Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Hand Ejectors: 1896 to 1961
o

Notices

S&W Hand Ejectors: 1896 to 1961 All 5-Screw & Vintage 4-Screw SWING-OUT Cylinder REVOLVERS, and the 35 Autos and 32 Autos


Reply
 
Thread Tools Display Modes
  #1  
Old 11-11-2010, 02:51 PM
Nimbus Nimbus is offline
Member
Seeking Information Seeking Information Seeking Information Seeking Information Seeking Information  
Join Date: Nov 2010
Location: Western Oregon
Posts: 5
Likes: 0
Liked 0 Times in 0 Posts
Default Seeking Information

Howdy all. I am new to the forum and have a question I believe you can help me with.

I have an older, though in very good condition, S&W .38 Special. I believe it is the Military and Police model from the pre-war era. It was my grandfather’s gun and was handed down to me through my father.

I have taken pictures of the revolver and was wondering who could give me some information on it. Specifically, I am looking for approximate date of manufacture and whether it is still safe to shoot standard pressure .38 Specials through it. Thanks. Nimbus.
Reply With Quote
  #2  
Old 11-11-2010, 03:13 PM
Combat Combat is offline
US Veteran
Seeking Information Seeking Information Seeking Information Seeking Information Seeking Information  
Join Date: Mar 2006
Location: SW Ga.
Posts: 1,338
Likes: 2,250
Liked 680 Times in 220 Posts
Default

Please post the serial number off the bottom off the grip frame. We need that to give you a manufacturing date. The pics will help a lot to.
Reply With Quote
  #3  
Old 11-11-2010, 03:24 PM
Nimbus Nimbus is offline
Member
Seeking Information Seeking Information Seeking Information Seeking Information Seeking Information  
Join Date: Nov 2010
Location: Western Oregon
Posts: 5
Likes: 0
Liked 0 Times in 0 Posts
Default Seeking Information

Serial Number 90322 on the grip frame. This also matches the SN on the under side of the barrel forward of the cylinder.

I used the attach icon in the tool bar and uploaded 4 pics. Not sure where thry went though.
Attached Images
File Type: jpg IMG00006-20101111-0952[1].jpg (95.5 KB, 62 views)
File Type: jpg IMG00007-20101111-0953[1].jpg (81.1 KB, 57 views)
File Type: jpg IMG00009-20101111-0954[1].jpg (69.4 KB, 56 views)
File Type: jpg IMG00010-20101111-0955[1].jpg (73.3 KB, 53 views)
Reply With Quote
  #4  
Old 11-11-2010, 03:33 PM
Andy Griffith's Avatar
Andy Griffith Andy Griffith is offline
Member
Seeking Information Seeking Information Seeking Information Seeking Information Seeking Information  
Join Date: Dec 2005
Location: Out for the duration
Posts: 4,870
Likes: 62
Liked 520 Times in 264 Posts
Default

It looks to be in very good condition. Very nice indeed from the pictures if that is original condition- but the pin on the left of frame looks to be polished flat, and I can't tell around the hammer stud...I defer to others. I don't have my book with me, but looks to be an early 1905, but don't have the book in front of me.

Also, it looks as though the pin is missing at the bottom of the grip frame (note the little hole). This will need to be reinstalled in order for the grips to be tight on the gun- otherwise you might drop the gun while shooting it when the grips slide.
__________________
Lost it all in a boat accident

Last edited by Andy Griffith; 11-11-2010 at 03:44 PM.
Reply With Quote
  #5  
Old 11-11-2010, 03:38 PM
DCWilson's Avatar
DCWilson DCWilson is offline
SWCA Member
Seeking Information Seeking Information Seeking Information Seeking Information Seeking Information  
Join Date: Dec 2007
Location: Orange County, CA
Posts: 13,991
Likes: 4,996
Liked 7,678 Times in 2,616 Posts
Default

An oldie!

That's a Military & Police Model of 1905, First or Second Change, manufactured about 1906-07.

It is safe to shoot modern .38 Special ammunition in it as long as you avoid high velocity or overpressure loads like +P ammo. I have a gun of about this age that I regularly shoot low-speed wadcutter ammo in.

The "US SERVICE CTG" mentioned in the barrel stamping is the .38 Long Colt. A few years earlier that had been adopted as the standard military service round, and at this time was in the process of being eclipsed by the more powerful .38 S&W Special. This gun will fire both cartridges.

Your gun looks to have been refinished at some point. There is a slight softness to the corners of the frame, and the rounded ends of the hammer stud and rebound slide pin that are visible on the left side are a little flat. That happens when a gun is polished before going into the bluing tank.

Nice gun. I like the old M&Ps.
__________________
David Wilson
Reply With Quote
  #6  
Old 11-11-2010, 03:51 PM
Nimbus Nimbus is offline
Member
Seeking Information Seeking Information Seeking Information Seeking Information Seeking Information  
Join Date: Nov 2010
Location: Western Oregon
Posts: 5
Likes: 0
Liked 0 Times in 0 Posts
Default Information

Thanks all. That's exciting. It appears to be older than I thought. I went shooting with it the other day and could not believe how smooth the action was, double and single. It was also surprisingly accurate given the diminutive sights.

Looks like generation three will be enjoying this little fella. Nimbus.
Reply With Quote
Reply

Tags
colt, military, wadcutter

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
seeking Information vanO57 S&W Revolvers: 1961 to 1980 10 03-28-2017 04:18 PM
Seeking information on my revolver. christianjones S&W Hand Ejectors: 1896 to 1961 3 09-23-2015 06:24 AM
SW 38 Revovlver seeking information jamkat59 S&W Antiques 1 09-15-2014 12:58 AM
Seeking information on an old US Property marked 38 sbeduckman S&W Hand Ejectors: 1896 to 1961 7 05-08-2013 12:39 AM
Seeking information on Smith-Wessons TonyN Smith & Wesson - The Wish List 4 02-09-2009 05:10 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 12:02 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)