|
|
01-15-2016, 02:43 PM
|
Member
|
|
|
Join Date: Jun 2015
Location: NE OH
Posts: 82
Likes: 2
Liked 64 Times in 32 Posts
|
|
full cocking pre-10
I have an early 20's k-frame in decent shape. 38 Special. Main problem with it is when shooting it in single action. I really have to reef the heck out of it to get the hammer into the final aspect of full cock position. It runs real nice in double action - no problem there. Is this normal with them in single action? My other k-frames are nothing like this. What's going on?
|
01-15-2016, 02:59 PM
|
|
US Veteran
|
|
|
Join Date: Oct 2013
Location: Central Montana
Posts: 13,715
Likes: 12,858
Liked 39,476 Times in 10,046 Posts
|
|
Check it with the grips off. I have see the mainspring run into the grip screw. Shouldn't happen on factory grips. While the grips are off first check that main spring is centered in frame notch, then spray a bunch of carb or brake cleaner into the frame openings while cycling the action. After doing that for a bit a few drops of oil through same openings and it may improve.
|
01-15-2016, 03:07 PM
|
|
US Veteran
|
|
|
Join Date: Aug 2009
Location: Odessa, Texas
Posts: 3,223
Likes: 4,039
Liked 3,710 Times in 1,470 Posts
|
|
If you're used to K frames from the last 65 years you will not a difference in how far you have to pull the hammer back to cock it. The older revolvers have a longer hammer stroke than the newer ones.
|
01-15-2016, 03:37 PM
|
SWCA Member
|
|
|
Join Date: Feb 2014
Location: VA & SoFL
Posts: 8,696
Likes: 472
Liked 5,744 Times in 3,210 Posts
|
|
to the OP, help me out on "...reef...". Not familiar with the term.
__________________
Mike 2796
SoFo Bunch member
|
01-15-2016, 07:05 PM
|
|
US Veteran
|
|
|
Join Date: Oct 2013
Location: Central Montana
Posts: 13,715
Likes: 12,858
Liked 39,476 Times in 10,046 Posts
|
|
Reef is a term I hear in relationship to put out an above normal amount of force. I have heard that it was originally a slang usage that started in Australia.
The normal usage as a verb is to reef or take in a sail. Probably got transferred because in high winds a sail would take extra force to reef.
I really had to reef on the wrench to get that nut.
|
The Following 2 Users Like Post:
|
|
01-15-2016, 09:29 PM
|
Member
|
|
|
Join Date: Jun 2015
Location: NE OH
Posts: 82
Likes: 2
Liked 64 Times in 32 Posts
|
|
Reef: we used that term on a number of ships I worked on over the decades. Means like Steelslaver said. Lots of extra force. I can pull it back "normal" enough till I get to the last say 3/16 of an inch then I have to crank up the power to get the thing fully cocked. Seems weird. Haven't run into one that takes so much beef to cock fully. Grips look to be original, but who knows with an almost hundred year old piece. Will pull them off and sniff around inside --- nope, same with the grips off.
|
01-15-2016, 09:44 PM
|
Member
|
|
|
Join Date: Jun 2015
Location: NE OH
Posts: 82
Likes: 2
Liked 64 Times in 32 Posts
|
|
Okay - on a lark I pulled off the side plate - looks like the mainspring is touching the rebound slide before it's fully cocked. Is this a big deal? I don't know the innards of S&W's.
|
01-15-2016, 10:01 PM
|
|
US Veteran
|
|
|
Join Date: Oct 2013
Location: Central Montana
Posts: 13,715
Likes: 12,858
Liked 39,476 Times in 10,046 Posts
|
|
Ya, that isn't right. Something wrong. Can you post a picture.
Hey check to see that the strain screw is tight. Thats the one at the bottom of the grip. Possible if real lose to let spring work wrong.
I guess someone could have stuck in the wrong main spring at some point.
