Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Hand Ejectors: 1896 to 1961
o

Notices

S&W Hand Ejectors: 1896 to 1961 All 5-Screw & Vintage 4-Screw SWING-OUT Cylinder REVOLVERS, and the 35 Autos and 32 Autos


Reply
 
Thread Tools Display Modes
  #1  
Old 05-19-2020, 08:34 AM
Pizza Bob's Avatar
Pizza Bob Pizza Bob is offline
SWCA Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Feb 2008
Location: Central NJ
Posts: 2,727
Likes: 383
Liked 5,553 Times in 1,498 Posts
Default Mystery Gun

Not sure where to put this, so I chose here as the frame falls within this time period.

I get an e-mail feed every morning from one of the major gun auction sites. This morning one of the firearms listed appears to be real “Frankengun”. Since this is an active auction, I know that it is verboten to provide a link, so you’ll have to bear with me as I describe what I found.

The seller does not identify the gun at all, they simply state that it is a pre-model – but neglect to tell you a pre-model what. It is listed under K/L frame guns and at first glance appears to be a Model 10 HB or a Model 13. However, it has adjustable sights. The rear sight is a standard S&W adjustable with the square leaf/tang, but it sits slightly proud of the top of the frame.

The front sight is a ramp that has skeletonized half-moon guards on either side of it and uses two roll-pins to secure it to the barrel – actually to a rounded rib on top of the barrel. It looks like they took a model 10 or 13 HB and enhanced/heightened the rib to raise the sight plane and give them enough “meat” to pin that strange front sight assembly.

It appears to have a target hammer and a standard trigger.

The barrel is pinned and rollmarked “38 S.&W. Special Ctg.” – so from a Model 10 HB. The listing says the caliber is .357 Magnum. The cylinder does not have rebated chambers. The 4” Heavy Barrel did not come into being until 1959 with the Model 10-1.

The frame is a 5-screw frame. The photos show a serial number on the barrel flat (under the ejector rod) and on the rear of the cylinder. The serial number, in both locations, is K140972, which correlates to 1952. But the K prefix was not used on Model 10’s, so one may surmise this started life as a K-38. The seller never shows the serial number on the butt of the gun and it is wearing speed-loader cut, checkered goncalo alves target stocks, which would be from the early 80’s onward. I'm guessing that the serial number on the barrel flat was changed to match that of the frame. The cylinder could either be original to the K-38 or also have the frame serial number added – my guess is the former. The cylinder stop stud appears to have been installed slightly rotated (flat not parallel to the recoil shield), so it was milled/filed so the correct angle was presented to the rear of the cylinder.

The work, with the exception of the cylinder stop stud, appears to be very well done. No small task to build-up and contour the rib on the barrel. The gun appears to have been re-blued, also a good job.

My only beef with this listing is the fact that it is listed as a .357 Mag – with barrel markings to the contrary. Makes me wonder if the cylinder has been re-bored and the rear face of the cylinder milled for rim clearance – not a stretch considering the rest of the work done on the gun. If it chambers a .357 round then I imagine there would be a safety issue if the cylinder started life as a .38 Spl cylinder.

They want stupid money for what is an unidentified, cobbled-up (but well-done) gun, so doubtful that it will sell – at least to a S&W knowledgeable person – but anything is possible.

Wish I could link to it, but you’re going to have find it on your own. Sorry – rules is rules.

