Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Hand Ejectors: 1896 to 1961
o

Notices

S&W Hand Ejectors: 1896 to 1961 All 5-Screw & Vintage 4-Screw SWING-OUT Cylinder REVOLVERS, and the 35 Autos and 32 Autos


Reply
 
Thread Tools Display Modes
  #1  
Old 10-10-2013, 04:57 PM
Trap Ljutic Trap Ljutic is offline
Member
Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long  
Join Date: Mar 2013
Location: Virginia
Posts: 16
Likes: 4
Liked 2 Times in 1 Post
Default Identify my .32 Long

Here is a gun that I bought several years ago, and I would like to know its model number and frame size. The first time that I showed it to my buddies, they asked if I found it in a dumpster. It has corrosion through the nickel plating several places on the frame, with much more corrosion on the cylinder. The insides of the barrel and cylinders look rough, also. I have shot this gun, and it spits lead. The timing is off a little bit; I guess that it needs a new hand. It also has real pearl grips, one of which is chipped significantly. Still, I think it is a good looking antique Smith and Wesson.
Hand Ejector.
SN 80071 star on the butt, 80071 on barrel and cylinder.
.32 Long Ctg.
Barrel lenght is 3 - 1/4 inches.
Fixed sights front and rear.
Pictures below.
Attached Images
File Type: jpg image 18.jpg (236.6 KB, 96 views)
File Type: jpg image 19.jpg (239.7 KB, 78 views)
File Type: jpg image 20.jpg (238.7 KB, 86 views)
Reply With Quote
  #2  
Old 10-10-2013, 06:21 PM
murphydog's Avatar
murphydog murphydog is offline
Moderator
Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long  
Join Date: Jun 2007
Posts: 26,782
Likes: 935
Liked 18,873 Times in 9,241 Posts
Default

This is a .32 Hand Ejector model 1903, probably shipped in 1908. The star stamping indicates a factory return for work, often but not always a refinish. If you look at the left lower grip frame there is a 5 . 26 (36?), which is when the work was done.

It is nowhere near the worst finish I've seen on a gun of that era. Hope this is helpful.
__________________
Alan
SWCA LM 2023, SWHF 220
Reply With Quote
  #3  
Old 10-11-2013, 06:58 PM
Trap Ljutic Trap Ljutic is offline
Member
Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long  
Join Date: Mar 2013
Location: Virginia
Posts: 16
Likes: 4
Liked 2 Times in 1 Post
Default

Thanks alot for the information, this is exactly what I have been wondering about.
Arthur
Reply With Quote
  #4  
Old 10-12-2013, 05:37 AM
Hondo44 Hondo44 is offline
SWCA Member

Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long  
Join Date: Oct 2007
Location: California
Posts: 19,208
Likes: 11,814
Liked 20,510 Times in 8,548 Posts
Default

Trap,

If the pearl grips were factory original, they would have gold plated S&W emblems inlayed at the top.
__________________
Jim
S&WCA #819
Reply With Quote
  #5  
Old 10-12-2013, 09:47 AM
glowe's Avatar
glowe glowe is offline
US Veteran

Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long  
Join Date: Nov 2009
Location: Michigan Western UP
Posts: 12,912
Likes: 3,028
Liked 14,247 Times in 5,432 Posts
Default

I like the old 32 HEs. Your left butt frame had what looks like a 5.20 stamped on it, and was returned to the factory in May, 1920. Technically, your revolver is not an antique, since that designation is determined by guns manufactured before 1899.

You do have a nice "vintage" S&W that will clean up with the use of a good quality polish. Many use a product called Flitz, but I prefer Meguires Scratch 2.0 polish. Give it a coat of oil or wax after done and you will be amazed how nice it will look.

I would also check ebay for a set of nice original hard rubber stocks for an I frame revolver to replace your damaged non-factory pearls when taking your gun to the range.
__________________
Gary
SWCA 2515
Reply With Quote
  #6  
Old 10-12-2013, 02:35 PM
Jaymo Jaymo is offline
Member
Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long  
Join Date: Jan 2013
Posts: 2,668
Likes: 3,512
Liked 1,578 Times in 912 Posts
Default

vintage gun grips has reproduction stocks made of polyurethane, available in a plethora of colors.
I'd use them instead of hard rubber, for range duty.
Hard rubber is brittle. And replacing original S&W hard rubber stocks is probably harder to do and more expensive than buying a set of tough polyurethane stocks.
The hard rubber are "right" for the gun. Just not always right for durability.
You can find reproductions of the S&W hard rubber stocks here:
Smith & Wesson

These appear to be the correct ones for your revolver. Make sure to measure your stocks and compare the measurements to those listed on the site.
http://www.vintagegungrips.net/ao-s10.html

I hope this helps.
I almost bought one a lot like this, but with a longer barrel and original(with a semicircular crack in the bottom of one) hard rubber stocks.
I ended up buying a 1971 or 72 36 no dash instead. The Chief's Special will be a self defense carry gun for me.
The .32 would be a range toy for me, since I already have a 31-1 3" I can use for SD, that takes the same stocks as the 36.
__________________
What would Jim Cirillo do?