Last edited by steelslaver; 01-15-2016 at 10:07 PM.
|
01-15-2016, 11:17 PM
|
|
SWCA Member
|
|
|
Join Date: Jun 2004
Location: Mount Carmel, TN USA
Posts: 3,171
Likes: 1,628
Liked 3,178 Times in 933 Posts
|
|
Correctly working early K actions are longer than post-war short actions but are still as smooth as butter. It should not take extra force to reach full cock. Make sure the mainspring strain screw is fully seated and that it hasn't been cut off in the past. Some early shooters would modify the mainspring screw length to lighten the double-action-only action. A replacement mainspring strain screw is cheap.
__________________
Chris
SWCA #2243 SWHF #292
|
01-17-2016, 06:01 PM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,630
Likes: 241
Liked 29,143 Times in 14,091 Posts
|
|
The problem you mention can occur if the spring tensioning screw has been shortened or is not screwed in all the way. For a shortened tensioning screw, some use a fired primer cup over the tensioning screw tip to effectively lengthen it.
Last edited by DWalt; 01-17-2016 at 07:00 PM.
|
01-17-2016, 06:53 PM
|
Member
|
|
|
Join Date: Jun 2015
Location: NE OH
Posts: 82
Likes: 2
Liked 64 Times in 32 Posts
|
|
Okay - took some photos this aft of its innards. A couple (three) in sequence to show the (?) bad guy:
Well, that didn't work out so well... I hafta read up on sticking pics in here...
Last edited by noonster; 01-17-2016 at 06:54 PM.
Reason: made a mess
|
01-17-2016, 07:13 PM
|
|
Member
|
|
|
Join Date: Mar 2012
Location: Fairbanks, Alaska
Posts: 2,992
Likes: 1,026
Liked 2,937 Times in 1,078 Posts
|
|
I'm no expert, but it sounds like reefer madness to me. The main spring, whether it's been bent in the past by a do-it-yourself smithy, or is confined in its travel by a non-factory grip screw, is rubbing against something. Trial & error by someone created the problem. Trial and error can solve it. Try a new spring, new grips, new strain screw, and make sure the rebound slide stud isn't broken or loose. You can have fun fixing those old-timers, provided you don't make them worse. They're almost fool-proof. Be patient. You'll get it.
__________________
Why, I aughta.....
Last edited by Mike McLellan; 01-17-2016 at 07:41 PM.
|
01-17-2016, 07:28 PM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,630
Likes: 241
Liked 29,143 Times in 14,091 Posts
|
|
Try the trick of putting a fired primer cup over the tensioning screw tip to see if it helps. What I see from your picture is exactly what I would expect with a shortened or loosened tensioning screw. Or you might want to buy an new hammer spring and tensioning screw, as they are not expensive.
|
01-17-2016, 09:20 PM
|
Member
|
|
|
Join Date: Dec 2008
Location: Seattle
Posts: 1,947
Likes: 38
Liked 821 Times in 490 Posts
|
|
Looks to me as though you have an aftermarket mainspring, possibly not arched the same as factory. First, try the primer cup under the strain screw, and make sure you tighten the screw fully. If that doesn't solve your problem, replace the mainspring and strain screw with factory items. NOTE: If all this fails, you can CAREFULLY grind a SMALL chamfer onto the rebound slide where the contact occurs. Please do keep us posted.
Larry
Last edited by lebomm; 01-17-2016 at 09:21 PM.
|
01-17-2016, 10:07 PM
|
SWCA Member
|
|
|
Join Date: Jul 2004
Location: Inman, SC USA
Posts: 1,303
Likes: 95
Liked 649 Times in 372 Posts
|
|
I agree that the hammer spring is an non S&W part. The originals were nicely tapered from bottom to top, and straight when removed from the gun. The taper, along with a proper length strain screw gives the spring an arch that will clear the rebound slide.
__________________
Tom
1560
|
01-17-2016, 11:05 PM
|
|
SWCA Member
|
|
|
Join Date: Jun 2004
Location: Mount Carmel, TN USA
Posts: 3,171
Likes: 1,628
Liked 3,178 Times in 933 Posts
|
|
Aha! If that is an aftermarket ribbed Wolfe replacement mainspring, then I've had the same binding when putting them in pre-war guns. The little legs that hook on the stirrup get in the way on pre-war actions. You can either put an original flat mainspring back in it or carefully grind the tips off the leg hooks on the aftermarket spring.
