Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Hand Ejectors: 1896 to 1961
o

Notices

S&W Hand Ejectors: 1896 to 1961 All 5-Screw & Vintage 4-Screw SWING-OUT Cylinder REVOLVERS, and the 35 Autos and 32 Autos


Reply
 
Thread Tools Display Modes
  #1  
Old 04-20-2017, 10:43 PM
DSRichert DSRichert is offline
Member
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Apr 2017
Posts: 2
Likes: 1
Liked 1 Time in 1 Post
Default Help identify family hand down

Just acquired this pistol from my stepfather its missing the spring for the cylinder rod, the barrel is marked 32-20. No model # on the yoke.Any help with id and parts would be helpful and value if any. Thanks in advance20170420_071808.jpg20170420_071759.jpg20170420_071731.jpg

Sent from my LG-K330 using Tapatalk
Reply With Quote
  #2  
Old 04-20-2017, 10:59 PM
JP@AK's Avatar
JP@AK JP@AK is offline
US Veteran
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Mar 2011
Location: Palmer, Alaska
Posts: 14,477
Likes: 5,111
Liked 18,981 Times in 6,862 Posts
Default

Hi and welcome to the Forum.

What you have is a .32-20 Hand Ejector that has been heavily modified. Without the serial number, that we can speculate it was made in the 1922-1929 period. But the barrel has been chopped off and a different front sight has been attached. Also, the stocks are some sort of aftermarket replacement.

I don't know where the best place would be to find the part you need. I can tell you that the gun is a K frame. Others here may direct you to a source.
__________________
Jack
SWCA #2475, SWHF #318

Last edited by JP@AK; 04-21-2017 at 12:50 PM.
Reply With Quote
  #3  
Old 04-20-2017, 11:25 PM
Muley Gil Muley Gil is offline
US Veteran
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Feb 2005
Location: The SW Va Blue Ridge
Posts: 17,471
Likes: 88,955
Liked 24,775 Times in 8,480 Posts
Default

Welcome to the Forum.

S&W did not assign model numbers until 1957. The .32-20 chambering did not survive WW II.

Numrich Arms should be able to supply the springs you need. They will be the same as used on the pre WW II .38 special Military & Police.
__________________
John 3:16
WAR EAGLE!
Reply With Quote
  #4  
Old 04-20-2017, 11:54 PM
wheelgun610's Avatar
wheelgun610 wheelgun610 is offline
Member
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Sep 2001
Location: Grinder's Switch, TN
Posts: 1,681
Likes: 1,440
Liked 1,444 Times in 664 Posts
Default

The ejector rod shown is a later vintage part than that barrel. There should also be a number on the bottom of the barrel that matches the S/N on the butt of the grip frame. If it doesn't match, the barrel is a replacement. Check the back of the cylinder too. It should also have the same number as the butt. If they don't all match, your gun is essentially a "Franken-gun" and may need more than a spring to function correctly - and safely.

Mark
__________________
S&W Forum Member #721
Reply With Quote
  #5  
Old 04-21-2017, 12:27 AM
DCWilson's Avatar
DCWilson DCWilson is offline
SWCA Member
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Dec 2007
Location: Orange County, CA
Posts: 13,993
Likes: 4,998
Liked 7,681 Times in 2,618 Posts
Default

Notice the "P" stamp on the left side behind and above the cylinder. That's a government proof mark, and its presence suggests that this might have started out as a British Service Revolver in 1939 or 1940. The big logo on the sideplate along with the single line address points to the late '30s or early wartime years; before 1937 the logo would have been smaller and on the other side. I suspect this gun had a .32-20 barrel and cylinder substituted for the .38 S&W barrel that it would have carried originally. The jeweled treatment of hammer and trigger is not original, and the entire gun looks to me as though it was reblued at some point.

So: not a collector's item, but potentially a good shooter grade revolver for plinking and pest control.
__________________
David Wilson
Reply With Quote
The Following User Likes This Post:
  #6  
Old 04-21-2017, 09:37 AM
Wiregrassguy's Avatar
Wiregrassguy Wiregrassguy is offline
SWCA Member
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Jul 2012
Location: AL Wiregrass
Posts: 7,201
Likes: 34,555
Liked 10,739 Times in 3,659 Posts
Default

Welcome to the forums from the Wiregrass!
__________________
Guy
SWHF #474 SWCA LM#2629
Reply With Quote
  #7  
Old 04-21-2017, 10:07 AM
Absalom's Avatar
Absalom Absalom is offline
SWCA Member
Absent Comrade
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Jan 2014
Location: Oregon
Posts: 12,834
Likes: 10,103
Liked 27,995 Times in 8,452 Posts
Default

