|
|
04-05-2018, 06:14 PM
|
Member
|
|
|
Join Date: Feb 2017
Location: southern illinois
Posts: 1,944
Likes: 2,249
Liked 2,389 Times in 1,008 Posts
|
|
158 gr. coated lswc for .38 spl. loads
I'm new to this,just getting started reloading. thanks for reading. I'm thinking about using some mo. bullet co. 158gr coated semi wad cutters over 3.5-4.0 red dot and a fed 100 primer to kill steel plates and bowling pins. anyone see any red flags here? are coated bullets worth the money?
|
04-05-2018, 06:29 PM
|
Member
|
|
|
Join Date: Jan 2011
Location: Crawford County PA
Posts: 3,704
Likes: 4,369
Liked 6,710 Times in 2,418 Posts
|
|
I use 3.1 of Bullseye with Bayou coated bullets and like them. Less smoke than with lead and ok accuracy. A little light in my opinion for bowling pins off a table though.
__________________
Made it, Ma! Top of the world!
|
04-05-2018, 06:48 PM
|
|
Member
|
|
|
Join Date: Apr 2017
Posts: 1,624
Likes: 2,003
Liked 1,653 Times in 809 Posts
|
|
I use powder coated, Hi Tek coated, and VHT coated bullets. ALL leave no leading, none, nada, and leave the bore shinning like it was just polished. I also get slightly higher velocity from any of the above over using lubed cast bullets. I rarely use lubed bullets anymore, except for bullets in loops on the belt, I don't want to look like sissy with lipstick bullets.
|
The Following User Likes This Post:
|
|
04-05-2018, 08:02 PM
|
Member
|
|
|
Join Date: Dec 2016
Location: South Carolina
Posts: 1,705
Likes: 1,049
Liked 3,510 Times in 957 Posts
|
|
I think coated areca bargain. Clean shooting and accurate. Also can push them very hard if you desire without leading problems.
|
04-05-2018, 08:06 PM
|
Member
|
|
|
Join Date: Dec 2011
Location: South Oregon Coast
Posts: 1,820
Likes: 89
Liked 1,648 Times in 584 Posts
|
|
I have shot a ton of SNS coated bullets and agree with what's been said already. Very little smoke and very clean to handle. And you never have to worry about getting a batch of bullets where half the lube has fallen out. My favorite load is a 158gr LSWC over 4.9 grains of titegroup. Pretty close to a maximum load but still very low pressure in a .357. Accurate in everything I own from 1 7/8" barrel up to an 8 3/8" barrel and not a lot of recoil. And speaking of lipstick bullets, I don't know why everyone seems to be going to a red coating. SNS used to be gold but they're red too now.
Last edited by 1sailor; 04-05-2018 at 08:09 PM.
|
04-06-2018, 11:22 AM
|
|
Moderator SWCA Member Absent Comrade
|
|
|
Join Date: Dec 2006
Location: Northeast PA, USA
Posts: 8,877
Likes: 1,029
Liked 5,070 Times in 2,660 Posts
|
|
According to Alliant the max charge of Red Dot with that bullet should be 3.4gr for standard pressure and 3.8gr for +P pressures. If you go to 4.0 gr you will be above published limits. If you're looking for more velocity/energy for knocking down pins you will probably do better with a slower powder.
__________________
Freedom is never free!!
SWCA #3437
|
04-06-2018, 09:32 PM
|
Member
|
|
|
Join Date: May 2016
Location: 30min SE Montreal
Posts: 2,026
Likes: 150
Liked 1,540 Times in 841 Posts
|
|
Like ArchAngel said;you are very much in +P territory for .38Spl(do you shoot them in a .38 or in a .357?).
I too work with a slower burning powder when I get into the heavyweights(for the .38Spl).Easier and safer to work with.
|
04-07-2018, 11:39 AM
|
Absent Comrade
|
|
|
Join Date: Mar 2015
Location: Deer Park Texas
Posts: 450
Likes: 410
Liked 596 Times in 212 Posts
|
|
I am liking Accurate #5 with my coated 158 LSWC bullets.
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
|
|
|
|
All times are GMT -4. The time now is 10:50 AM.