Adios,

Pizza Bob
__________________
NRA Benefactor Member
Reply With Quote
The Following User Likes This Post:
  #2  
Old 05-19-2020, 08:38 AM
Targets Guy's Avatar
Targets Guy Targets Guy is offline
US Veteran
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Jul 2013
Location: Southwest Iowa
Posts: 10,867
Likes: 2,688
Liked 18,968 Times in 5,588 Posts
Default

Save their photos and then copy them here.
__________________
Mike
S&WCA #3065
Reply With Quote
  #3  
Old 05-19-2020, 08:42 AM
Pizza Bob's Avatar
Pizza Bob Pizza Bob is offline
SWCA Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Feb 2008
Location: Central NJ
Posts: 2,727
Likes: 383
Liked 5,553 Times in 1,498 Posts
Default

Sorry, all photos are branded with the website's name, so may be covered by copyright laws.
__________________
NRA Benefactor Member
Reply With Quote
  #4  
Old 05-19-2020, 08:48 AM
serger's Avatar
serger serger is offline
Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Dec 2014
Location: North Dakota
Posts: 824
Likes: 2,268
Liked 1,180 Times in 434 Posts
Default

I dug up the auction using search terms:

S&W K140972 auction


Interesting front sight shroud. Very nice bluing. I went to sellers
web site and looked at the picture album for the revolver.

It is nicely done but about $300.00 over priced I think.
__________________
never get out of the boat
Reply With Quote
  #5  
Old 05-19-2020, 08:49 AM
moosedog moosedog is offline
SWCA Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Feb 2003
Location: Michigan
Posts: 7,850
Likes: 11,782
Liked 13,762 Times in 3,346 Posts
Default

I saw that. The gun which the selling claims to be a 1952 gun appears to be a pre 15. A very innovated gunsmith made up some wings to make the front sight like a M-1 carbine front sight.

Picture added
Attached Images
File Type: jpg wm_14600213.jpg (139.0 KB, 245 views)

Last edited by moosedog; 05-19-2020 at 10:36 AM.
Reply With Quote
  #6  
Old 05-19-2020, 09:05 AM
target tech's Avatar
target tech target tech is offline
Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Sep 2006
Location: Western, PA
Posts: 537
Likes: 3
Liked 981 Times in 216 Posts
Default

It appears to be what is left of a wide rib "pre 14". They did a nice job cutting and recrowning the barrel. The front sight is a bit over to top, but to each their own.
Reply With Quote
  #7  
Old 05-19-2020, 09:24 AM
Art Doc's Avatar
Art Doc Art Doc is offline
SWCA Member
Absent Comrade
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Jul 2002
Location: The kidney of Dixie.
Posts: 10,509
Likes: 49
Liked 13,408 Times in 3,290 Posts
Default

FYI "Fair Use" laws allow copyrighted material to be used for educational purposes as long as no profit is involved.
__________________
No life story has happy end.
Reply With Quote
The Following User Likes This Post:
  #8  
Old 05-19-2020, 10:31 AM
red9 red9 is online now
SWCA Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Aug 2009
Location: Virginia
Posts: 1,176
Likes: 1,045
Liked 2,489 Times in 459 Posts
Default

Missouri State Police ordered some 4" heavy barrels, but I believe the serial number is too low. Probably a shortened 6" K38.

Bob
Reply With Quote
  #9  
Old 05-19-2020, 10:38 AM
sbrmike sbrmike is offline
US Veteran
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Jul 2014
Location: Potter County, PA
Posts: 357
Likes: 19
Liked 355 Times in 117 Posts
Default

Perhaps they revised the listing, but I see no mention of 357 Magnum???
They talk about 44 magnums and model 29's, but no mention of 357 Magnum that I can see. Am I missing something?
Reply With Quote
  #10  
Old 05-19-2020, 11:07 AM
Pizza Bob's Avatar
Pizza Bob Pizza Bob is offline
SWCA Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Feb 2008
Location: Central NJ
Posts: 2,727
Likes: 383
Liked 5,553 Times in 1,498 Posts
Default

Quote:
Originally Posted by sbrmike View Post
Perhaps they revised the listing, but I see no mention of 357 Magnum???
They talk about 44 magnums and model 29's, but no mention of 357 Magnum that I can see. Am I missing something?
They revised the listing. This morning it said: .357 Magnum

Looking at the pictures again, I have to agree - what I originally thought was a transplanted Model 10 heavy barrel appears to be a longer barrel cut down, based on the position of the roll mark. Would make more sense - barrel, cylinder and frame may be original. Wish they would show the serial on the grip frame and a top view of the gun.

