|
|
10-30-2016, 11:48 AM
|
Member
|
|
|
Join Date: Oct 2016
Posts: 8
Likes: 2
Liked 3 Times in 1 Post
|
|
Identify S&W Hand Ejector revolver
I want to identify my new S&W revolver. The Model number on the frame under the yoke is 745. It is in S&W 38 Special caliber. The serial number is 2857xx. The barrel is 4". I notice it has a screw in front of the trigger guard, and the four studs in the frame are screwed in from the inside. It is nickel plated.
|
10-30-2016, 12:17 PM
|
Member
|
|
|
Join Date: Apr 2016
Posts: 1,464
Likes: 3,979
Liked 2,918 Times in 803 Posts
|
|
How about a picture, the only model 745 I can find in the S&W Standard Catalog is a semi-automatic. Also, how many screws are in the side plate? Also, if it's an early revolver, I don't believe the model number would be stamped on the frame under the yoke.
Last edited by OldChief; 10-30-2016 at 12:20 PM.
Reason: Added info.
|
10-30-2016, 01:12 PM
|
|
SWCA Member
|
|
|
Join Date: Jul 2012
Posts: 2,477
Likes: 3,790
Liked 3,912 Times in 1,196 Posts
|
|
I suspect that this is an M&P from the 19_teens, assuming there is no letter in front of the serial number. The 745 is likely an assembly number. Welcome to the forum!
|
10-30-2016, 02:12 PM
|
|
SWCA Member Absent Comrade
|
|
|
Join Date: Jan 2014
Location: Oregon
Posts: 12,834
Likes: 10,103
Liked 27,996 Times in 8,452 Posts
|
|
Without a prefix, I suspect jmace is correct, and it would be from around 1915/16. Does it look like the one pictured below? It's a .32 WCF, but based on your description should be of identical appearance.
|
The Following 2 Users Like Post:
|
|
10-30-2016, 10:55 PM
|
US Veteran Absent Comrade
|
|
|
Join Date: Mar 2005
Location: Texas
Posts: 20,361
Likes: 24,260
Liked 16,154 Times in 7,408 Posts
|
|
No models were assigned until 1957. Your gun is much older.
Probably a Military & Police, which was designated Model 10 in 1957. Some minor changes occurred along the way.
|
11-01-2016, 10:59 AM
|
Member
|
|
|
Join Date: Oct 2016
Posts: 8
Likes: 2
Liked 3 Times in 1 Post
|
|
Thanks for the replies. There are 4 screws holding the side plate. There is no S&W logo on the side plate. The nickel plating is very poor and I plan to chemically remove it and blue the gun unless this is a rare and valuable piece.
|
11-01-2016, 05:33 PM
|
|
SWCA Member
|
|
|
Join Date: Jun 2000
Location: Massachusetts USA
Posts: 9,593
Likes: 3,710
Liked 8,947 Times in 3,555 Posts
|
|
Welcome to the forum.
The problem with rarity is that sometimes it has nothing to do with the model of the gun. If in fact your gun is a M&P of which S&W made over 7,000,000 it is not really rare model wise. If however, your gun shipped to J. Edgar Hoover, it could be worth plenty.
Soooooo, unless you letter a gun, no one can really know for sure.
__________________
James Redfield
LM #497
|
11-03-2016, 12:37 PM
|
Member
|
|
|
Join Date: Oct 2016
Posts: 8
Likes: 2
Liked 3 Times in 1 Post
|
|
S&W Hand Ejector
Thanks for all the info. I believe this is a M&P made in the teens. I will let you know how the nickle strip and blueing goes.
|
11-03-2016, 02:48 PM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,597
Likes: 240
Liked 29,106 Times in 14,073 Posts
|
|
For an M&P, your SN 2857xx would indicate shipment sometime in the WWI period. I list SN 2847xx as shipping in 6/1918. The lack of the S&W logo stamp also verifies it is from the WWI period. S&W ceased using the frame logo stamp during that time, resuming use shortly after the war, sometime in 1919-20.
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
|
|
|
|