Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 04-13-2017, 08:13 AM
BZimm BZimm is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Nov 2016
Location: Michigan; 86W, 46N
Posts: 48
Likes: 103
Liked 28 Times in 16 Posts
Default RCBS Die Question 2

Now that we've got the whole cardboard wafer thing worked out, I have another RCBS question. I appreciate you guys helping me out; I enjoy the technical aspect of this hobby a lot.

Ok, this is about an RCBS 3 die set for 38/357.

1) On the sizing die I've noticed that the decapping pin keeps loosening up. When I snug the pin up with the jam nut, the pin appears slightly off-center. Then during use it loosens up again but centers itself at the die opening. It is bent, right? Operationally it seems ok and knocks the primers out just fine, but to me it seems that I should get a new pin?

2) The set came with a spacer that enables switching from 38 to 357 and I understand that part. When new, this die set would have come with three of these spacers right? One for each die?

The great price I paid for this set ain't lookin' quite so great right now. Even if it did include a free cardboard wafer....

BZimm
__________________
I'm accountable for my actions

Last edited by BZimm; 04-13-2017 at 08:14 AM. Reason: Too many words
Reply With Quote
  #2  
Old 04-13-2017, 08:18 AM
OKFC05 OKFC05 is offline
Member
RCBS Die Question 2 RCBS Die Question 2  
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,158
Likes: 3,604
Liked 5,199 Times in 2,172 Posts
Default

Why would you need a spacer for the sizing die?
Hint: You don't, you size to the bottom of the case, which is in the same place in the shell holder with both calibers.


The bell and seat/crimp dies work on the mouth of the case and need to go up 1/8" for .357.
__________________
Science plus Art

Last edited by OKFC05; 04-13-2017 at 08:24 AM.
Reply With Quote
The Following 5 Users Like Post:
  #3  
Old 04-13-2017, 08:32 AM
Fishinfool's Avatar
Fishinfool Fishinfool is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Feb 2011
Location: Central PA
Posts: 4,550
Likes: 8,201
Liked 11,436 Times in 3,018 Posts
Default

Make sure the decapper pin is straight in the die when you tighten it up. You could remove the pin, and lay it flat on a table to see if it is bent. If so, a few light taps with a small hammer should straighten it. It pays to have a couple spares, as they do break. If the retaining set screw / nut keeps loosening up, a drop of Locktite blue might help.

Larry

Last edited by Fishinfool; 04-13-2017 at 08:34 AM.
Reply With Quote
The Following User Likes This Post:
  #4  
Old 04-13-2017, 08:44 AM
arjay's Avatar
arjay arjay is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Mar 2006
Location: Colorado
Posts: 15,082
Likes: 91,551
Liked 26,243 Times in 8,376 Posts
Default

Use a screwdriver and a wrench to tighten the pin and it should hold.A pkg of spare pins will prevent one from ever breaking RCBS Die Question 2
Reply With Quote
The Following 4 Users Like Post:
  #5  
Old 04-13-2017, 08:45 AM
4barrel's Avatar
4barrel 4barrel is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Jan 2012
Location: OVER the hill in TEJAS
Posts: 2,725
Likes: 13,107
Liked 4,339 Times in 1,773 Posts
Default

Make sure the pin size is correct. Adjust to barely punch out the primer & then another 1 1/2 round.
Reply With Quote
The Following 2 Users Like Post:
  #6  
Old 04-13-2017, 08:50 AM
Bayou52 Bayou52 is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Feb 2017
Location: SE Louisiana
Posts: 295
Likes: 864
Liked 788 Times in 176 Posts
Default

RCBS customer service is top notch. Feel free to call them with any remaining unanswered questions....They are more than helpful!

Bayou52
__________________
Bayou52
NRA Life Member
Reply With Quote
The Following 2 Users Like Post:
  #7  
Old 04-13-2017, 09:15 AM
Collo Rosso's Avatar
Collo Rosso Collo Rosso is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Jan 2014
Location: Upstate South Carolina
Posts: 1,523
Likes: 1,267
Liked 2,021 Times in 760 Posts
Default

Order a pack of the proper pins and toss the bent one you have. I double nut the threaded shaft and use a small set of pliers to tighten the cap. Use the same double nut to get the cap off. You could try locktite but I'd hate to see you not be able to get the cap off the next time you snap a pin. My 38/357 die set is Lyman, all others RCBS. I prefer RCBS.
Starting out on an old single stage I got really fast setting up dies. My 38/357 set had no spacer so when I swapped calibers I just readjusted the dies. You don't have to touch the first die. If I had the spacer I probably wouldn't use it.
Reply With Quote
The Following 2 Users Like Post:
  #8  
Old 04-13-2017, 09:21 AM
phonejack phonejack is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Mar 2014
Location: Arkansas
Posts: 204
Likes: 64
Liked 230 Times in 106 Posts
Default

To center the decapping pin, decap a case. With the pin still inside the flash hole , loosen and then retighten. This will center the decapping pin.
Reply With Quote
The Following 3 Users Like Post:
  #9  
Old 04-13-2017, 10:30 AM
Hasbeen1945 Hasbeen1945 is offline
Absent Comrade
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Mar 2015
Location: Deer Park Texas
Posts: 450
Likes: 410
Liked 596 Times in 212 Posts
Default

