Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 04-04-2017, 01:58 PM
Eddietruett Eddietruett is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Dec 2016
Location: South Carolina
Posts: 1,705
Likes: 1,049
Liked 3,510 Times in 957 Posts
Default Crimping Plated Bullets?

Picked up some Ranier plated 38 bullets. Sort of a swc style hp. Load in mind is 158 gr bullet with 5 gr Unique Powder. Question is how much crimp? I've heard that a tight crimp will "peel the plating off". No crimping groove so planned to seat with shoulder flush with case end like I do the Speer swaged swchp. Never tried coated so any suggestions or hints will be appreciated.
Reply With Quote
  #2  
Old 04-04-2017, 02:23 PM
H30 H30 is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Sep 2009
Location: Nevada
Posts: 134
Likes: 79
Liked 60 Times in 42 Posts
Default

I put a lite crimp on my plated bullets.
I have over crimped them before by quite a bit when setting up a die. When I pulled the bullets there was a deep grove in the bullets but no signs of breaking thru the platting. I think you would really have to over do it to cause damage.
Reply With Quote
  #3  
Old 04-04-2017, 02:34 PM
WR Moore WR Moore is offline
Member
 
Join Date: Oct 2006
Posts: 6,581
Likes: 1,788
Liked 5,342 Times in 2,685 Posts
Default

I use Berry and found that with some of them (specifically a 200 gr SWC .45), a stout taper crimp while seating was necessary to keep them from setting back in the feed cycle. Apparently, the plated bullet has less friction with the case than lead or jacketed. I guess it depends upon how thick your bullet supplier plates their product.

I've pulled a couple in various calibers and found a deep crimp, but no exposure of the core.
Reply With Quote
  #4  
Old 04-04-2017, 02:49 PM
gboling's Avatar
gboling gboling is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Aug 2008
Location: S/W Texas
Posts: 638
Likes: 261
Liked 232 Times in 132 Posts
Default

If they are roll crimped too tight it can cut their plating enough for the plating to come off in the barrel throat. Another round shoved down the pipe will plate the pipe with that copper. I can only imagine what multiples would do.

I would check the pipe after every round for a while.
Reply With Quote
The Following User Likes This Post:
  #5  
Old 04-04-2017, 03:13 PM
fredj338's Avatar
fredj338 fredj338 is offline
Member
 
Join Date: Feb 2006
Location: Kalif. usa
Posts: 6,836
Likes: 2,665
Liked 3,927 Times in 2,366 Posts
Default

Quote:
Originally Posted by WR Moore View Post
I use Berry and found that with some of them (specifically a 200 gr SWC .45), a stout taper crimp while seating was necessary to keep them from setting back in the feed cycle. Apparently, the plated bullet has less friction with the case than lead or jacketed. I guess it depends upon how thick your bullet supplier plates their product.

I've pulled a couple in various calibers and found a deep crimp, but no exposure of the core.
Are you loading 0.451" or 0.452"? A plated bullet is a lead bullet with a thin copper plating, so it is really more like a lead bullet & should be 0.001" larger than jacketed.
Yes, over crimping can damage the plating enough that during the high RPM spinning down the bbl, it can break off & accuracy goes to hell & you will get leading as well. Seen this many times on close targets where guys over crimp. You'll find little plating frags stuck in the paper & groups look more like patterns, even at 21ft.
__________________
NRA Cert. Inst. IDPA CSO
Reply With Quote
The Following User Likes This Post:
  #6  
Old 04-04-2017, 03:24 PM
Nevada Ed's Avatar
Nevada Ed Nevada Ed is offline
US Veteran
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Nov 2012
Location: Reno Nv
Posts: 13,376
Likes: 3,183
Liked 12,712 Times in 5,669 Posts
Default

With 5.0grs of Unique and a 158gr plated bullet..............
you will need some type of crimp to keep the bullets from walking, since it is near a maximum loading for a 38 case.
Reply With Quote
The Following 2 Users Like Post:
  #7  
Old 04-04-2017, 04:30 PM
hdwhit hdwhit is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Sep 2016
Location: North Texas
Posts: 804
Likes: 86
Liked 482 Times in 300 Posts
Default

I agree with H30, a light crimp on plated bullets is appropriate.

Like with any other change in components, you should follow the advice in the reloading manuals and drop back to minimum load, load a few cartridges and then function fire them before moving the load higher.

