|
|
05-06-2020, 07:46 PM
|
Member
|
|
|
Join Date: Dec 2014
Location: Western MT.
Posts: 1,131
Likes: 5,006
Liked 1,040 Times in 438 Posts
|
|
544 groove diameter??
Recently purchased a model 544 in 44-40. Really want to roll some out and make some noise. I have some O/T laser cast 200 grainers in .430 from my 44 special that I could use, but haven't slugged the bore for a correct diameter. Are the 544's running a standard .429" groove diameter, allowing me to use these, or are they closer to the old .427". The guns were made for one year in 1986. Thanks.
__________________
Todd
|
05-07-2020, 10:51 AM
|
Member
|
|
|
Join Date: Jun 2016
Location: for now ,Texas
Posts: 2,741
Likes: 186
Liked 3,300 Times in 1,525 Posts
|
|
It is my understanding that S&W used barrels for the 44 magnum/ specials on the 544 . I have read that the cylinder throats are .428 and the groove is .429 . I don't own one , just sharing what seems to be common knowledge . It's very easy to crush a case or get the bullet in the case crooked and have a bulge on one side of the case with the larger bullets so take your time . It's not like loading a little larger bullet in a 44 magnum / special case . The case walls on the 44-40 are very thin . Yes, I do reload for it . Regards Paul
Last edited by cowboy4evr; 05-07-2020 at 10:54 AM.
|
The Following 3 Users Like Post:
|
|
05-07-2020, 11:23 AM
|
|
SWCA Member
|
|
|
Join Date: Feb 2005
Location: Cocoa Beach, Florida
Posts: 10,580
Likes: 3,066
Liked 22,560 Times in 5,845 Posts
|
|
Most folks that slugged the bores of Model 544 revolvers came out with .429+/-
That is why it was popular to fit a 44 cylinder to these revolvers back in the day
You can instantly end up with a 5" 44 Special or 44 Magnum
I might be willing to shoot Specials through one, but not the Magnums
As to crushing cases while hand loading, If I were going to load this cartridge, I would swap out the expander plug that was supplied with the 44-40 dies and use one intended for the 44 Magnum
After all the 44-40 was Winchesters 1st metallic cartridge and that was almost 150 years ago. Remember we did not have SAAMI back then. So the 44-40 chamber and barrels had wildly varying dimensions from manufacturer to manufacturer
__________________
"Acta non verba"
|
The Following User Likes This Post:
|
|
05-07-2020, 12:05 PM
|
|
Member
|
|
|
Join Date: May 2012
Location: S. Orygun
Posts: 2,461
Likes: 1,963
Liked 1,827 Times in 987 Posts
|
|
Quote:
Originally Posted by cowboy4evr
It is my understanding that S&W used barrels for the 44 magnum/ specials on the 544 . I have read that the cylinder throats are .428 and the groove is .429 . I don't own one , just sharing what seems to be common knowledge . It's very easy to crush a case or get the bullet in the case crooked and have a bulge on one side of the case with the larger bullets so take your time . It's not like loading a little larger bullet in a 44 magnum / special case . The case walls on the 44-40 are very thin . Yes, I do reload for it . Regards Paul
|
Unless soft bullets are used with upper pressures the .428"/.429" dimensions are a recipe for barrel leading. If I bought a gun in 44/40, I would want one that used "normal" cartridge dimensions; .427" bullet diameter and a .428" groove diameter (SAAMI)...
Last edited by mikld; 05-07-2020 at 12:07 PM.
|
The Following User Likes This Post:
|
|
05-07-2020, 01:24 PM
|
Member
|
|
|
Join Date: Dec 2014
Location: Western MT.
Posts: 1,131
Likes: 5,006
Liked 1,040 Times in 438 Posts
|
|
Thanks for the answers. I plan on single staging these, and not running them thru my Dillon for the fact that they can be finicky to reload. In most all of my reading I've found that you want to use a bullet that is .001/.002" larger than the groove diameter. So with the current SAAMI specs of .4285", a .430" bullet should work fine, at least by my logic. Would changing out the expander ball for a 44 mag for .0005" make that much difference?
