Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Ammunition-Gunsmithing > Reloading
o

Notices

Reloading All Reloading Topics Go Here


Reply
 
Thread Tools Display Modes
  #1  
Old 09-06-2021, 10:40 PM
lrrifleman's Avatar
lrrifleman lrrifleman is offline
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Oct 2015
Location: Southern NJ
Posts: 4,677
Likes: 18,927
Liked 4,185 Times in 1,862 Posts
Default A casting question

Today, I was trying to "dig out" my casting equipment from my "workshop", which I hadn't used since the summer before the accident that left me disabled, which amounted to about 15 years. In that time span, stuff just got tossed in, and to top it off, the roof of my workshop developed a leak.

Unfortunately, I discovered a pair of molds I had been using to cast bullets for my 40-65 and 45-70 Highwalls that I hadn't returned to their storage boxes. The bad news is, the exteriors of the molds have developed surface rust. The good news is that there is no rust in the mold cavities and there isn't any pitting.

Having grown up on a small truck farm, my grandfather taught me some tricks. One was to use coca cola to cut through and remove rust. Does anyone here see a problem using coca cola followed by a thorough rinse with water followed by acetone? Would anyone wish to suggest an alternate method for removing the surface rust?

As always, thanks in advance for your help!
__________________
Judge control not gun control!
Reply With Quote
The Following 3 Users Like Post:
  #2  
Old 09-06-2021, 10:50 PM
glenwolde's Avatar
glenwolde glenwolde is offline
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Apr 2012
Location: Houston, TX
Posts: 3,666
Likes: 1,566
Liked 6,195 Times in 2,270 Posts
Default

Soak them in white vinegar and rub it off.
Reply With Quote
The Following 2 Users Like Post:
  #3  
Old 09-07-2021, 01:01 AM
Ivan the Butcher Ivan the Butcher is online now
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Jan 2008
Location: Harlem, Ohio
Posts: 14,354
Likes: 23,195
Liked 26,154 Times in 9,068 Posts
Default

If the actual cavities are fine, knock off the exterior rust with a wire brush and use as is! If it needs more care, then Coke or navel jelly.

Ivan
Reply With Quote
The Following 6 Users Like Post:
  #4  
Old 09-07-2021, 01:06 AM
STCM(SW)'s Avatar
STCM(SW) STCM(SW) is offline
US Veteran
A casting question A casting question A casting question A casting question A casting question  
Join Date: Mar 2012
Location: E. Washington State
Posts: 5,475
Likes: 1,321
Liked 10,566 Times in 3,212 Posts
Default

Quote:
Originally Posted by Ivan the Butcher View Post
If the actual cavities are fine, knock off the exterior rust with a wire brush and use as is! If it needs more care, then Coke or navel jelly.

Ivan
What I have done.
__________________
Only difference Fool/Mule-ears
Reply With Quote
The Following User Likes This Post:
  #5  
Old 09-07-2021, 06:29 AM
Ruger 1,3 Ruger 1,3 is offline
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Nov 2020
Location: Texas
Posts: 1,103
Likes: 341
Liked 966 Times in 534 Posts
Default

Soak them in Kroil!
Reply With Quote
The Following 2 Users Like Post:
  #6  
Old 09-07-2021, 06:29 AM
IrishFritz IrishFritz is offline
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Dec 2020
Posts: 129
Likes: 3
Liked 254 Times in 96 Posts
Default

I believe you should not worry about external rust too much if the cavities are good and the top of the molds and the sprue plates are good. You really don't want to remove the internal heat oxide from the molds as this is an aid to casting performance. My feeling is that as you use the molds and oil them to protect them between sessions the rust will gradually slough off from the preservative oil. I know they may not look very good good but if they still work I'd leave well enough alone.
Reply With Quote
The Following 2 Users Like Post:
  #7  
Old 09-07-2021, 07:08 AM
BillBro BillBro is offline
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Apr 2019
Location: Communist maryland
Posts: 799
Likes: 228
Liked 1,151 Times in 325 Posts
Default

Not knowing anything about bullet molds and their care and maintenance all I can offer is the suggestion of THE BEST rust remover on the planet, EVAPORUST. It just flat out works like NOTHING else.