Adios,

Pizza Bob
__________________
NRA Benefactor Member
Reply With Quote
  #11  
Old 05-19-2020, 11:23 AM
Benton Quest Benton Quest is offline
Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Dec 2010
Posts: 362
Likes: 291
Liked 593 Times in 213 Posts
Default

Little known fact...those wings were added to the front sight to assist in establishing leads whilst shooting down airplanes.

True story.

Really.

Sent from my moto g(6) using Tapatalk
Reply With Quote
The Following 2 Users Like Post:
  #12  
Old 05-19-2020, 11:33 AM
Absalom's Avatar
Absalom Absalom is offline
SWCA Member
Absent Comrade
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Jan 2014
Location: Oregon
Posts: 12,834
Likes: 10,103
Liked 27,995 Times in 8,452 Posts
Default

Quote:
Originally Posted by Art Doc View Post
FYI "Fair Use" laws allow copyrighted material to be used for educational purposes as long as no profit is involved.
Yes. What we do in threads like this clearly falls under the “criticism/comment” exemption that is covered by fair use.

And (at least if you have Windows) you can use the snipping tool to crop pictures down to the essential features you want to discuss, and leave out any identifying marks, so you do not link or even identify any auction, and you don’t violate any forum rules.
Reply With Quote
  #13  
Old 05-20-2020, 01:57 AM
GerSan69 GerSan69 is offline
Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Nov 2011
Location: metro Phoenix
Posts: 3,192
Likes: 16,363
Liked 3,962 Times in 1,603 Posts
Default

The listing includes a link to the seller's website with a few more photos, if anyone is interested.
That barrel profile looks a lot like the .38 Heavy Masterpiece. I have one of those, also in a 4" that was cut down. From my research into mine, I think everything here looks "original" to me except for the refinish, stocks, the cut barrel and the weird front sight. IMHO, $475 tops.
Reply With Quote
  #14  
Old 05-20-2020, 11:04 AM
NovaJoe NovaJoe is offline
Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Jan 2014
Location: Northern Virginia
Posts: 171
Likes: 638
Liked 155 Times in 61 Posts
Default

Before I bought that gun I would want to see what the grip frame looks like with the grips removed, and that the SN matches. Also I would ask that the price be reduced enough to pay a gunsmith to make the front sight normal again.
Reply With Quote
  #15  
Old 05-20-2020, 04:39 PM
DWalt's Avatar
DWalt DWalt is offline
Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,479
Likes: 236
Liked 28,940 Times in 14,012 Posts
Default

Quote:
Originally Posted by Benton Quest View Post
Little known fact...those wings were added to the front sight to assist in establishing leads whilst shooting down airplanes.

True story.

Really.
I have never seen any handguns with front sight wings. Can't imagine the purpose. Front sight wings like those on .30 Carbine and M1 Garand rifles were added mainly to protect the front sight blade to keep it from being knocked out of alignment. Some Finnish Moisin Nagant rifles also had very similar front sight wings. The Japanese did make early Type 99 rifles with "calipers" which stuck out from both sides of the rear sight for use against aircraft (to establish a lead). It turned out they were completely useless for that purpose and were quickly dropped. A Type 99 rifle with the AA "caliper" rear sight is very desirable today, and infrequently seen. Red Army training during WWII included using massed infantry rifle fire against low-flying aircraft, but so far as I know, the Russians never installed any AA sights on their rifles.

Last edited by DWalt; 05-20-2020 at 04:59 PM.
Reply With Quote
  #16  
Old 05-21-2020, 09:11 AM
red9 red9 is online now
SWCA Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Aug 2009
Location: Virginia
Posts: 1,176
Likes: 1,045
Liked 2,489 Times in 459 Posts
Default

Quote:
Originally Posted by Benton Quest View Post
Little known fact...those wings were added to the front sight to assist in establishing leads whilst shooting down airplanes.
Was this sight for shooting down hot air balloons?

