Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 02-05-2020, 11:28 AM
mmb617's Avatar
mmb617 mmb617 is offline
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Oct 2019
Location: Altoona, PA
Posts: 851
Likes: 231
Liked 1,730 Times in 521 Posts
Default At what point in the process do you anneal?

I like to anneal my .223 cases before each reloading and I use the very low tech hold the neck in a propane torch flame till the bottom gets too hot to hold with bare fingers then drop them into a pan of water method. I'm trying to decide exactly which step in the reloading process would be best for this.

What I've been doing is annealing them right after tumbling but it's hard to be sure all the water is completely out of them later if I'm charging them the same day and I worry about damp powder.

Because the spent primer is still in the cases the water doesn't simply run out, the case has to be shaken a bit to get it out. I've drilled holes through the bottom of a couple case blocks and I stand the cases upside down in them but they still don't drain completely. When I then size/decap, which I do as one step, some water usually comes out at that point, so there's still some dampness.

If I size/decap before I anneal having an opening in each end of the case should help the water drain but would the residual lube in the case mouth interfere with proper heat transfer?

Maybe the best bet would be to get a separate decapping die and do that before annealing then size them afterwards?

So I'm curious about how others do it. I know some of you have equipment that doesn't require water but I can't be the only one using a cheap low tech method can I?

I'm still pretty new at this so I'd appreciate your thoughts.
Reply With Quote
  #2  
Old 02-05-2020, 12:16 PM
Warren Sear's Avatar
Warren Sear Warren Sear is online now
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Apr 2011
Location: Twin Cites, Minnesota
Posts: 5,141
Likes: 10,957
Liked 10,857 Times in 3,275 Posts
Default

I pretty much never anneal.
Reply With Quote
The Following 7 Users Like Post:
  #3  
Old 02-05-2020, 12:30 PM
DWalt's Avatar
DWalt DWalt is online now
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,479
Likes: 236
Liked 28,940 Times in 14,012 Posts
Default

During case manufacture, case neck annealing is done by passing the case neck/shoulders under burning gas jets. I have seen that done at all the big factories (Rem, Win, Federal, Lake City). They are not cooled with water afterward, just cool naturally. Therefore I assume it is not necessary to do anything else. I usually anneal only if I am forming cases, i.e., changing from one size to another (making 8x57 cases from .30-'06, etc.). After forming I just use a propane torch on the necks, no water dip.

I know some anneal case necks by dipping the necks in molten lead. I guess that would work also, but I have never done it.

Last edited by DWalt; 02-05-2020 at 12:36 PM.
Reply With Quote
The Following User Likes This Post:
  #4  
Old 02-05-2020, 12:49 PM
elpac3's Avatar
elpac3 elpac3 is offline
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Apr 2012
Location: Mpls, Minnesota
Posts: 867
Likes: 87
Liked 967 Times in 398 Posts
Default

For my rifle cases I use a universal decap die so I don't scratch my "good" size/decap die. After wet tumbling I put the cases on a cookie sheet (when the wife is not home) and bake them at 175 for an hour to dry them out.

For a more precise method of annealing, consider Templac to see just how long you need to hold the case in the flame.
Reply With Quote
  #5  
Old 02-05-2020, 01:38 PM
ken158 ken158 is offline
Member
At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Nov 2005
Location: VA
Posts: 4,667
Likes: 1,436
Liked 4,487 Times in 1,927 Posts
Default

Anneal after resizing for another caliber and after about every 3 or 4 firings. A water dump is not necessary and only adds time and effort getting the water out and drying. Templac will let you know how long to keep neck in the flame. After figuring out the timing, you don’t need it anymore. I count to 5 and drop case in a pan. Not sure I would want to cook dinner in an oven that had previously dried brass with the residue inside as well as primers.
__________________
S&W factory revolver armorer

Last edited by ken158; 02-06-2020 at 12:11 PM.
Reply With Quote
The Following User Likes This Post:
  #6  
Old 02-05-2020, 01:50 PM
andy52's Avatar
andy52 andy52 is offline
US Veteran
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Feb 2017
Location: Missouri
Posts: 2,929
Likes: 3,902
Liked 6,802 Times in 1,851 Posts
Default

I only anneal brass for my precision bolt action rifles and then only after about 3-5 reloads. If your using a semi-auto for your .223 it's just not worth the trouble consider how inexpensive .223 brass is. At a buck apiece for my Lapua then it's worth it.