Last edited by Jaymo; 10-12-2013 at 02:43 PM.
Reply With Quote
  #7  
Old 10-12-2013, 02:54 PM
JP@AK's Avatar
JP@AK JP@AK is offline
US Veteran
Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long  
Join Date: Mar 2011
Location: Palmer, Alaska
Posts: 14,477
Likes: 5,111
Liked 18,981 Times in 6,862 Posts
Default

Quote:
Originally Posted by Jaymo View Post
vintage gun grips has reproduction stocks made of polyurethane, available in a plethora of colors.
I'd use them instead of hard rubber, for range duty.
Hard rubber is brittle. And replacing original S&W hard rubber stocks is probably harder to do and more expensive than buying a set of tough polyurethane stocks.
The hard rubber are "right" for the gun. Just not always right for durability.
You can find reproductions of the S&W hard rubber stocks here:
Smith & Wesson

These appear to be the correct ones for your revolver. Make sure to measure your stocks and compare the measurements to those listed on the site.
S & W Hand Ejector .32 Check Your Grip Measurements)

I hope this helps.
I almost bought one a lot like this, but with a longer barrel and original(with a semicircular crack in the bottom of one) hard rubber stocks.
I ended up buying a 1971 or 72 36 no dash instead. The Chief's Special will be a self defense carry gun for me.
The .32 would be a range toy for me, since I already have a 31-1 3" I can use for SD, that takes the same stocks as the 36.
Trap Ljutic
I actually have a brand new pair of the reproduction stocks mentioned here by Jaymo. I have no use for them, so I would be willing to let you have them for less than those in his link. If you are interested, send me a PM and we'll work something out.
Jack
__________________
Jack
SWCA #2475, SWHF #318
Reply With Quote
  #8  
Old 10-12-2013, 10:42 PM
glowe's Avatar
glowe glowe is offline
US Veteran

Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long  
Join Date: Nov 2009
Location: Michigan Western UP
Posts: 12,912
Likes: 3,028
Liked 14,247 Times in 5,432 Posts
Default

Quote:
Originally Posted by Jaymo View Post
Hard rubber is brittle. And replacing original S&W hard rubber stocks is probably harder to do and more expensive than buying a set of tough polyurethane stocks.
The hard rubber are "right" for the gun. Just not always right for durability.
Vintage Gun Grips plastic stocks are often not the best quality. First, they are only as good as the stocks used to make their molds and some have worn checkering. Others I have tried were warped and did not fit well. The bottom pin hole was not lined up on some others. I also find that if you watch ebay, you can find original I frame stocks for the same price as reproductions after you pay for the plastic stocks and add the exorbitant cost of the screw and then shipping. I also have never had any problems with hard rubber stocks breaking or chipping unless you drop the gun or pry off the stocks.

They are, at best, copies and I will always opt for originals.
__________________
Gary
SWCA 2515
Reply With Quote
  #9  
Old 10-13-2013, 02:18 PM
Trap Ljutic Trap Ljutic is offline
Member
Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long Identify my .32 Long  
Join Date: Mar 2013
Location: Virginia
Posts: 16
Likes: 4
Liked 2 Times in 1 Post
Default

Guys: Thanks again for all of the information. That service date stamped on the frame is 5.20, May 1920. This thing is older than I ever thought.
Arthur
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
help identify 32 long DThiele S&W Hand Ejectors: 1896 to 1961 4 04-20-2017 10:51 PM
Trying to identify and get parts for a 32 long Mikeanic345 S&W Hand Ejectors: 1896 to 1961 5 02-02-2017 02:04 AM
Help Identify Revolver - .32 S&W Long crethwilm S&W Revolvers: 1961 to 1980 3 05-02-2016 08:17 AM
Help identify S&W 32 Long CTGII Forrest48 S&W Hand Ejectors: 1896 to 1961 4 10-03-2013 10:29 AM
Trying to identify and 32 Long CTG bamafan1007 S&W Hand Ejectors: 1896 to 1961 2 01-21-2012 08:03 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 08:37 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)