Bob
Reply With Quote
The Following User Likes This Post:
  #17  
Old 05-21-2020, 10:37 AM
Model19man Model19man is offline
Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Jun 2011
Location: Tulsa OK
Posts: 1,401
Likes: 662
Liked 1,518 Times in 643 Posts
Default

I searched using those terms on GB and got this:

Results for S&W K140972 auction in Guns & Firearms
Save this Search
0 Items Found

Is it listed somewhere else?


Quote:
Originally Posted by serger View Post
I dug up the auction using search terms:

S&W K140972 auction


Interesting front sight shroud. Very nice bluing. I went to sellers
web site and looked at the picture album for the revolver.

It is nicely done but about $300.00 over priced I think.
Reply With Quote
  #18  
Old 05-21-2020, 11:35 AM
Benton Quest Benton Quest is offline
Member
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Dec 2010
Posts: 362
Likes: 291
Liked 593 Times in 213 Posts
Default

Quote:
Originally Posted by DWalt View Post
I have never seen any handguns with front sight wings. Can't imagine the purpose. Front sight wings like those on .30 Carbine and M1 Garand rifles were added mainly to protect the front sight blade to keep it from being knocked out of alignment. Some Finnish Moisin Nagant rifles also had very similar front sight wings. The Japanese did make early Type 99 rifles with "calipers" which stuck out from both sides of the rear sight for use against aircraft (to establish a lead). It turned out they were completely useless for that purpose and were quickly dropped. A Type 99 rifle with the AA "caliper" rear sight is very desirable today, and infrequently seen. Red Army training during WWII included using massed infantry rifle fire against low-flying aircraft, but so far as I know, the Russians never installed any AA sights on their rifles.
I actually had one of those Arisakas back in the day with the ridiculous rear sight. It had a mum on it too.

When looking at that sight, I remember thinking their reach had definitely exceeded their grasp...

Sent from my SM-T510 using Tapatalk
Reply With Quote
  #19  
Old 05-21-2020, 01:54 PM
Absalom's Avatar
Absalom Absalom is offline
SWCA Member
Absent Comrade
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Jan 2014
Location: Oregon
Posts: 12,834
Likes: 10,103
Liked 27,995 Times in 8,452 Posts
Default

Quote:
Originally Posted by Model19man View Post
I searched using those terms on GB and got this:

Results for S&W K140972 auction in Guns & Firearms
Save this Search
0 Items Found

Is it listed somewhere else?
Yes. There are quite a few other auction sites. And since we are NOT allowed to link or discuss auctions on this forum until they are closed, which this one apparently is not, I’m not going to tell you where. Sorry
Reply With Quote
  #20  
Old 05-21-2020, 03:49 PM
Art Doc's Avatar
Art Doc Art Doc is offline
SWCA Member
Absent Comrade
Mystery Gun Mystery Gun Mystery Gun Mystery Gun Mystery Gun  
Join Date: Jul 2002
Location: The kidney of Dixie.
Posts: 10,509
Likes: 49
Liked 13,408 Times in 3,290 Posts
Default

Wings protect a delicate sight.
__________________
No life story has happy end.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Ivory Mystery Grips, mystery solved goatsnguns S&W Hand Ejectors: 1896 to 1961 6 06-07-2019 11:41 PM
Md 14-2 Mystery Help mscook S&W Revolvers: 1961 to 1980 14 03-23-2018 10:42 AM
Not a Mystery Airplane, but a Mystery Rifle THE PILGRIM Firearms & Knives: Other Brands & General Gun Topics 12 09-04-2015 05:25 PM
K22 Mystery RussellD S&W Hand Ejectors: 1896 to 1961 9 06-24-2014 12:47 PM
629-4 Mystery. **final update-mystery solved** dotdsd334 S&W Revolvers: 1980 to the Present 15 10-12-2013 09:12 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 12:41 PM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)