If you're like me and don't get to the range that often, you can load up, say five or ten rounds at minimum and then go up by 0.1 or 0.2 grains at a time loading five or ten each time putting them in clearly labeled containers abd then when you get to the range start with the lightest and work up until you see problems or reach maximum with no problems.
Reply With Quote
The Following User Likes This Post:
  #8  
Old 04-04-2017, 04:38 PM
gwpercle's Avatar
gwpercle gwpercle is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Nov 2011
Location: Baton Rouge, La.
Posts: 6,838
Likes: 7,394
Liked 8,051 Times in 3,652 Posts
Default

If they have a cannelure around the bullet , a light roll grimp, just enough to barely dig into the little cannelure indentations.

Plated seldom have a crimp groove for a heavy crimp.

If the bullets are smooth sided , a taper crimp is used , just enough to keep the bullets from walking out.

Gary
Reply With Quote
The Following User Likes This Post:
  #9  
Old 04-04-2017, 07:26 PM
robert1804 robert1804 is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Apr 2015
Location: austin tx
Posts: 310
Likes: 95
Liked 272 Times in 133 Posts
Default

I shoot lots of Rainier, Berry's and Xtreme plated in revolver and auto. I only taper crimp all of them, mainly to ease loading into revolvers. Case tension is the thing needed to prevent pulling or set-back. I have collected enough sizing and expander dies, including undersize sizers to get good case tension for everything I load. For 38 and 357, any sizer will do. I've found almost all expanders are too large for plated bullets. I took a Lyman M type expander and took it down half a thousandth with a drill and some abrasive. !58 plated stay put even loaded to 1100-ish fps in 357, even in a 4" model 66.

I use the same approach in auto pistols. Various headstamps in 9mm and 45 vary in thickness and elasticity, enough to make sorting worthwhile. 40 and 10mm are two that you really can't risk setback. These two are often subjects for Kaboom threads and I believe setback is often the unsuspected culprit.

That the companies who design, manufacture, warranty and market plated bullets don't recommend roll crimping is telling.
Reply With Quote
The Following User Likes This Post:
  #10  
Old 04-04-2017, 08:02 PM
Inyo Boy's Avatar
Inyo Boy Inyo Boy is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Mar 2017
Location: Western PA
Posts: 5
Likes: 1
Liked 1 Time in 1 Post
Default

According to Berry's:

"You can use both the Taper and Roll Crimp on Berry's Bullets.

We recommend a light crimp on the bullet, just enough to put pressure against the bullet without denting or deforming the plating. If you were to pull the bullet out of a case with the proper crimp you would find no more than a scratch on the surface of the plating. If you are denting or deforming the bullet, your accuracy will suffer and the bullet may start to tumble before it hits the target."

I use Berry's 158 gr flat points for 38 and mid 357. I set my roll crimp so that it just kisses the case. Works for me.
Reply With Quote
The Following User Likes This Post:
  #11  
Old 04-04-2017, 08:27 PM
Just another 22 shooter's Avatar
Just another 22 shooter Just another 22 shooter is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Sep 2010
Location: midwest
Posts: 1,760
Likes: 4,703
Liked 2,708 Times in 908 Posts
Default

I pull the seating stem out of a 9mm seating/taper crimp die and use it for a taper crimp on my 357 magnum plated bullet loads.
Reply With Quote
The Following User Likes This Post:
  #12  
Old 04-04-2017, 08:39 PM
WR Moore WR Moore is offline
Member
 
Join Date: Oct 2006
Posts: 6,581
Likes: 1,788
Liked 5,342 Times in 2,685 Posts
Default

To answer fredj338's question, the bullets are 0.452 after plating. Give or take a couple ten thousandths.

However, given the warning about possible separation of the plating (kinda doubtful, it's bonded to the core, plus the pressure is behind it) warning about possible accuracy degradation will probably get more attention that anything else.

I haven't noted any accuracy issues with either 9mm or .45 bullets crimped tighter than the alleged Berry note above. Possibly I'm not fussy enough. The pressure on the bullet as it passes through the bore will most likely iron out any minor imperfections.

As a matter of fact, many factory loads without cannelured bullets are factory crimped. Sometimes quite heavily. I once pulled factory .222 loads for the bullets and the crimp was visible with the naked eye. They still shot in one ragged hole.
Reply With Quote
  #13  
Old 04-04-2017, 09:08 PM
Thomasino Thomasino is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Mar 2017
Posts: 88
Likes: 13
Liked 70 Times in 35 Posts
Default

I just loaded 50 rounds of 38 Special using Berry plated bullets 148 grain double ended wad-cutters. I give them a firm roll crimp and never have a problem. I have pulled some of these bullets after I gave them a firm crimp and there was the expected indentation but no damage was done to the bullet as far as going through the plating. They're pretty tough bullets and seem to handle a cramp very well.