Last edited by BillBro; 09-07-2021 at 08:51 AM.
Reply With Quote
The Following 5 Users Like Post:
  #8  
Old 09-07-2021, 10:09 AM
2152hq 2152hq is offline
Member
A casting question  
Join Date: Sep 2005
Posts: 7,724
Likes: 1,633
Liked 9,091 Times in 3,362 Posts
Default

Quote:
Originally Posted by Ivan the Butcher View Post
If the actual cavities are fine, knock off the exterior rust with a wire brush and use as is! If it needs more care, then Coke or navel jelly.

Ivan
I'd follow this advise.
Stay away from the interior surfaces of the moulds, the cavities and the flat mating surfaces.
If you do apply any oil to help remove rust and old dirt, clear the oil from the blocks before casting.

Sometimes it helps after that to 'smoke' the cavity of the mould so the bullet fills out better and releases from the block(s) easier when the mould is opened.

Some use a match to apply a thin soot film.
I use a candle flame.

I don't like using a match as it carries some phosphorus and other chemicals with it from the strike ignition typical of a match.
That can cause steel to rust and pit if left over the course of a couple days.

You only have to smoke the cavity once, not on every pour. Then perhaps every so often if the bullets starts to hang up in the block when dropped or they don't want to fill completely.
Reply With Quote
The Following User Likes This Post:
  #9  
Old 09-07-2021, 11:22 AM
gwpercle's Avatar
gwpercle gwpercle is online now
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Nov 2011
Location: Baton Rouge, La.
Posts: 6,838
Likes: 7,390
Liked 8,045 Times in 3,651 Posts
Default

For the rust ... soak them in Kerosene , big box and wally world sell K-1 Kerosene for heaters and lamps in quart cans .
The kerosene will not affect the cavities .
Coke and vinegar are acids and will etch the mould cavity surfaces .
Kroil is a penetrating oil and will not damage the cavities .
A great , better than Kroil , penetrating oil is a 50-50 mix of acetone and ATF (GM Dexron , non synthetic) ... this will not damage the cavities surface but will lift and get under the rust like penetrating oils are supposed to do .

I'm glad you're back ... Stand firm and carry on .
Gary
__________________
Certified Cajun
NRA Member

Last edited by gwpercle; 09-07-2021 at 11:26 AM.
Reply With Quote
The Following 2 Users Like Post:
  #10  
Old 09-07-2021, 11:54 AM
mikerjf mikerjf is offline
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Sep 2018
Posts: 1,857
Likes: 2,232
Liked 2,929 Times in 1,090 Posts
Default

I’d say wire brush it and use it.

But just for the info, I’ll mention that a 10% solution of molasses (10% molasses and 90% water) will gently de-rust submerged parts over a month or so. It turns the rust into free black iron.
Reply With Quote
The Following User Likes This Post:
  #11  
Old 09-07-2021, 12:10 PM
4barrel's Avatar
4barrel 4barrel is offline
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Jan 2012
Location: OVER the hill in TEJAS
Posts: 2,725
Likes: 13,107
Liked 4,339 Times in 1,773 Posts
Default