Last edited by andy52; 02-05-2020 at 06:24 PM.
Reply With Quote
The Following 2 Users Like Post:
  #7  
Old 02-05-2020, 01:53 PM
robertrwalsh robertrwalsh is offline
SWCA Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: May 2008
Location: Peoples Republic of Calif
Posts: 4,642
Likes: 1,226
Liked 5,984 Times in 2,132 Posts
Default

I never anneal. Too much trouble. If it neck splits, throw it away.
Reply With Quote
  #8  
Old 02-05-2020, 02:27 PM
AManWearingAHat's Avatar
AManWearingAHat AManWearingAHat is offline
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: May 2018
Location: WI
Posts: 507
Likes: 212
Liked 804 Times in 287 Posts
Default

Annealing after every loading is unnecessary unless you're really chasing the smallest groups possible or shooting F Class or something.

That said, I am a metallurgist and I would recommend annealing post sizing as that will remove any work hardening and internal stress that is imparted on the brass by the sizing operation.
Reply With Quote
The Following 2 Users Like Post:
  #9  
Old 02-05-2020, 03:44 PM
DWalt's Avatar
DWalt DWalt is online now
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,479
Likes: 236
Liked 28,940 Times in 14,012 Posts
Default

Yes, if one is going to anneal the necks, then it should be done after resizing. Sizing causes work hardening, and annealing simply re-softens (stress relieves) the brass so it is not so brittle and apt to crack on firing. At one time many years ago, annealing was not performed during brass case manufacture, and after aging for several years, split cases would often result from the first firing.
Reply With Quote
  #10  
Old 02-05-2020, 03:50 PM
Lou_the_welder's Avatar
Lou_the_welder Lou_the_welder is offline
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Aug 2015
Location: Los Angeles,California
Posts: 1,885
Likes: 3,791
Liked 4,094 Times in 1,212 Posts
Default

I throw the cases away after they "need" to be annealed.
Reply With Quote
  #11  
Old 02-05-2020, 06:32 PM
andy52's Avatar
andy52 andy52 is offline
US Veteran
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Feb 2017
Location: Missouri
Posts: 2,929
Likes: 3,902
Liked 6,802 Times in 1,851 Posts
Default

Quote:
Originally Posted by AManWearingAHat View Post
Annealing after every loading is unnecessary unless you're really chasing the smallest groups possible or shooting F Class or something.

That said, I am a metallurgist and I would recommend annealing post sizing as that will remove any work hardening and internal stress that is imparted on the brass by the sizing operation.
Couldn't have said it better, I am a F class shooter and even that doesn't require annealing after ever reload.
Most F class shooter fire form and neck size the case which only minimally stretches the case.
I'm never happy with my loads unless all bullets holes are touching at 100 meters. At that point you can work on out with at least a good degree of confidence.
Reply With Quote
The Following User Likes This Post:
  #12  
Old 02-06-2020, 02:28 AM
Twoboxer's Avatar
Twoboxer Twoboxer is offline
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Mar 2012
Location: Eastern Pennsylvania
Posts: 1,033
Likes: 340
Liked 736 Times in 398 Posts
Default

The folks who have done the most scientific work on annealing brass cases are Annealing Made Perfect (AMP). There should be no bias in their recommendation because when you anneal does not affect their potential sales. Their recommendation?

"Annealing should always be done before resizing. This eliminates spring back, and ensures repeatable and accurate shoulder bumping and neck sizing."

Annealing isn't just about case life. If your goal is consistent neck tension, it's pretty simple to conclude that annealing should be done after each firing.

Is it necessary? That depends on you, your goals, and your results.
Reply With Quote
  #13  
Old 02-06-2020, 02:57 AM
AManWearingAHat's Avatar
AManWearingAHat AManWearingAHat is offline
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: May 2018
Location: WI
Posts: 507
Likes: 212
Liked 804 Times in 287 Posts
Default

Quote:
Originally Posted by Twoboxer View Post
The folks who have done the most scientific work on annealing brass cases are Annealing Made Perfect (AMP). There should be no bias in their recommendation because when you anneal does not affect their potential sales. Their recommendation?

"Annealing should always be done before resizing. This eliminates spring back, and ensures repeatable and accurate shoulder bumping and neck sizing."

Annealing isn't just about case life. If your goal is consistent neck tension, it's pretty simple to conclude that annealing should be done after each firing.

