Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 06-01-2020, 10:24 PM
Biggie Z Biggie Z is offline
Member
.38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging  
Join Date: May 2020
Location: Central California
Posts: 5
Likes: 0
Liked 0 Times in 0 Posts
Default .38 S&W Reloads bulging

I have a British lend lease Victory model in .38 S&W and I'm trying to load some bullets for it. This is my first time reloading this cartridge and I'm having some trouble. The bullets seem to be larger in diameter than the brass because when I seat the bullets it bulges out the brass. I am using Starline .38 S&W brass, Lee .38 S&W die set, and Matt's Bullets 200 gr .361 LRN. Could this be a problem with the sizing die sizing the brass too small or am I doing something wrong? I am using the same procedure as I normally would when loading other straight wall revolver cartridges and I've never has this issue before. Any help is greatly appreciated. Thank you. Pics below:





Reply With Quote
  #2  
Old 06-02-2020, 02:18 AM
alwslate alwslate is offline
Member
.38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging  
Join Date: Dec 2009
Location: Indiana
Posts: 6,606
Likes: 3,693
Liked 7,174 Times in 2,997 Posts
Default

Maybe just the long bullet and a tight sizing die. I don't think you have
a problem as long as the loaded rounds will chamber in your gun.
Reply With Quote
The Following 5 Users Like Post:
  #3  
Old 06-02-2020, 06:01 AM
scooter123 scooter123 is offline
Member
 
Join Date: Jan 2009
Location: Metro Detroit, Michigan
Posts: 6,919
Likes: 179
Liked 4,294 Times in 2,106 Posts
Default

I would consider that perfectly normal with Lee reloading dies, they seem to be made so they size the cases at the low end of the tolerance range. Almost all of my sizing dies are Lee Carbide Dies and all show that bulge that you observed. BTW, for handguns I reload every semi caliber from 380 to 45 ACP and 38/357 Magnum and all function perfectly.
Reply With Quote
  #4  
Old 06-02-2020, 06:44 AM
stansdds stansdds is offline
Member
.38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging  
Join Date: Apr 2007
Location: Virginia
Posts: 8,713
Likes: 19,282
Liked 11,738 Times in 5,351 Posts
Default

It has been my experience that resizing dies usually reduce brass diameter to the minimum SAMMI specification, the end result are rounds that have a bit of a wasp waist appearance.
__________________
VCDL, GOA, NRA
Reply With Quote
The Following User Likes This Post:
  #5  
Old 06-02-2020, 06:53 AM
brucev brucev is offline
Member
.38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging .38 S&W Reloads bulging  
Join Date: Feb 2008
Location: The Peach State! GA!!!
Posts: 5,913
Likes: 14,218
Liked 6,250 Times in 2,325 Posts
Default

Re: OP. Normal. Should chamber in your revolver just fine. Nothing to be worried about. Sincerely. bruce.
__________________
<><
Reply With Quote
The Following User Likes This Post:
  #6  
Old 06-02-2020, 07:08 AM
oysterer's Avatar
oysterer oysterer is offline
Member
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: Feb 2016
Posts: 1,576
Likes: 1,730
Liked 2,731 Times in 868 Posts
Default

always like that
Reply With Quote
  #7  
Old 06-02-2020, 09:13 AM
gwpercle's Avatar
gwpercle gwpercle is offline
Member
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: Nov 2011
Location: Baton Rouge, La.
Posts: 6,838
Likes: 7,394
Liked 8,050 Times in 3,652 Posts
Default

The lead .361 bullets are just a little fatter than jacketed bullets , that's why you see the slight expansion . Normal and OK !
Actually that's good ... the case is gripping the bullet tightly .

If the lead bullets wants to creep forward during shooting , apply a bit of crimp to the bullet to hold it in place .

Lee carbide dies all tend to size on the tight side so they will grip the smaller diameter jacketed bullets (.360") tightly , it's common .

