Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Hand Ejectors: 1896 to 1961
o

Notices

S&W Hand Ejectors: 1896 to 1961 All 5-Screw & Vintage 4-Screw SWING-OUT Cylinder REVOLVERS, and the 35 Autos and 32 Autos


Reply
 
Thread Tools Display Modes
  #1  
Old 08-21-2008, 12:40 PM
cudamank cudamank is offline
Member
Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver  
Join Date: Jan 2007
Location: Peoples Republic of Calif
Posts: 260
Likes: 27
Liked 9 Times in 4 Posts
Default

I just picked up a s/w 6" in .22 long rifle and need a little help id'ing it. It has 1621 on the frame and the cylinder crane. Bottom of the barrel is marked 240086 which is also stamped on the cylinder. Under the grips on the right side is a "B" and a "0" stamped on the frame. It has some issues, the cylinder does not index all the way to the next chamber, maybe 90%, and the firing pin is broken. Also the rear site is missing a piece and a screw. Any help would be great. Thank you.





__________________
with wings as eagles
Reply With Quote
  #2  
Old 08-21-2008, 12:40 PM
cudamank cudamank is offline
Member
Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver  
Join Date: Jan 2007
Location: Peoples Republic of Calif
Posts: 260
Likes: 27
Liked 9 Times in 4 Posts
Default

I just picked up a s/w 6" in .22 long rifle and need a little help id'ing it. It has 1621 on the frame and the cylinder crane. Bottom of the barrel is marked 240086 which is also stamped on the cylinder. Under the grips on the right side is a "B" and a "0" stamped on the frame. It has some issues, the cylinder does not index all the way to the next chamber, maybe 90%, and the firing pin is broken. Also the rear site is missing a piece and a screw. Any help would be great. Thank you.





__________________
with wings as eagles
Reply With Quote
  #3  
Old 08-21-2008, 04:38 PM
Old 44 Guy Old 44 Guy is offline
Member
Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver  
Join Date: Nov 2006
Location: Sierra Nevada foothills
Posts: 5,858
Likes: 4
Liked 4,386 Times in 1,673 Posts
Default

You have a pre war S&W 22-32 Target model. It has an "I" frame. Parts are sort of hard to come by. Rear sight leaf can be made out of some thin steel. The sight screws are tiny little things, don't know the thread pitch. I've had several of these thru the years, good little trail guns. I still have one, #245,xxx that I've used for years. Beat up but accurate. Might try the used parts houses for a bolt or hand.
Reply With Quote
  #4  
Old 08-21-2008, 04:40 PM
CMcDermott CMcDermott is offline
Member
 
Join Date: Sep 2000
Location: Broomfield, CO, USA
Posts: 102
Likes: 0
Liked 0 Times in 0 Posts
Default

That is a 22/32 target model built on the "I" frame; also known as the "Beakert" model from the dealer that first ordered these from S&W. From the gold medallions in the stocks I would guess this to be a pre-WWI gun; though I haven't seen very many of these guns I don't recall ever seeing one with smooth stocks before. Usually the outlined middle area of the grips is checkered with a smooth diamond shape left around the top screw. The serial number of 240086 should also be stamped on the front of the grip frame so that it is visible with the grips in place.
As you may have guessed from the age of the gun, it will be difficult finding parts or a gunsmith who is familiar with working on your gun.
Reply With Quote
  #5  
Old 08-21-2008, 04:53 PM
dinghysailer dinghysailer is offline
Member
 
Join Date: Mar 2007
Location: the hills of New Hampshir
Posts: 102
Likes: 0
Liked 9 Times in 3 Posts
Default

225xxx shipped in September of 1915, and they phased out the gold medallions around 1920, so that pretty much brackets the ship date. I would guess towards the end of that range.
Except for the lack of checkering, the grips look right, so they are either very worn, or some one sanded them down.
Reply With Quote
  #6  
Old 08-21-2008, 05:22 PM
Jebus35745's Avatar
Jebus35745 Jebus35745 is offline
Member
Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver  
Join Date: Jun 2004
Location: Independence, OH, USA
Posts: 6,911
Likes: 28,790
Liked 7,158 Times in 2,579 Posts
Default

I have one that was missing the rear sight blade. There is someone that hangs in the gunsmith section named jaybar. You could e-mail him. I think Jim used a ruger blade in this situation on his.
Its a neat little gun. Mine is re-blued and has a bbl bulge. It shoots good and I carry it when I hunt as a back up gun for a final shot on pheasants if needed. If I should happen to drop it, oh well, its just a beater. Larry
Reply With Quote
  #7  
Old 08-21-2008, 06:01 PM
cudamank cudamank is offline
Member
Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver Help with id on .22 long rifle revolver  
Join Date: Jan 2007
Location: Peoples Republic of Calif
Posts: 260
Likes: 27
Liked 9 Times in 4 Posts
Default

Quote:
Originally posted by CMcDermott:
The serial number of 240086 should also be stamped on the front of the grip frame so that it is visible with the grips in place.
Thank you guys for the info. There is no serial number on the front of the grip frame. Looks like finding parts will be an adventure all its own.
__________________
with wings as eagles
Reply With Quote
  #8  
Old 08-21-2008, 07:50 PM
Pontiaker's Avatar
Pontiaker Pontiaker is offline
Member
 
Join Date: May 2008
Location: Fresno, CA
Posts: 809
Likes: 5
Liked 73 Times in 28 Posts
Default

I also have a couple of these, one is a Bekeart model I replaced the original bulged barrel with an early 4 inch target barrel and the other is a true 4 inch gun. Iam a knifemaker but also do some gunsmithing, mostly on old S&W,s, I can make the rear sight blade no problem.If you want me to fix it up for you let me know, my email is in my profile.Judging by the finish on the gun it looks like the checkering has just worn off the grips over the years from use...
Matt
Reply With Quote
Reply

Tags
bekeart, checkering, gunsmith, ruger, wwi

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
E22 LONG RIFLE CTG REVOLVER Ron2vettes S&W Hand Ejectors: 1896 to 1961 15 05-14-2015 08:03 AM
22 long rifle ctg revolver raytriplett S&W Revolvers: 1961 to 1980 17 12-25-2013 10:47 AM
.22 S&W Long Rifle CTG revolver help. RJones80 S&W Hand Ejectors: 1896 to 1961 12 02-04-2013 01:17 PM
S&W 22 Long Rifle CTG Revolver Digger66 S&W Revolvers: 1961 to 1980 3 04-25-2012 04:14 PM
22 long rifle ctg revolver bretts S&W Revolvers: 1961 to 1980 7 01-08-2012 03:29 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 04:14 PM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)