|
|
05-26-2017, 10:33 PM
|
Member
|
|
|
Join Date: Apr 2016
Posts: 2
Likes: 4
Liked 2 Times in 1 Post
|
|
Need info on this gun
I have a S&W top break (?) revolver that appears to be a .32 cal. The Serial number is 85128. It is poor condition but I was hoping you could share some information about it. Model #, date manufactured, etc.
Any information would be greatly appreciated!
|
The Following 2 Users Like Post:
|
|
05-27-2017, 07:49 AM
|
Member
|
|
|
Join Date: Jun 2001
Location: Florence, Alabama, USA
Posts: 2,346
Likes: 40
Liked 1,396 Times in 772 Posts
|
|
You show a .32 Double Action, 4th Model.
Made sometime between 1883 and 1898. Maybe somebody can pin it down closer.
Very rusty, a common gun in poor condition, low resale value.
|
The Following User Likes This Post:
|
|
05-27-2017, 08:35 AM
|
|
US Veteran
|
|
|
Join Date: Nov 2009
Location: Michigan Western UP
Posts: 12,972
Likes: 3,048
Liked 14,362 Times in 5,475 Posts
|
|
Welcome to the Forum. Unfortunate storage conditions have rusted an otherwise nice old 32 DA. Bluing looks like it was once mostly there, hard rubber stocks are in good condition, and no apparent modifications have been made. Too bad about the finish, but you can improve that with some bronze steel wool and oil, which can remove most of the surface rust. The internals probably need the same treatment. The revolver would have shipped 1885-1886. At a minimum, get a good coat of oil on the surfaces both internal and external to stop the rusting from further damaging the gun, and please no wire brushes or buffing wheels.
__________________
Gary
SWCA 2515
|
The Following User Likes This Post:
|
|
05-27-2017, 08:57 AM
|
SWCA Member
|
|
|
Join Date: Feb 2014
Location: VA & SoFL
Posts: 8,692
Likes: 472
Liked 5,742 Times in 3,209 Posts
|
|
Let some oil seep under the grips before you remove. Dont put any money in it just oil and a rag for awhile. Looks like it lived on a nail in the garage or out in the shed. Just be patient and take your time. Best
__________________
Mike 2796
SoFo Bunch member
|
The Following User Likes This Post:
|
|
05-27-2017, 09:40 AM
|
|
SWCA Member
|
|
|
Join Date: Jul 2012
Location: AL Wiregrass
Posts: 7,224
Likes: 34,839
Liked 10,790 Times in 3,676 Posts
|
|
Welcome to the forums from the Wiregrass! I would drop it into an auto transmission fluid bath for several days to lift the rust. Or, if you want more penetration, make some Ed's Red Gun Bore Cleaner. If you use the Ed's Red, remove the grips first. Get some bronze wool or a copper Chore Boy scrubbing pad to go over it. Cut some of the Chore Boy, wrap around a bronze scrub brush or mop and scrub the bore. To flush the crud out of the action, use aerosol brake/carb/parts cleaner. Spray into the hammer or trigger openings until the effluent runs clear. Then lube.
__________________
Guy
SWHF #474 SWCA LM#2629
|
The Following 2 Users Like Post:
|
|
05-28-2017, 06:46 PM
|
Member
|
|
|
Join Date: Apr 2016
Posts: 2
Likes: 4
Liked 2 Times in 1 Post
|
|
Thank you all for the info!
|
|
Posting Rules
|
|
|
|
|
All times are GMT -4. The time now is 04:49 PM.