|
|
09-25-2017, 08:23 PM
|
Member
|
|
|
Join Date: Aug 2015
Posts: 41
Likes: 0
Liked 15 Times in 6 Posts
|
|
1930's M & P grips
Gentlemen, I've got an M & P .38 made approximately 1937. What grips should it have? I know the ones on it aren't original.
|
09-25-2017, 08:28 PM
|
|
Moderator
|
|
|
Join Date: Jun 2007
Posts: 26,899
Likes: 987
Liked 19,022 Times in 9,307 Posts
|
|
Service type, walnut, rounded tops with small silver medallions. Like on this gun:
Victory question
Hope this is helpful.
__________________
Alan
SWCA LM 2023, SWHF 220
|
The Following User Likes This Post:
|
|
09-25-2017, 09:32 PM
|
Member
|
|
|
Join Date: Aug 2015
Posts: 41
Likes: 0
Liked 15 Times in 6 Posts
|
|
Thank you!
|
09-25-2017, 10:05 PM
|
SWCA Member
|
|
|
Join Date: Feb 2006
Location: Pikeville, Tennessee
Posts: 6,066
Likes: 923
Liked 9,963 Times in 3,661 Posts
|
|
The service style is almost certainly correct, but if the gun is in fact circa 1937--could have been Magna's. A perhaps helpful clue (aside from the fact S&W products were not shipped in serial number order---although it figures M&P's were likely shipped about as fast as they could make them) M&P Target #659118 shipped December 12, 1936.
Ralph Tremaine
A letter will tell the tale.
Last edited by rct269; 09-25-2017 at 10:07 PM.
|
The Following User Likes This Post:
|
|
09-25-2017, 10:12 PM
|
|
US Veteran
|
|
|
Join Date: Jul 2013
Location: Southwest Iowa
Posts: 10,867
Likes: 2,688
Liked 18,970 Times in 5,589 Posts
|
|
Here is a 1939 M&P Model of 1905 Change 4 with matching stocks.
__________________
Mike
S&WCA #3065
|
The Following 4 Users Like Post:
|
|
09-25-2017, 10:18 PM
|
|
US Veteran
|
|
|
Join Date: Jul 2013
Location: Southwest Iowa
Posts: 10,867
Likes: 2,688
Liked 18,970 Times in 5,589 Posts
|
|
...and according to the SCS&W Edition 3 on page 21 it is stated
"Diamond Center Checkered Walnut, Square Butt, with flush silver medallions, used about 1929 to about 1941.
Additionally, in the summer issue of the SWCA Journal in an article on wartime changes in .38 M&P Model 1905 (fourth change) it states that there was a note on 1/1/42 that stocks changed from checkered walnut with monogram to smooth, unchecked walnut without monograms. Serial number at that time was about 880,000.
__________________
Mike
S&WCA #3065
|
09-25-2017, 11:26 PM
|
SWCA Member
|
|
|
Join Date: Feb 2006
Location: Pikeville, Tennessee
Posts: 6,066
Likes: 923
Liked 9,963 Times in 3,661 Posts
|
|
Perhaps I should have clarified K frame Magna's were available (on order) from 1936 on. That said, I'm not aware of any K frame that wore them as standard equipment.
I had a pre-war M&P Target wearing Magna's--numbered to the gun.
Ralph Tremaine
|
09-25-2017, 11:33 PM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,629
Likes: 241
Liked 29,143 Times in 14,091 Posts
|
|
I believe some of the K22/40s had Magnas and possibly the earlier K-22s had magnas. They could well have been special ordered that way. Any other K-frame from the pre-WWII period, especially run-of-the mill M&Ps, likely would not. Many later pre-war N-frame revolvers are pictured with Magnas.
Last edited by DWalt; 09-25-2017 at 11:44 PM.
|
09-25-2017, 11:35 PM
|
|
US Veteran
|
|
|
Join Date: Jul 2013
Location: Southwest Iowa
Posts: 10,867
Likes: 2,688
Liked 18,970 Times in 5,589 Posts
|
|
Ralph, I know little to nothing about Targets except they are different. The only reason I had the data on the .38 M&P is I've been trying to track down a 1930's M&P HE and finally did it last week thanks in part to those stocks. Still pumped.
__________________
Mike
S&WCA #3065
|
09-25-2017, 11:35 PM
|
|
SWCA Member Absent Comrade
|
|
|
Join Date: Jan 2014
Location: Oregon
Posts: 12,834
Likes: 10,103
Liked 27,996 Times in 8,452 Posts
|
|
Well, according to the SCSW the pre-war Magnas became available for the K-frame in 1936.
Whatever you put on your M&P is not going to be "original to the gun" anyway. So if you should be lucky enough to find a set of pre-war Magnas for a reasonable price, they will be correct for a 1937 gun.
It's just a lot more likely the gun shipped with the small service stocks. Those aren't cheap or that easy to find either, by the way.
|
09-26-2017, 01:32 AM
|
|
SWCA Member
|
|
|
Join Date: Jun 2000
Location: Massachusetts USA
Posts: 9,595
Likes: 3,711
Liked 8,949 Times in 3,556 Posts
|
|
FWIW, this topic should be moved down one forum from antiques to the hand ejector forum.
