|
|
06-23-2017, 04:29 PM
|
|
Member
|
|
|
Join Date: Oct 2015
Location: Southern NJ
Posts: 4,684
Likes: 19,020
Liked 4,190 Times in 1,865 Posts
|
|
Non-carbide dies and progressive presses?
Does anyone have any experience using traditional steel dies to reload cartridges on a progressive press?
I am looking to pick up some inexpensive dies for reloading some practice 380s. Every other set of pistol dies I have are carbide, and I am not looking to stray, but until the finances get stronger, I am considering steel dies.
Opinions, please?
__________________
Judge control not gun control!
|
06-23-2017, 04:32 PM
|
|
Member
|
|
|
Join Date: Aug 2011
Location: Texas
Posts: 498
Likes: 515
Liked 517 Times in 219 Posts
|
|
If carbide dies are available, get them.
Steel is just not worth the hassle.
|
The Following 5 Users Like Post:
|
|
06-23-2017, 04:46 PM
|
Member
|
|
|
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,161
Likes: 3,620
Liked 5,209 Times in 2,174 Posts
|
|
Steel dies on a progressive press is penny wise and pound foolish. A set of Lee .380 carbide dies is not that expensive if your press takes standard dies.
And if you have a Dillon SDB with proprietary dies, buy Dillon dies and smile forever.
__________________
Science plus Art
Last edited by OKFC05; 06-23-2017 at 04:49 PM.
|
The Following User Likes This Post:
|
|
06-23-2017, 06:13 PM
|
|
Member
|
|
|
Join Date: Feb 2006
Location: Kalif. usa
Posts: 6,836
Likes: 2,665
Liked 3,927 Times in 2,366 Posts
|
|
I use steel dies for 223 on my 550. Use OneShot, you don't need to remove the lube. A 380 has a small surface area, would work fine this way. I agree though, Lee carbide dies, about the cost of two boxes of factory 380???
__________________
NRA Cert. Inst. IDPA CSO
Last edited by fredj338; 06-23-2017 at 06:14 PM.
|
The Following User Likes This Post:
|
|
06-23-2017, 07:11 PM
|
Member
|
|
|
Join Date: Jan 2008
Location: Harlem, Ohio
Posts: 14,436
Likes: 23,452
Liked 26,336 Times in 9,128 Posts
|
|
In 1984 I loaded a batch of 223's using RCBS Small Base dies. For lube I used Break Free (in the aerosol). It won't foul primers. If I did it today I would use One Shot or a similar product. The 4 week project turned out 20,000 rounds! I never loaded 55grain FMJ ammo again and still have about 6500. Shoots less than 1/2" @ 100 yards in my older AR and less than 1/4" in the Cooper 21 bolt gun. Absolutely shot terrible in my stainless Mini-14: turns out the Mini was junk (I tried 5 of them, blue and stainless. Blue would do 3" at 100 and stainless would do 5"). Use a good load! Use the same components in the whole batch (One lot of primers, one lot of powder etc.)
Use a good brand of steel dies! The quality of the dies is more important than weather steel or carbide!
Ivan
|
06-23-2017, 11:10 PM
|
Member
|
|
|
Join Date: Mar 2006
Location: NE PA
Posts: 264
Likes: 75
Liked 150 Times in 95 Posts
|
|
Are here any non-carbide steel .380 dies available anymore?
|
06-23-2017, 11:24 PM
|
|
US Veteran
|
|
|
Join Date: Dec 2005
Location: Birmingham, Alabama
Posts: 4,483
Likes: 228
Liked 2,398 Times in 1,082 Posts
|
|
Bad idea. Get Lee carbide and don't look back.
|
|
Posting Rules
|
|
|
|
|