hard cast and powder coated bullets. No issues.
Reply With Quote
  #16  
Old 04-06-2017, 09:32 AM
Zoner Zoner is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Jul 2010
Location: San Diego
Posts: 353
Likes: 48
Liked 258 Times in 114 Posts
Default

My 9mm Shield has about 500 rounds thru it....one box of factory FMJ, the rest my 124 gr RN lead reloads. I do the same thing with my Shield that i do with my 1911's. When it's time to seat bullets and crimp i disassemble the gun and keep the barrel handy. I "plunk test" every 10 rounds or so to make sure they'll chamber( i use a single stage press and only have one 9mm). If i had more than one 9mm i'd use the barrel with tightest chamber. You may also benefit loading cast to seat bullets then crimp as opposed to seating and crimping in one operation.....Mike
Reply With Quote
  #17  
Old 04-14-2017, 07:54 PM
Nevada Ed's Avatar
Nevada Ed Nevada Ed is offline
US Veteran
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Nov 2012
Location: Reno Nv
Posts: 13,376
Likes: 3,183
Liked 12,712 Times in 5,669 Posts
Default

With most pistol loads.........
a short or long case is not going to hurt that much........
since you are doing a taper crimp on the case........
and not a roll crimp on the bullet.

Now in a 38 or any revolver load putting a roll crimp on to a bullet
that has a cannelure or certain area to be crimped, a +/- case
could cause a slight problem.

I just think a lot of people "Big Deal" this +/- case thing.
Reply With Quote
The Following User Likes This Post:
  #18  
Old 04-17-2017, 12:48 AM
Thomas15 Thomas15 is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Mar 2006
Location: NE PA
Posts: 264
Likes: 75
Liked 150 Times in 95 Posts
Default

Can someone please explain to me how a handgun can tell the difference between a round of ammo that was made in a factory and one that was handloaded by a competent handloader?
Reply With Quote
  #19  
Old 04-17-2017, 02:50 AM
rwsmith's Avatar
rwsmith rwsmith is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Dec 2012
Location: (outside) Charleston, SC
Posts: 30,906
Likes: 41,494
Liked 29,147 Times in 13,778 Posts
Default Oh gosh yes...

I've reloaded jacketed, plated, plain cast, and several types of coatings and shoot them through all of my guns.

factory 9mm range ammo is pretty affordable unless you don't have any money.... like me.
__________________
"He was kinda funny lookin'"
Reply With Quote
  #20  
Old 04-17-2017, 02:56 AM
rwsmith's Avatar
rwsmith rwsmith is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Dec 2012
Location: (outside) Charleston, SC
Posts: 30,906
Likes: 41,494
Liked 29,147 Times in 13,778 Posts
Default Especially compact pistols...

Quote:
Originally Posted by epj View Post
My particular Shield won't feed my lead reloads. All my other 9mms feed them without issue. This includes a couple of 1911's with "match chambers". I suspect this particular gun has a tight chamber, but haven't investigated further. It feeds factory ball ammo ok. Don't know about ball reloads, I've never made any. BTW, when I say it won't feed, what is actually does is not go fully into battery. Misses by about 1/8". Kinda spooks me, since I'm convinced that a Shield will fire slightly out of battery. Not 1/8" out, but enough out to rupture the case.
In order to make ammo that will shoot in all of my guns, some bullets have to be seated more deeply to keep them from getting stuck on the lands of the barrel. Compact pistols don't have any room to spare between the chamber and the rifling.
__________________
"He was kinda funny lookin'"
Reply With Quote
  #21  
Old 04-17-2017, 03:01 AM
rwsmith's Avatar
rwsmith rwsmith is offline
Member
Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield Reloading the Shield  
Join Date: Dec 2012
Location: (outside) Charleston, SC
Posts: 30,906
Likes: 41,494
Liked 29,147 Times in 13,778 Posts
Default I load SWCs..

Quote:
Originally Posted by Drill Sergeant View Post
Karl,

Does this mean that you already successfully load lead in your Shield; just not SWC?
SWCs are my favorite lead bullet with all of my guns. But you have to seat them so that the shank of the bullet is only barely above the mouth of the case.

What I had a problem with was a type of RN lead called 'small ball'. Like normal RN bullets that have some taper to the ogive, these have to be seated to 1.06" MAX to be realiable or the bullets can hang up on the barrel lands. I had a problem with the coatings (bumpy) on some of those and I load them to 1.05" and still have a few hang ups. I'm not getting any more of those.

A RN lead bullet that is shaped like most jacketed bullets will give very little trouble. Some ramp polishing may help some feed better.
__________________
"He was kinda funny lookin'"

Last edited by rwsmith; 04-17-2017 at 03:03 AM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Anybody reloading for the Shield .45 MJS Smith & Wesson M&P Pistols 9 01-21-2017 12:49 PM
reloading for the shield buksul house Reloading 3 05-26-2015 07:08 PM
Reloading for a .40 M&P Shield Dirty-Sun Smith & Wesson M&P Pistols 6 06-13-2014 06:15 PM
Reloading for 9mm shield dead eye mike Reloading 5 03-25-2014 03:58 PM
SHIELD RELOADING J. R. WEEMS Reloading 5 04-22-2013 11:09 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 05:39 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)