I probably would not use locktite. You will need to take the die apart once in a while to clean it. Double nut is the answer.
Reply With Quote
The Following User Likes This Post:
  #10  
Old 04-13-2017, 11:12 AM
Skeet 028 Skeet 028 is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Feb 2010
Location: Wyoming
Posts: 6,137
Likes: 6,330
Liked 7,047 Times in 2,984 Posts
Default

I think he means the whole decapping rod become loose and off center. Center it nd if possible double nut it when straight like phonejack said. The dies only come with one spacer which as pointed out you don't need on the sizer. Call RCBS customer service. Bet they'll send you another spacer if you need it. Reason they only send one is cause most people load with a single stage press anyway.
Reply With Quote
The Following User Likes This Post:
  #11  
Old 04-13-2017, 12:44 PM
MichiganScott MichiganScott is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Jan 2012
Location: God's Country
Posts: 4,711
Likes: 1,235
Liked 3,535 Times in 1,770 Posts
Default

You only need the spacer for the crimp die. The bullet seater die can be adjusted, and once the sizing die is set it will work for both cases.

My feelings are that if you can deprime without incident, the pin is probably not bent.
Reply With Quote
The Following 2 Users Like Post:
  #12  
Old 04-13-2017, 01:22 PM
gwpercle's Avatar
gwpercle gwpercle is online now
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Nov 2011
Location: Baton Rouge, La.
Posts: 6,838
Likes: 7,390
Liked 8,045 Times in 3,651 Posts
Default

Two ways to center the decapping pin.

1. Just eyeball it . Center the pin in the die opening.

2. Decap a case, with slightly loose nut, keeping the pin in the case primer flash hole, make sure the case is centered in the shell holder (not off to one size) Then tighten the nut , with a little wrench , while the pin is still in the flash hole.

Remember ...not every and all flash holes will be dead center but most will be close, a little wiggle room in the shell holder will allow the case to self-center.

Tighten the nut with a wrench , I wouldn't use lock tight.
Buy a package of pins, a bent one is a pain and once bent they seem to never be as good as new. Straighten them untill you get a new one.

The spacer is for the crimping and seating die . Sizing die is OK all the way in. Adjust flairing stem as needed or buy a spacer if you like.
Hint , with revolver loads and roll crimps , seat bullet first and crimp in two separate steps . Ammo will be better and life easier.

Gary
Reply With Quote
The Following User Likes This Post:
  #13  
Old 04-13-2017, 02:05 PM
lebomm lebomm is offline
Member
RCBS Die Question 2 RCBS Die Question 2  
Join Date: Dec 2008
Location: Seattle
Posts: 1,948
Likes: 38
Liked 821 Times in 490 Posts
Default

I'm not sure I understand the mechanical necessity to double-nut the decapping rod. Since the rod is threaded into the die body, the single nut acts as a jam nut. Replacing the factory knurled round nut with an ordinary hex nut will provide all the security the rod needs.

Larry
Reply With Quote
The Following User Likes This Post:
  #14  
Old 04-14-2017, 01:35 AM
BZimm BZimm is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Nov 2016
Location: Michigan; 86W, 46N
Posts: 48
Likes: 103
Liked 28 Times in 16 Posts
Default

Ok, I understand how to proceed with the sizing die and pin. And I'll get a pack of spares coming. I'll adjust the dies for 357 because I just got my order of new brass and 158gr bullets from Xtreme. I was set up for 38spl because I had some range brass and 105gr cast bullets on the shelf at the time. I have a Lee FCD in the turret so I'll be seating and crimping in two steps. I feel that is a better way to go.

Thank you kindly for all the help. You are a friendly bunch.

BZimm
__________________
I'm accountable for my actions
Reply With Quote
The Following User Likes This Post:
  #15  
Old 04-14-2017, 09:06 AM
Collo Rosso's Avatar
Collo Rosso Collo Rosso is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Jan 2014
Location: Upstate South Carolina
Posts: 1,523
Likes: 1,267
Liked 2,021 Times in 760 Posts
Default

Quote:
Originally Posted by lebomm View Post
I'm not sure I understand the mechanical necessity to double-nut the decapping rod. Since the rod is threaded into the die body, the single nut acts as a jam nut. Replacing the factory knurled round nut with an ordinary hex nut will provide all the security the rod needs.

