Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Antiques
o

Notices

S&W Antiques S&W Lever Action Pistols, Tip-Up Revolvers, ALL Top-Break Revolvers, and ALL Single Shots


Reply
 
Thread Tools Display Modes
  #1  
Old 05-01-2017, 11:53 AM
Virgilmule Virgilmule is offline
Member
Rookie needs help! Rookie needs help! Rookie needs help! Rookie needs help! Rookie needs help!  
Join Date: May 2017
Posts: 2
Likes: 0
Liked 5 Times in 1 Post
Default Rookie needs help!

I recently obtained a pistol from my parents' estate that I am struggling to identify. Can anyone help? Thanks!
Attached Images
File Type: jpg IMG_5375.JPG (35.0 KB, 84 views)
File Type: jpg IMG_5377.JPG (25.7 KB, 65 views)
File Type: jpg IMG_5379.JPG (37.2 KB, 78 views)
Reply With Quote
The Following 5 Users Like Post:
  #2  
Old 05-01-2017, 12:16 PM
opoefc opoefc is offline
Absent Comrade
US Veteran
SWCA Founding Member
Rookie needs help! Rookie needs help! Rookie needs help! Rookie needs help! Rookie needs help!  
Join Date: Apr 2003
Location: San Diego, CA. USA
Posts: 10,536
Likes: 3,529
Liked 6,883 Times in 2,796 Posts
Default

Welcome to the Forum. Your S&W, serial number 115506, ( assuming that's what is says on the barrel rib ) is a .32DA, 4th model. Probably shipped from the factory around 1887-88 era. The engraving could be factory done, however most likely it was added by the distributor. Nice family heirloom! Can you parents tell you anything about it's history? You should order a factory historical letter for the gun, as it will tell you when, where and to whom the gun was shipped, as well as It;s configuration when shipped. There's a link on this Forum to the application form for a letter. Ed.

Last edited by opoefc; 05-01-2017 at 12:22 PM.
Reply With Quote
  #3  
Old 05-01-2017, 12:35 PM
Virgilmule Virgilmule is offline
Member
Rookie needs help! Rookie needs help! Rookie needs help! Rookie needs help! Rookie needs help!  
Join Date: May 2017
Posts: 2
Likes: 0
Liked 5 Times in 1 Post
Default

Ed - Thanks for the help! The serial number is stamped on the inside of the cylinder, but is nowhere to be found on the barrel. My parents are deceased, so I'm on my own digging up information. It's also interesting that inscribed into the (ivory?) handle is "Fred to Kittie". I will take your advice and send in the letter for additional historical information. Thanks again!
Reply With Quote
  #4  
Old 05-01-2017, 11:04 PM
opoefc opoefc is offline
Absent Comrade
US Veteran
SWCA Founding Member
Rookie needs help! Rookie needs help! Rookie needs help! Rookie needs help! Rookie needs help!  
Join Date: Apr 2003
Location: San Diego, CA. USA
Posts: 10,536
Likes: 3,529
Liked 6,883 Times in 2,796 Posts
Default

The serial number on the barrel is on the back end where the barrel latch is located. The numbers are very small and are stamped between the " ears". The bottom of the latch should also have the serial number stamped there. The top of the barrel should say "Smith & Wesson, Springfield, Mass." and may have various patent dates. "Fred to Kittie" adds a lot of character to the gun! The stocks are pearl. Now you have the project of finding out who Fred & Kittie may be! I once had a similar S&W with the a lady's name on it - turned out she was a famous madam in a west Texas House of Ill Repute! Ed.
Reply With Quote
  #5  
Old 05-02-2017, 09:03 AM
glowe's Avatar
glowe glowe is online now
US Veteran

Rookie needs help! Rookie needs help! Rookie needs help! Rookie needs help! Rookie needs help!  
Join Date: Nov 2009
Location: Michigan Western UP
Posts: 12,916
Likes: 3,028
Liked 14,257 Times in 5,434 Posts
Default

Welcome to the Forum. You have the information from the expert of experts and you can take it to the bank. Take Ed's advise and obtain that letter.

I do not know enough about engraving to tell you anything other than the fact that distributors did have many plain guns engraved. Distributors also provided non-factory mother-of-pearl stocks. When your 32 DA was made, pearl stocks did not yet have gold S&W medallions, so the stocks can either be factory or added by the distributor. A letter will help with both questions. The medallions appeared during the 1893 Chicago Exposition. Your revolver would have shipped from the factory around 1888.

I am quite sure you do not intend to sell the gun, but it is always a good idea to have the letter just in case. The difference between an all original factory gun and a post-factory engraved gun with non-factory stocks could add 2X to 3X to the value.
__________________
Gary
SWCA 2515
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
rookie evel knievel Reloading 7 09-06-2013 01:09 PM
Md gun rookie waz New Members Introduction 14 03-27-2013 09:01 PM
Help the rookie out? ecuFishbowl Smith & Wesson M&P 15-22 12 12-12-2011 08:16 AM
Rookie B1A New Members Introduction 11 03-05-2011 01:27 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 04:02 PM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)