__________________
Chris
SWCA #2243 SWHF #292
|
The Following User Likes This Post:
|
|
01-18-2016, 06:38 AM
|
|
SWCA Member
|
|
|
Join Date: Jan 2007
Location: Ashtabula County, Ohio
Posts: 6,074
Likes: 9,342
Liked 13,759 Times in 4,037 Posts
|
|
I agree that it looks like a non original spring, or at least not the original bend under tension. Try what has been mentioned and let us know what works.
I am also in Ne Ohio. PM me with where you live. If close by, I might be able to stop and look at it. I have rebuilt a few S&Ws in my time as a RO with a Police Department.
Kevin
__________________
Unshared knowledge is wasted.
|
The Following User Likes This Post:
|
|
01-18-2016, 09:32 AM
|
Member
|
|
|
Join Date: Jun 2015
Location: NE OH
Posts: 82
Likes: 2
Liked 64 Times in 32 Posts
|
|
StrawHat: see you Friday. A big thanks to the rest of you. I won't be able to work on it till later in the week - will keep you posted on any progress.
|
01-24-2016, 08:05 AM
|
|
SWCA Member
|
|
|
Join Date: Jan 2007
Location: Ashtabula County, Ohio
Posts: 6,074
Likes: 9,342
Liked 13,759 Times in 4,037 Posts
|
|
I had a chance to look inside this revolver and the mainspring does not look like a S&W. The spent primer trick did not help.
Where can we get an old style "K" mainspring for him?
Kevin
__________________
Unshared knowledge is wasted.
Last edited by StrawHat; 01-24-2016 at 08:07 AM.
|
01-24-2016, 10:46 AM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,630
Likes: 241
Liked 29,143 Times in 14,091 Posts
|
|
I don't think the K-frame spring has changed over the years. You might look on eBay or Gun Parts, Inc.(Numrich).
|
01-24-2016, 01:51 PM
|
|
SWCA Member
|
|
|
Join Date: Jul 2012
Location: AL Wiregrass
Posts: 7,224
Likes: 34,841
Liked 10,790 Times in 3,676 Posts
|
|
__________________
Guy
SWHF #474 SWCA LM#2629
|
01-24-2016, 06:24 PM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,630
Likes: 241
Liked 29,143 Times in 14,091 Posts
|
|
There are a number of Wolff K/L/N spring paks on eBay, also see one S&W spring there.
|
01-24-2016, 08:39 PM
|
|
US Veteran
|
|
|
Join Date: Aug 2006
Location: West Central IL
Posts: 22,804
Likes: 18,554
Liked 22,423 Times in 8,277 Posts
|
|
PM me your address and I'll send you a spring, but I don't have a correct strain screw. You need a longer one and I don't think the primer cup is enough to help.
__________________
H Richard
SWCA1967 SWHF244
|
The Following 2 Users Like Post:
|
|
01-25-2016, 04:02 PM
|
|
SWCA Member
|
|
|
Join Date: Jan 2007
Location: Ashtabula County, Ohio
Posts: 6,074
Likes: 9,342
Liked 13,759 Times in 4,037 Posts
|
|
After swapping a mainspring from one of my 32 WCF M&Ps, the situation resolved itself with no needed adjustment to the strain screw. So, the mainspring was not correct for the old 38 Special.
I sen a PM to H Richard and he is sending an old mainspring out to the OP and I will install it when it arrives.
Many thanks and much appreciation to H Richard.
Kevin
__________________
Unshared knowledge is wasted.
|
01-25-2016, 09:54 PM
|
Member
|
|
|
Join Date: Jun 2015
Location: NE OH
Posts: 82
Likes: 2
Liked 64 Times in 32 Posts
|
|
A big thanks to all from me, too. Looks like I'm gonna have a real fun shooter with good springs.
|
|
Posting Rules
|
|
|
|
|