Loads are looking good ... it's range time !
Gary
__________________
Certified Cajun
NRA Member

Last edited by gwpercle; 06-02-2020 at 09:16 AM.
Reply With Quote
The Following User Likes This Post:
  #8  
Old 06-02-2020, 09:14 AM
Ivan the Butcher Ivan the Butcher is offline
Member
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: Jan 2008
Location: Harlem, Ohio
Posts: 14,354
Likes: 23,195
Liked 26,158 Times in 9,069 Posts
Default

I think you reloads look fine.

I bought 38 S&W loads from a commercial reloader, they shot with fantastic accuracy! The problem was he sized the cases in a 38 Special die! Every case split! (I think he tore the wall loose from the web junction on the inside!) But they were the most accurate purchased loads I ever had!

in the 30 year ago time frame: I had a box of 38 (.357) 146grain wadcutters that had the huge hollow cavity and post of Hydra-Shok fame.
I loaded 25 in 38 S&W cases with WW231 and seated the bullet out to normal overall cartridge length. In an Iver Johnson hammerless top break (heavy trigger pull) @ 25 feet all 5 shots could be covered with a 50 cent piece! I still have 25 of those bullets left!

Ivan
Reply With Quote
  #9  
Old 06-02-2020, 10:04 AM
DWalt's Avatar
DWalt DWalt is online now
Member
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,480
Likes: 236
Liked 28,944 Times in 14,013 Posts
Default

If they can be chambered, they will be OK. I have been loading .38 S&W since the early 1970s, and have always used a .38 Super resizing die and 9mm dies for neck expansion and seating. Never had noticeable case bulging. Also, I don't remember having any case splits.
Reply With Quote
The Following User Likes This Post:
  #10  
Old 06-02-2020, 12:47 PM
Nevada Ed's Avatar
Nevada Ed Nevada Ed is online now
US Veteran
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: Nov 2012
Location: Reno Nv
Posts: 13,376
Likes: 3,183
Liked 12,712 Times in 5,669 Posts
Default

Some cases have different wall thickness and case volumes, that can cause a bulge if a lead bullet is on the "Fat" side of the standard "O/D" of the bullets dia.

A die can "Size" that bullet down a little when seated if the bullet is soft enough but there might be a slight bulge if it enters "No mans land" deeper in the case, that is seldom seen by shorter bullets.

One must be careful if the bullet is seated deeper than manual spec's, since there will be higher pressures if seated deeper.

However, that round looks good to me..............
have fun.
Reply With Quote
  #11  
Old 06-02-2020, 08:19 PM
Sid V. Sid V. is offline
SWCA Member
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: Aug 2009
Location: South East Michigan
Posts: 75
Likes: 1
Liked 24 Times in 16 Posts
Default

I've had the same problem,I found the bullet seating die was the villian. I had mixed brass of varying lengths and when the roll crimp did it's job,some cases would bulge.cure is trim your case to correct length and set the die correctly. Dennis V
Reply With Quote
The Following User Likes This Post:
  #12  
Old 06-03-2020, 03:46 PM
J. R. WEEMS J. R. WEEMS is offline
Member
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: Nov 2010
Location: WINCHESTER, VIRGINIA
Posts: 3,356
Likes: 4,437
Liked 4,433 Times in 1,463 Posts
Lightbulb .38S&W

I bought the LEE dies and am not sorry. I use Missouri coated bullets and have no problem. I acquired Starline brass and in the beginning two boxes of the new Remington loadings. The Missouri bullets are .361. If I was using uncoated bullets I might look for a Lee .360 re sizing die, but dont know if it is even made.?? My guns for this are "I" frame and over 100 years old so no hot rodding of these. I ran across a case of 38 Super brass for a long sold gun and may try and use a few to make some shot shells. The brass along is of course too long, but I would be crimping them so we will see. Georgia arms makes a loading as well as others. Seems they dont have a current offering