__________________
James Redfield
LM #497
|
09-26-2017, 09:37 PM
|
Member
|
|
|
Join Date: Aug 2015
Posts: 41
Likes: 0
Liked 15 Times in 6 Posts
|
|
Sorry, I thought I was in the Hand Ejectors section when I posted it.
|
09-26-2017, 09:38 PM
|
Member
|
|
|
Join Date: Aug 2015
Posts: 41
Likes: 0
Liked 15 Times in 6 Posts
|
|
By the way, since I use this one as a shooter I'd like to find some reasonably correct reproductions. Does anyone make those? I haven't had much luck online.
|
09-26-2017, 10:24 PM
|
|
Moderator
|
|
|
Join Date: Jun 2007
Posts: 26,899
Likes: 987
Liked 19,022 Times in 9,307 Posts
|
|
Some older styles of S & W stocks have been reproduced, but not this type to my knowledge. Try posting a Wanted to Buy ad here and someone should have a set.
__________________
Alan
SWCA LM 2023, SWHF 220
|
09-26-2017, 10:34 PM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,629
Likes: 241
Liked 29,143 Times in 14,091 Posts
|
|
They show up on eBay occasionally.
|
09-26-2017, 11:16 PM
|
Member
|
|
|
Join Date: Aug 2015
Posts: 41
Likes: 0
Liked 15 Times in 6 Posts
|
|
What do the pre-war Magna's look like?
|
09-26-2017, 11:54 PM
|
|
Member
|
|
|
Join Date: Aug 2008
Location: Illinois
Posts: 5,658
Likes: 15,661
Liked 7,682 Times in 2,744 Posts
|
|
Quote:
Originally Posted by Niederlander
What do the pre-war Magna's look like?
|
pre war magna grips................
__________________
There's nowt so queer as folk
|
The Following 5 Users Like Post:
|
|
09-27-2017, 02:23 AM
|
SWCA Member
|
|
|
Join Date: Oct 2007
Location: California
Posts: 19,250
Likes: 11,925
Liked 20,598 Times in 8,583 Posts
|
|
The key to determine original stocks for your gun is the rearmost side plate screw: if the screw has a domed head like the other side plate screws, it had service round top stocks. If it had Magna stocks, the rearmost screw head has a flat head.
When you look at the set of pre war stocks above it helps tp know what to look for:
1. Notice the corners of the checkering borders are pointed, post war stocks have round corners.
2. Notice the medallions are flat and chrome plated, post war they are curved to fit flush with the wood and are nickel plated.
3. Notice the upper edge or shoulder (sometimes called high, square, or sharp shouldered) are much less rounded than post war stocks.
__________________
Jim
S&WCA #819
|
The Following 3 Users Like Post:
|
|
09-27-2017, 06:50 AM
|
Member
|
|
|
Join Date: Aug 2015
Posts: 41
Likes: 0
Liked 15 Times in 6 Posts
|
|
Thank you, Gentlemen!
|
The Following User Likes This Post:
|
|
09-27-2017, 01:56 PM
|
|
US Veteran
|
|
|
Join Date: Mar 2011
Location: Palmer, Alaska
Posts: 14,500
Likes: 5,121
Liked 19,051 Times in 6,879 Posts
|
|
A couple points of clarification:
First, the prewar style Magna stocks do have a greater area of coverage with checkering and have the pointed corners mentioned by Jim. The postwar style have rounded corners and less area of coverage.
But, the early postwar style has the same sharp shoulder as the prewar Magna. The shoulder didn't get softened until about 1953.
The following picture shows two revolvers that shipped in the early postwar period. The upper gun wears the prewar style stocks that number to the gun (the assumption being that a few of these stocks survived the war and were put on very early postwar M&P revolvers). The lower gun in the picture wears the earliest style of postwar Magna stocks. The difference in the checkering is obvious and the shoulder is virtually identical.
Second, the flat head screw in the rear-most position on the sideplate didn't come into use until the late 1940s. Lots of revolvers were fitted with Magna stocks prior to that time, and the fitter would use a drill bit to make a slight hollow in the walnut to allow the stock panel to fit tightly against the frame with the rounded screw head fitting into the dimple. I have several guns like this with number-matching Magna stocks, all with the dimple. By changing to a flat head screw, this part of stock fitting became unnecessary and production time was reduced. Improving efficiency was one of Hellstrom's goals when he took over management, and it is presumed this was part of that effort. If you find a flat head screw in that position on a prewar gun, I believe it is safe to assume it isn't original. The fact that a prewar or very early postwar gun has a round head screw at the rear of the sideplate tells you nothing about the stocks that originally shipped on that gun.
__________________
Jack
SWCA #2475, SWHF #318
Last edited by JP@AK; 09-27-2017 at 01:57 PM.
|
The Following 3 Users Like Post:
|
|
09-27-2017, 04:56 PM
|
SWCA Member
|
|
|
Join Date: Oct 2007
Location: California
Posts: 19,250
Likes: 11,925
Liked 20,598 Times in 8,583 Posts
|
|
Jack,
Thanks for the correction!
__________________
Jim
S&WCA #819
|
The Following User Likes This Post:
|
|
09-27-2017, 05:12 PM
|
|
US Veteran
|
|
|
Join Date: Jul 2013
Location: Southwest Iowa
Posts: 10,867
Likes: 2,688
Liked 18,970 Times in 5,589 Posts
|
|
I always like seeing that dimple.
__________________
Mike
S&WCA #3065
|
The Following User Likes This Post:
|
|
|
Posting Rules
|
|
|
|
|