Is it necessary? That depends on you, your goals, and your results.
This is correct if you want to impart the same amount of strain hardening into every case in what I guess would technically be the most repeatable way. I honestly doubt you would see much of a difference on paper, if any, annealing before vs after.
Reply With Quote
The Following User Likes This Post:
  #14  
Old 02-06-2020, 11:13 AM
mmb617's Avatar
mmb617 mmb617 is offline
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Oct 2019
Location: Altoona, PA
Posts: 851
Likes: 231
Liked 1,730 Times in 521 Posts
Default

Thanks guys you've given me much food for thought. The only reason I anneal every time is because I can't adequately keep track of how many firings it's been since last done with the mixture of my own brass and occasional purchased used brass. I want to get maximum use out of my brass since it's a big part of the cost, and I have the time to do the extra step.

Interesting that there are differing opinions on whether it should be done before of after sizing, and what sounds like reasonable arguments for both ways.

I use the water dump because my crude method doesn't insure that I'm not getting the brass too hot and I've read that while the neck area needs to hit 700 degrees, the lower part of the case shouldn't get over 400 degrees. I'm afraid that without the water cooling immediately afterwards the lower part might get too hot as the neck heat migrates down.

I don't have to worry about the wife freaking out as she passed away last year so maybe drying the cases in the oven is a good option.

Just kicking it around in my head I'm thinking that if I anneal after sizing and use the water dump it would probably help remove the lube since I use the Lee water soluble lube. That would also mean the spent primer is removed and the water isn't trapped by only having one opening in the shell. I could then use the oven to insure they are completely dry.

Thanks everybody for their thoughts.
Reply With Quote
  #15  
Old 02-06-2020, 12:00 PM
gwpercle's Avatar
gwpercle gwpercle is offline
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Nov 2011
Location: Baton Rouge, La.
Posts: 6,838
Likes: 7,390
Liked 8,046 Times in 3,652 Posts
Default

I've been reloading for ...a long time and can honestly say I've never annealed a case !

Military surplus 30-06 , 308 , 45 acp and 38 special are so common and cheap I just replace them .
To get maximum case life we were taught how to properly adjust dies and how to neck size cases. You can get a lot of case life with properly set up dies and paying attention to details .
Gary
__________________
Certified Cajun
NRA Member
Reply With Quote
  #16  
Old 02-06-2020, 12:17 PM
H Richard's Avatar
H Richard H Richard is offline
US Veteran
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Aug 2006
Location: West Central IL
Posts: 22,758
Likes: 18,437
Liked 22,313 Times in 8,245 Posts
Default

I have never anneal. I primarily load (rifle) 22-250 or .222. I have enough brass that it may only get loaded every 2nd or 3rd year. Since I neck size after the initial loading, I don't see the value t anneal. As long as my Remington 700 groups within 1/4-1/2" at 100 yards I don't worry about it.
__________________
H Richard
SWCA1967 SWHF244
Reply With Quote
  #17  
Old 02-06-2020, 03:20 PM
grover99 grover99 is online now
US Veteran
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: Apr 2012
Location: Missouri
Posts: 1,240
Likes: 370
Liked 2,760 Times in 681 Posts
Default

The first time I decided to anneal a case I mistakingly picked a case with a live primer. well that was exciting and the last time I did that
Reply With Quote
The Following 2 Users Like Post:
  #18  
Old 02-08-2020, 06:46 PM
Qc Pistolero Qc Pistolero is offline
Member
At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal? At what point in the process do you anneal?  
Join Date: May 2016
Location: 30min SE Montreal
Posts: 2,026
Likes: 150
Liked 1,540 Times in 841 Posts
Default

I size and decap,anneal with the torch and dump the case in a 5gal half filled with water.The dumping in the water is done so as not ding the soft case mouth.When done,I put the cases on a thick cloth cases and let dry for a couple of days.
I haven't seen much difference as far as accuracy is concerned but the cases definitely last longer.
I don't do it for easy to get calibers but for brass that goes expensive,I think it is worth it,more so after putting all the time to trim an deburr
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Fixed Sight Point of Impact vs Point of Aim turnejm S&W Revolvers: 1961 to 1980 12 08-09-2017 09:48 PM
My new single point paracord sling (2 and 3 point available as well) Jyezahn Smith & Wesson M&P 15-22 54 02-11-2013 08:50 PM
Ever anneal brass? Skip Sackett Reloading 14 01-29-2013 10:07 AM
Point of Aim/Point of Impact Speer .38 +P 135 gr. Gold Dot Ammo Walter Rego Ammo 14 09-13-2012 02:18 PM
Model 13 Point of Aim- Point of Impact? texasjarhead S&W Revolvers: 1961 to 1980 1 01-03-2011 03:10 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 11:37 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)