Larry
The decapping rod for my Lyman die set has no screwdriver slot at the top. I use double nuts (jam nuts) to hold the rod and break loose the pin holder. Should of explained better.
Reply With Quote
  #16  
Old 04-15-2017, 01:00 AM
hdwhit hdwhit is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Sep 2016
Location: North Texas
Posts: 804
Likes: 86
Liked 482 Times in 300 Posts
Default

I own and use RCBS dies almost exclusively, but many years ago I got tired of losing decapping pins and decapping rods to berdan cases or cases with off-center flash holes. I decided to make decapping a separate step in my reloading and bought a Lee Decapping die. I took the decapping assemblies out of my RCBS dies and that really simplified the process and eliminated broken or bent pins and rods.
Reply With Quote
  #17  
Old 04-15-2017, 01:16 AM
Goblin Goblin is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: May 2014
Location: North Texas
Posts: 1,596
Likes: 2,455
Liked 1,148 Times in 608 Posts
Default

The die set only comes with one spacer, but you can buy extras at a reasonable price. As stated by others, you don't need one for the sizer, and I also recommend buying a second crimping die to seat and crimp in two steps.
Reply With Quote
  #18  
Old 04-15-2017, 12:47 PM
Hasbeen1945 Hasbeen1945 is offline
Absent Comrade
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Mar 2015
Location: Deer Park Texas
Posts: 450
Likes: 410
Liked 596 Times in 212 Posts
Default

I also use the Lee universal decaping die. Don't want to size dirty cases. So decap, drop in thumbler, cleans case and primer pocket before I resize.
Grit is the enemy of a sizing die.
Reply With Quote
  #19  
Old 04-15-2017, 02:28 PM
Skeet 028 Skeet 028 is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Feb 2010
Location: Wyoming
Posts: 6,137
Likes: 6,330
Liked 7,047 Times in 2,984 Posts
Default

I double nut the darn decapper on some of my dies because it just won't stay tight for some reason. I also use a decapping die for certain calibers(223 45 auto and 38s) as it is mostly range brass..meaning dirty..Have 3 set up on different old Herter's presses 2 in the garage and one down in the loading room in the basement. Those ol presses aren't worth much so I don't worry about dirt and such. Then I clean the cases inspect and load. Is there any differences tween different decapping dies? I have a couple Dillons and a Lee and Sinclair. I guess the big difference is the cost, huh? The 2 Dillon's were given to me. The Sinclair I have never used. Got it a a gun show for 15 bucks...new
Reply With Quote
  #20  
Old 04-15-2017, 02:52 PM
Ivan the Butcher Ivan the Butcher is online now
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Jan 2008
Location: Harlem, Ohio
Posts: 14,354
Likes: 23,195
Liked 26,154 Times in 9,068 Posts
Default

Once you have accumulated several die sets (of the same brand or mixed) you will find that there are many interchangeable parts. The threads are all ISE standard (and usually fine pitch). Adapter nuts and decapping pins are in just a few diameters. So, you can "Borrow" parts from on die set to see if you have bent or off center parts.

RCBS and Bonanza used to have vender's repair kits. I picked up a number of these as gun shops went out of business. Those really helped with mixing and matching parts!

Having spare decapping pins is a must. Some brands have more than one size (RCBS, older Bonanza, & Redding) some of them are "T" shaped (Dillon, and older Lyman). NOTE if you ever load PPC or BR cartridges, they use extra small flash holes to contain high pressures. Using regular small pins will enlarge the flash hole and make the cases not as consistent as the cases with the extra small holes. (I did this to 55 of my 22 BR cases by decapping in a universal decapping die! They no longer are as accurate!)

Ivan
Reply With Quote
  #21  
Old 04-15-2017, 11:29 PM
BZimm BZimm is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Nov 2016
Location: Michigan; 86W, 46N
Posts: 48
Likes: 103
Liked 28 Times in 16 Posts
Default

I feel a sense of freedom reading through these responses. I am allowed to tinker with this stuff.....once I understand the functional intent. The magic and voodoo of these die sets is slowly fading away. Science is taking over. I love it.

BZimm
__________________
I'm accountable for my actions
Reply With Quote
The Following User Likes This Post:
  #22  
Old 04-19-2017, 09:46 PM
Engineer1911's Avatar
Engineer1911 Engineer1911 is online now
US Veteran
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Aug 2007
Location: Augusta, GA
Posts: 6,113
Likes: 6,644
Liked 6,156 Times in 2,666 Posts
Default

Quote:
Originally Posted by BZimm View Post
I feel a sense of freedom reading through these responses. I am allowed to tinker with this stuff.....once I understand the functional intent. The magic and voodoo of these die sets is slowly fading away. Science is taking over. I love it.

BZimm
NOW YOU REALLY ARE IN TROUBLE ! ! ! Next you'll start talking about saving money.
__________________
S&WHF 366
Reply With Quote
The Following User Likes This Post:
  #23  
Old 04-19-2017, 11:21 PM
Skeet 028 Skeet 028 is offline
Member
RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2 RCBS Die Question 2  
Join Date: Feb 2010
Location: Wyoming
Posts: 6,137
Likes: 6,330
Liked 7,047 Times in 2,984 Posts
Default

[QUOTE=Engineer1911;139562017]NOW YOU REALLY ARE IN TROUBLE ! ! ! Next you'll start talking about saving money.
[/QUOTE

Now I gotta say...I save money on every round I load...If I could only stop shootin so many I'd be golden
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
RCBS Die Question BZimm Reloading 24 04-11-2017 08:13 AM
Old RCBS die question Jeff423 Reloading 11 01-20-2011 12:44 PM
RCBS question hornady Reloading 5 10-04-2010 03:48 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 09:58 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)