Last edited by J. R. WEEMS; 06-06-2020 at 01:43 PM.
Reply With Quote
  #13  
Old 06-03-2020, 03:55 PM
Injunbro Injunbro is offline
Member
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: Jul 2010
Location: Arizona
Posts: 365
Likes: 3,062
Liked 779 Times in 238 Posts
Default

.38 S&W is NOT a straight walled case. Like the 9mm it's slightly tapered, in fact 9mm can be chambered in a .38 S&W but NOT FIRED SAFELY. At any rate the cases you loaded should fire form to the chambers just fine.
Reply With Quote
  #14  
Old 06-03-2020, 08:03 PM
J. R. WEEMS J. R. WEEMS is offline
Member
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: Nov 2010
Location: WINCHESTER, VIRGINIA
Posts: 3,356
Likes: 4,437
Liked 4,433 Times in 1,463 Posts
Lightbulb ANOTHER TRY

Well I ran a few of those .38 Super cases throughout a sizing die, just because I could. Then 4.0 gns of W231. Made the over the powder shot cards out of a half & half carton the wife uses in Her coffee. They have wax on them and I put that side down against the powder. #9 shot works for this loading and after crimping, every thing loaded and ejected just fine. Test firing will take place tomorrow. All looks good so far. I guess a disclaimer is in order here, so if you wish to do this you do so at your own risk.

Please allow me to add: The dipper that came with the Lees die set will take TWO scoops of #9 shot to fill the shell properly before crimping. No guesswork needed

However, as my habit, especially for such projects, all rounds were tested for fit in the gun. Because there was a bit more shot than was needed in a couple of them, I just started them through a 9mm seating die just a touch. This corrected the slight problem.

Last edited by J. R. WEEMS; 06-04-2020 at 08:16 PM.
Reply With Quote
  #15  
Old 06-03-2020, 10:28 PM
Biggie Z Biggie Z is offline
Member
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: May 2020
Location: Central California
Posts: 5
Likes: 0
Liked 0 Times in 0 Posts
Default

Thanks everyone for putting my mind at ease. They chamber fine in my revolver so I'll take them to the range and try them out. One other question, will the case bulging shorten the life of the brass?
Reply With Quote
  #16  
Old 06-04-2020, 03:16 PM
oddshooter oddshooter is offline
Member
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: Aug 2014
Location: the free state of Arizona
Posts: 1,016
Likes: 2,402
Liked 1,795 Times in 625 Posts
Default

I don't think that bulge you have will severely reduce the life span of the brass.

Most brass I lose over time is from the belling/flaring stage. It gets worked over pretty good on every loading. That's why I keep mine to the bare minimum to get the bullet in the casing without scraping.

I see more case ring bulging from trying to crimp too hard.

If you don't like that bullet being swaged down; try getting a new, larger size plug/stem for the expander die. The "nest" will be larger and not swage down the bullet.

Prescut

Last edited by oddshooter; 06-04-2020 at 03:22 PM.
Reply With Quote
  #17  
Old 06-06-2020, 01:36 PM
DWalt's Avatar
DWalt DWalt is online now
Member
.38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging .38 S&amp;W Reloads bulging  
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,480
Likes: 236
Liked 28,944 Times in 14,013 Posts
Default

Quote:
Originally Posted by Injunbro View Post
.38 S&W is NOT a straight walled case. Like the 9mm it's slightly tapered,
Bur only very slightly (less than 0.001"). And that taper is within the overall case diameter tolerance specs. If you measure case base and mouth diameters on a new .38 S&W factory round, you will probably be unable to discern any taper.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Bulging .40 cases NJM15 Reloading 30 06-02-2017 07:40 PM
Why is my factory 357 bulging? Guitarmageddon Ammo 19 01-04-2014 04:01 PM
357's BULGING? hangnoose Reloading 25 11-24-2013 09:54 AM
My Brass Is Bulging BTCat Smith & Wesson SD & Sigma Pistols 5 02-23-2013 11:05 PM
bulging barrel unclepood S&W Revolvers: 1980 to the Present 4 08-02-2009 11:01 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 07:46 PM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)