Once you get the rust off --get the lead pot hot and submerge the mold for about 5 seconds. That will get the color back. <iron molds only>You may have to do it twice but don't over do it. It will look new. I have a bead blaster for rust and use sugar sand.
Reply With Quote
The Following 2 Users Like Post:
  #12  
Old 09-17-2021, 04:25 AM
Racer X Racer X is offline
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Aug 2009
Location: Seattle
Posts: 3,421
Likes: 995
Liked 3,595 Times in 1,521 Posts
Default

sodas have phosphoric acid in them, and depending, citric acid. that's why they work.
Reply With Quote
  #13  
Old 09-17-2021, 08:14 AM
cmansguns's Avatar
cmansguns cmansguns is online now
US Veteran
A casting question A casting question A casting question A casting question A casting question  
Join Date: Mar 2016
Location: Hanover, Virginia
Posts: 1,910
Likes: 3,158
Liked 5,631 Times in 1,397 Posts
Default Coke has always worked for me

OP's mention of his dad brought immediate memories to mind. Helping my high school friend with his first "car" (a 1949 Ford Business Coupe)...a real beater..****sted, needed almost everything...three on the tree with overdrive. Anyway..the clutch went out, got some parts and a new(er) pressure plate but danged if we could get those bolts out to drop that old tranny.

Car jacked up in my folks back yard, along comes pop, crawls under, takes a look and says "go get me a coke". No cans in those days, just the classic bottles, go get pop a cold one figuring he's thirsty, forget a bottle opener. Pop crawls out from under, puts the bottle top against the old rusty bumper, wham's down and bingo...top pops off. Neat trick #1 learned.

Shakes it up, thumb over the top, crawls back under and sprays the daylights out of those rusty old bolts. Maybe a half hour later, takes a breaker bar & socket, crawls back under and every bolt came loose. Wow...Neat trick # 2 learned that day.

Don't know how you would do this with modern day cans, but the pressurization and whatever chemicals are in coke (original formula only folks) sure saved the day on an old 49 Ford Tudor.
__________________
Charlie B
SWCA#3083, SWHF#570
Reply With Quote
The Following 4 Users Like Post:
  #14  
Old 09-17-2021, 09:31 AM
Greyman50's Avatar
Greyman50 Greyman50 is offline
US Veteran
A casting question A casting question A casting question A casting question A casting question  
Join Date: Apr 2021
Location: Florida
Posts: 3,716
Likes: 12,754
Liked 6,108 Times in 2,400 Posts
Default

Using most “ sodas/ soft drink” soaked rag will remove lots of minor surface rust on just about any ferrous metal. Have to watch how long you let it sit as it will remove blueing.
Reply With Quote
  #15  
Old 09-17-2021, 11:24 AM
mtgianni mtgianni is online now
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Feb 2007
Location: SW MT
Posts: 6,689
Likes: 10,392
Liked 5,970 Times in 2,940 Posts
Default

Get an old wooden pencil, yellow #2 if possible. Sharpen it and go over every inch of the exterior with the "lead" graphite. Break the point off and burnish the parts you went over with the wood. New pencils have a plastic exterior and I don't know what the material is that writes. Old pencils were Osage Orange wood in many cases. Keep wire brushes away from molds.
__________________
Front sight and squeeze
Reply With Quote
The Following 2 Users Like Post:
  #16  
Old 09-17-2021, 08:13 PM
Rifleman200-10X's Avatar
Rifleman200-10X Rifleman200-10X is offline
Member
A casting question A casting question A casting question A casting question A casting question  
Join Date: Jul 2021
Location: Papillion, Nebraska
Posts: 161
Likes: 80
Liked 557 Times in 128 Posts
Default

I have lots of vintage bullet molds, many of which were not very well cared for. But it matters not what the outside looks like, as long as the cavities are not in horrible shape. Wire brush the crud off the outside, clean and smoke the cavities, and cast away!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Newbie Question on bullet casting ChuckBen Reloading 28 03-24-2017 01:51 PM
Bullet casting question BearBio The Lounge 17 03-27-2013 11:43 AM
Looking to get into casting, bullet question David LaPell Reloading 11 01-01-2011 02:41 PM
Casting for me ? PattonTime Reloading 6 09-09-2010 12:13 PM
Casting question KingBee Reloading 5 05-08-2009 02:24 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 09:55 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)