__________________
Todd
|
05-07-2020, 03:16 PM
|
Member
|
|
|
Join Date: Jan 2008
Location: Harlem, Ohio
Posts: 14,425
Likes: 23,428
Liked 26,305 Times in 9,120 Posts
|
|
I loaded 3 batches of 44-40 on my Dillon 550b, batch size was 1500. I used Bear Creek moly coated on the first batch and Patriot cast bullets on #2 & #3. All sized to .427 for Ruger Vaquero 4". The adjustment of the seating and crimp die was critical! Case length was a factor in crushed cases! I hate to admit the only way I could get consistent good ammo was to seat and crimp separately and use a Lee FCD, then production was back up to 500 per hour and 100% wrinkle free!
Ivan
BTW Midway puts the Lee Factory Crimp dies on sale a few times a year. One year on a whim, I bought 12 of them in old cartridges, just to have them. I usually don't need or like them, but when you really need one, YOU REALLY NEED ONE.
More modern cases are .015" of neck wall thickness, but 44-40, 38-40, 25-20, 32-20 and 22 Hornet are only .010" Thick. (they learned their lesson and 218 Bee is .015"!)
Last edited by Ivan the Butcher; 05-07-2020 at 03:24 PM.
|
The Following User Likes This Post:
|
|
05-07-2020, 09:34 PM
|
Member
|
|
|
Join Date: Dec 2014
Location: Western MT.
Posts: 1,131
Likes: 5,006
Liked 1,040 Times in 438 Posts
|
|
Quote:
Originally Posted by Ivan the Butcher
I loaded 3 batches of 44-40 on my Dillon 550b, batch size was 1500. I used Bear Creek moly coated on the first batch and Patriot cast bullets on #2 & #3. All sized to .427 for Ruger Vaquero 4". The adjustment of the seating and crimp die was critical! Case length was a factor in crushed cases! I hate to admit the only way I could get consistent good ammo was to seat and crimp separately and use a Lee FCD, then production was back up to 500 per hour and 100% wrinkle free!
Ivan
BTW Midway puts the Lee Factory Crimp dies on sale a few times a year. One year on a whim, I bought 12 of them in old cartridges, just to have them. I usually don't need or like them, but when you really need one, YOU REALLY NEED ONE.
More modern cases are .015" of neck wall thickness, but 44-40, 38-40, 25-20, 32-20 and 22 Hornet are only .010" Thick. (they learned their lesson and 218 Bee is .015"!)
|
Agree 100% on the separate crimp die. I ordered some RCBS cowboy dies, and a LFCD from Midway. I seat and crimp all of my pistol cartridge's in 2 steps.
__________________
Todd
|
05-07-2020, 09:43 PM
|
|
Member
|
|
|
Join Date: Jan 2011
Location: NM home; Tbilisi work
Posts: 5,148
Likes: 11,882
Liked 11,631 Times in 3,532 Posts
|
|
Mine was .428" throats and .429" barrel. Theoretically that's a problem, but the revolver was a tack driver. Best jacked results were Sierra 200 geain JHP.
|
05-07-2020, 09:57 PM
|
Member
|
|
|
Join Date: Dec 2014
Location: Western MT.
Posts: 1,131
Likes: 5,006
Liked 1,040 Times in 438 Posts
|
|
Quote:
Originally Posted by biku324
Mine was .428" throats and .429" barrel. Theoretically that's a problem, but the revolver was a tack driver. Best jacked results were Sierra 200 geain JHP.
|
Why do you consider that a problem?
__________________
Todd
|
05-07-2020, 10:25 PM
|
|
Member
|
|
|
Join Date: Jan 2011
Location: NM home; Tbilisi work
Posts: 5,148
Likes: 11,882
Liked 11,631 Times in 3,532 Posts
|
|
My understanding is that the throats should the same size or very slightly larger that the barrel. In mine the 200 grain JHP Sierras at .4295" shot noticeably better with less primer flattening than the same case, primer, and powder charge behind a Hornady 200 grain JHP at .430". Someone who can explain the 'why' will be along, I'm sure.
I should NEVER have sold that nice revolver!
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
|
|
|
|