Sent from my Moto G (4) using Tapatalk
Reply With Quote
  #14  
Old 04-04-2017, 09:16 PM
SLT223's Avatar
SLT223 SLT223 is offline
Member
Crimping Plated Bullets?  
Join Date: Jan 2009
Posts: 3,304
Likes: 2,719
Liked 5,046 Times in 1,439 Posts
Default

I use Xtreme plated. They are thick enough to take a roll crimp. I would guess competing products are the same. Test it out on you press and pull it down. See how it looks.
Reply With Quote
  #15  
Old 04-04-2017, 09:44 PM
BC38's Avatar
BC38 BC38 is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Nov 2013
Location: Spokane, WA
Posts: 13,481
Likes: 1,155
Liked 18,412 Times in 7,285 Posts
Default

FWIW, last year I bought a batch of 1000 158gr RNFP plated bullets that were from "de-milled" (a.k.a. disassembled) factory ammo. While I can't say for sure, I suspect they were Xtreme plated bullets that came from breaking down Freedom Munitions reloads (since they are Xtreme's sister company and load with their components). They looked just like the ones I have bought from Xtreme.

Anywho, the bullets all had a very visible indented ring around them where they had been roll crimped. Kinda like the crimp formed its own shallow cannelure.

The entire rest of the bearing surface of the bullets looked untouched, and they measured out at .357, for the entire bearing surface - all except for the crimp ring.

They shot just fine and I didn't see any accuracy issues, but maybe I'm just not a good enough shot to notice

So, when I load plated bullets, I do a medium roll crimp - just like the makers of the bullets do when they load their own remanufactured ammo for sale.
Reply With Quote
  #16  
Old 04-04-2017, 10:15 PM
bigedp51 bigedp51 is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Jul 2011
Posts: 409
Likes: 6
Liked 399 Times in 195 Posts
Default

The diameter of the expander governs bullet grip be it a handgun or rifle. And with plated bullets all that is needed is a taper crimp to close up the case mouth .001 more than case diameter.

With a plated bullet your not shooting magnum loads and proper bullet grip with a slight taper crimp should be good enough. I put a very light taper crimp on my .44 magnum practice loads with plated bullets and do not have a problem.

I know its a rifle type "M" die below but look at the expanders diameters for a .224 bullet. Your bullet grip below is .003 smaller than bullet diameter and the .226 diameter is to start the bullet straight in the case. And all that is needed is a slight taper crimp to streamline the case mouth.



Your crimp is governed by how hot the load and keeping recoil inertia from allowing the bullet to move. My target loads in my AR15 A2 HBAR are not crimped because my expander is .002 smaller than bullet diameter.
Reply With Quote
  #17  
Old 04-04-2017, 10:56 PM
gman51 gman51 is offline
Member
Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets? Crimping Plated Bullets?  
Join Date: Feb 2012
Location: Just West of Houston
Posts: 3,468
Likes: 787
Liked 4,674 Times in 2,062 Posts
Default

I had loaded Ranier 38 caliber plated round nose bullets with 2.5 gr clays powder. I didn't crimp them because Ranier said not to because it could cut the plating. I had 3 squibs, one bullet found 10' from where I was shooting and several laying on the ground at the target 10 yrds. away.
I took the last squib to a gunsmith for him to advise me what was what. he said the Clays is slow burning and causing the problems. I had my doubts about his advice and called Hodgdon and surprisingly was on the line with customer tech.
We talked for awhile and he asked what powder and bullets I was using. He also said the gunsmith doesn't know squat about Hodgdon Clays because it is one of the fastest powders on the market.
The man was very nice explaining things to me being a novice to reloading. I told him I really didn't think I missed putting powder in that many if any. He said rather than dumping powder from all the remaining couple hundred rounds to try putting a crimp on some first. He believed because of no crimp the bullets were moving out from initial ignition losing any seal for remaining powder and making the shell space larger. Both causing the round not to build pressure and causing the squibs and short distance falls.
I bought a Lee crimp die and crimped several rounds. I noticed a big difference in sound report and recoil. The bullets were actually hitting the target with decent pattern. So I crimped all the remaining rounds and they all shot very well with no squibs or weak rounds.
I now use Swamp Popper coated cast bullets and upped the Clays powder to 3.5 gr. I do crimp in final step. The rounds perform very well.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Crimping LRN 9mm bullets... bflobill69 Reloading 26 12-21-2019 05:44 PM
Final Re-Sizing/Crimping Operation Loosenes Plated Bullets? Speedo2 Reloading 25 12-13-2015 01:14 AM
Question about crimping bullets after seating ricks69z28 Reloading 9 01-09-2013 11:42 AM
Crimping Plated Bullets coat Reloading 5 09-02-2012 03:24 PM
Crimping cast bullets Fauquier Reloading 6 05-22-2011 07:49 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 04:11 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)