Quote:
Originally Posted by DCWilson View Post
Notice the "P" stamp on the left side behind and above the cylinder. That's a government proof mark, and its presence suggests that this might have started out as a British Service Revolver in 1939 or 1940. The big logo on the sideplate along with the single line address points to the late '30s or early wartime years; before 1937 the logo would have been smaller and on the other side. I suspect this gun had a .32-20 barrel and cylinder substituted for the .38 S&W barrel that it would have carried originally......
The P indeed can only mean that the frame was a wartime revolver, however manufactured between later 1943 and 1945. Before then, P proofs were not located there, but on the butt. While ex-BSR's were indeed much more commonly modified, the absence of any British post-war proofs makes it IMHO more likely that this gun started out as a US Victory model. Since the frames were identical and only the barrel and cylinder distinguish the two, probability is all we have, of course.
Reply With Quote
The Following User Likes This Post:
  #8  
Old 04-21-2017, 10:16 AM
DCWilson's Avatar
DCWilson DCWilson is offline
SWCA Member
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Dec 2007
Location: Orange County, CA
Posts: 13,993
Likes: 4,998
Liked 7,681 Times in 2,618 Posts
Default

Absalom, thanks for correcting and improving my hasty answer. I kind of knew when I was composing it that I was missing something, but at the time I just didn't have the energy to think it through.
__________________
David Wilson
Reply With Quote
The Following User Likes This Post:
  #9  
Old 04-21-2017, 10:35 AM
jebstuart's Avatar
jebstuart jebstuart is offline
SWCA Member
Absent Comrade
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Aug 2015
Location: Foothills (Phoenix), AZ
Posts: 624
Likes: 256
Liked 1,229 Times in 338 Posts
Default

DSRichert,
Those appear to be the original "smooth" service stocks that the revolver left the factory with, but have been (rather well laid-out but lightly cut) skip-line checkered. If you check the inside, right grip panel, the serial number might be there in hand written pencil. You will need good light to see it.
__________________
Jeb

Last edited by jebstuart; 04-21-2017 at 10:40 AM.
Reply With Quote
  #10  
Old 04-21-2017, 10:42 AM
Muley Gil Muley Gil is offline
US Veteran
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Feb 2005
Location: The SW Va Blue Ridge
Posts: 17,471
Likes: 88,955
Liked 24,775 Times in 8,480 Posts
Default

Quote:
Originally Posted by jebstuart View Post
DSRichert,
Those appear to be the original "smooth" service stocks that the revolver left the factory with, but have been (rather well done) skip-line checkered. If you check the inside, right grip panel, the serial number might be there in hand written pencil. You will need good light to see it.
If this is a British Service Revolver (BSR), the serial number will be stamped inside of the right grip.

DSRichert, could you post the serial number found on the butt? If you prefer, you can X out the last two digits. Example: V123xx. Please include any letters found on the butt. Is there a hole drilled in the butt or evidence of a plugged hole?
__________________
John 3:16
WAR EAGLE!
Reply With Quote
The Following User Likes This Post:
  #11  
Old 04-21-2017, 12:01 PM
Absalom's Avatar
Absalom Absalom is offline
SWCA Member
Absent Comrade
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Jan 2014
Location: Oregon
Posts: 12,834
Likes: 10,103
Liked 27,995 Times in 8,452 Posts
Default

I was thinking British Service Revolver myself initially when looking at the photos, especially since that front sight at first glance resembles the Parker-Hale sights which were installed on some of the BSR conversions done in Britain, but then again, a British conversion to .32-20 would be a first for me .

The number will be stamped as Muley says, not pencilled, both if the stocks belong to a BSR or a US frame.
Attached Images
File Type: jpg IMG_3663.jpg (79.7 KB, 19 views)
Reply With Quote
The Following User Likes This Post:
  #12  
Old 04-21-2017, 01:53 PM
DWalt's Avatar
DWalt DWalt is offline
Member
Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down Help identify family hand down  
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,479
Likes: 236
Liked 28,938 Times in 14,012 Posts
Default

The S&W logo on the sideplate would suggest it is post-1936. Therefore it is very likely not an original .32-20 frame, and could well be from a BSR. It is essential for a better identification that the SNs on the butt, barrel, and cylinder be provided. It's a very odd piece, and likely it has been put together from parts. Other than its personal value to you due to its family connection, its monetary value is minimal.

Last edited by DWalt; 04-21-2017 at 01:57 PM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Identify family pistol, 32 cal long, 1950s skritlebitz S&W Hand Ejectors: 1896 to 1961 21 07-26-2016 10:11 PM
please help me identify this hand me down. doubledeucefiveo S&W Hand Ejectors: 1896 to 1961 11 12-26-2015 02:01 PM
Hand ejector to identify dakotamar S&W Hand Ejectors: 1896 to 1961 19 01-15-2014 06:21 PM
Can anyone here help me date and identify an old family S&W? Ridge Runner S&W Hand Ejectors: 1896 to 1961 13 03-24-2012 12:15 PM
My family heirloom hand ejector draksia S&W Hand Ejectors: 1896 to 1961 3 06-17-2011 10:27 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 06:51 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)