I recently acquired this Smith and Wesson and ejector revolver. It appears to be model 1899 first model but I’m not a hundred percent sure. Serial number stamped under the barrel, on the cylinder and on the frame at the bottom of the butt is less than 800. It says 32 Winchester CTG on the barrel. It has adjustable sights and a 5 inch barrel. It has black hard rubber grips and a round butt. The inside surface of the crane and the opposing frame surface have the stamping 4663. It is missing the ejector. The rod and spring are there but I need the star shaped part. I also need to determine the exact caliber and proper ammunition for this firearm.

Wow, 32-20 short barrel target. One of my Grail Guns !
Photos ?
Regards,
Bruce

Welcome! You already have the ID, a .32-20 Military & Police Target model of 1899, probably a first year gun. Current factory ammunition (also called .32 Winchester Center Fire) is loaded light and should be fine to use in a sound gun.

Here is one source for it; batches are made intermittently so finding it can be a problem. It is not cheap :

Access Denied

You will need to find the extractor star specific for that gun; others here can tell you how this might differ from a later version. The ratchet (teeth on the rear face) will need to be fitted to the gun and that will require a skilled gunsmith.

__________________
Alan
SWCA LM 2023, SWHF 220

Welcome to the forum.

Check here for less expensive ammo:

HSM Cowboy Action 32-20 Winchester 115 GR RNFP

Black Hills Cowboy Action Ammo 32-20 WCF 115 Grain - MPN: DCB3220N1

.32-20 Winchester


Try here for the extractor star:

Good sources you probably use already are E-bay and Gunbroker. Set up a search for "smith wesson parts". Some listings are kits of used parts that are usually from guns destroyed by law enforcement with some to all of the parts except the frame included in the kits. You can generally win the entire parts kit for the price of the part that you want if you had bought it new.

Post an adv on this forum under the classified section.

Guns & Gun Parts Recommended by S&W
(413) 732-9938
983 Westfield St
West Springfield MA 01089-3813
EMAIL: [email protected]
Guns n Parts - New and Used Guns Bought and Sold. no parts list here.

George Dye (at David Carroll's) for old Smith parts, sight blades, etc.
‘GeorgeinSD’ is George Dye---205 502-2026 in Birmingham

"Aonepawninc" http://stores.ebay.com/aonepawninc
has a bunch of old S&W parts for sale.

Dave Bennett: Parts and guns from 1900 up to 1970's.
e-Mail: [email protected]
Web Site: www.22ammobox.com

Jack First: Large selection of Pre- and Post-WWII parts. Sells working
parts to FFL dealers only.
Phone: 605-343-9544
Reproduced firing pins for 22/32 Kit Gun and HFT

Gun Parts Corp: Successor to Numrich Arms; many guns parts.
226 Williams Lane, West Hurley, NY 12491
Phone: 845-679-2417
e-Mail: [email protected]
Web Site: www.gunpartscorp.com

Jim Horvath: Many parts for all S&W's (large and small) from 1860 up;
can reproduce parts.
e-Mail: [email protected]

Jeff Lee: Lee's Gun Parts (an extensive supply of gun parts, including S&W)
(Open to the public on Tuesdays, Wednesdays and Thursdays).
3401 W. Pioneer, Suite 2, Irving, TX 75061
Phone: 972-790-0773
http://www.leesgunparts.com/

Jan Matlega: Parts for Pre-WWII S&W hand-ejectors.
Mail Address: 528 Eddy Glover
New Britain, CT 06053
Phone: 860-229-6872

Poppert's Gun Parts: http://www.poppertsgunparts.com/
P.O. Box 413
Glenside, PA 19038
Tel: 215-887-2391 Fax: 215-887-5816
Email: [email protected]


Phil Saccacio: Phone: 540-456-6405
e-Mail: [email protected]


Mike Veilleux: Guns and Gun Parts
All Parts inc. for Pre- and Post-WWII S&W's.
Phone: 413-732-9938
e-Mail: [email protected]
Web Site: www.gunsnparts.com


Liberty Tree Collectors
Phone:207-285-3111
139 Main Street, Corinth, ME 04427
Email:[email protected]


S&W Parts; antique and new
[email protected]
Ph: 352 394-7412

"Schludershots"
https://www.schludershots.com/gun-pa...gun-parts.html

__________________
Jim
S&WCA #819

The obvious key to a Model 1899 is that there is no lug under the barrel for the ejector rod to lock into.

Does it look like this (note ejector rod, no lug), but in 5" and target sights?

__________________
H Richard
SWCA1967 SWHF244

Welcome to the forum. As you see, you came to the right place!

The general advice to anyone planning to shoot any .32-20 firearm other than a small amount occasionally is to take up reloading to avoid logistical problems associated with ammunition supply. Yours is indeed probably of first year's manufacture, but it probably shipped sometime in 1900. I don't know just how different a M1899 .32-20 extractor star differs from those used with later models (if any), but hopefully someone here may know that information. I would not buy a later .32-20 star without knowing for sure that it can be relatively easily fitted to a M1899 cylinder. Note also that .32-20 K-frames are much less common than those in .38 Special (as far fewer .32-20 revolvers were made), so you might expect some difficulty in finding a .32-20 extractor star in good condition. In any event, it would probably require the services of a gunsmith as extractor stars are generally not drop-in replacements as they must be matched and fitted carefully to the cylinder and extractor rod.

I have pictures but I can’t figure out how to post them on here

I also own a S&W model 1899 revolver in 32-20 caliber.
This 4 number s/n is also shoot able.
Great quality and tightness in this revolver.
Mine is nickle plated, with the original holster carried on duty in a Texas town.

Welcome to the forums from the Wiregrass! You have to upload pictures as attachments to your post. You can attach up to 5 each post. Below the text editing window, click on Go Advanced and click the paper clip icon in the new text editing window that opens. Browse to the pictures on your computer and select one. Repeat that up to 5 times then upload them. To verify they have uploaded, scroll down to Manage Attachments and you should see them listed there. If you still have problems, PM me and I'll give you my email address so you can send them to me for uploading for you.

__________________
Guy
SWHF #474 SWCA LM#2629