|
|
 |
05-15-2017, 07:15 PM
|
 |
Member
|
|
|
Join Date: Sep 2012
Location: Boston, MA USA
Posts: 388
Likes: 532
Liked 128 Times in 57 Posts
|
|
How's my pin?
Hey all! I recently picked up this Model 36 from '79 and just noticed the pin isn't exactly even on both sides. Should I have my smith take a look at this? I'd attempt to do it myself, but wasn't sure if the pin went right to left, or left to right. I'll most likely just take it to the pro though.
Oh, and I decided to wax her up tonight for a photo-shoot with my Model 10.
|
|
The Following 2 Users Like Post:
|
|
05-15-2017, 07:41 PM
|
 |
US Veteran
|
|
|
Join Date: Aug 2006
Location: West Central IL
Posts: 22,804
Likes: 18,554
Liked 22,424 Times in 8,277 Posts
|
|
If you do not feel confident to drift the pin and don't have the correct cup head punch I would agree, take it to a gunsmith that you "trust". FYI, all S&W pins are neutral, they don't have a specific drift direction.
__________________
H Richard
SWCA1967 SWHF244
|
|
The Following 2 Users Like Post:
|
|
05-15-2017, 08:20 PM
|
 |
SWCA Member
|
|
|
Join Date: May 2005
Location: Michigan
Posts: 9,320
Likes: 34,027
Liked 10,993 Times in 3,961 Posts
|
|
I had a S&W with a pin protruding on one side like yours is. I took care of it myself with good results.
You can buy the proper cupped point punch from Brownells, but since mine had a well-worn finish to start with, I just used an appropriately sized flat point punch. I put a couple of layers of masking tape all around the pin so if the punch slipped, it would hopefully not damage the finish. I used a small hammer and very lightly tapped the pin. It moved easily. Take it slow and easy or you'll make the pin protrude too much on the other side!
Of course, if my revolver looked as nice as yours, I may have taken it to a pro rather than attempt the adjustment myself. Actually, it wouldn't hurt to leave it as is, so that's what I might do.
__________________
You're shy a few manners.
Last edited by Jack Flash; 05-15-2017 at 08:21 PM.
|
|
The Following User Likes This Post:
|
|
05-15-2017, 09:04 PM
|
|
Member
|
|
|
Join Date: Sep 2012
Location: Boston, MA USA
Posts: 388
Likes: 532
Liked 128 Times in 57 Posts
|
|
Quote:
Originally Posted by H Richard
If you do not feel confident to drift the pin and don't have the correct cup head punch I would agree, take it to a gunsmith that you "trust". FYI, all S&W pins are neutral, they don't have a specific drift direction.
|
Quote:
Originally Posted by Jack Flash
I had a S&W with a pin protruding on one side like yours is. I took care of it myself with good results.
You can buy the proper cupped point punch from Brownells, but since mine had a well-worn finish to start with, I just used an appropriately sized flat point punch. I put a couple of layers of masking tape all around the pin so if the punch slipped, it would hopefully not damage the finish. I used a small hammer and very lightly tapped the pin. It moved easily. Take it slow and easy or you'll make the pin protrude too much on the other side!
Of course, if my revolver looked as nice as yours, I may have taken it to a pro rather than attempt the adjustment myself. Actually, it wouldn't hurt to leave it as is, so that's what I might do.
|
Thank you for the all info!
I think I'll have my guy take a look at it at some point, I don't want to run the risk of banging her up. I want to try and keep her looking decent for a bit. haha What do you think about shooting it in the meantime - will the pin drift any further from shooting it?
|
05-15-2017, 09:20 PM
|
|
Member
|
|
|
Join Date: Nov 2013
Posts: 610
Likes: 79
Liked 493 Times in 210 Posts
|
|
Call me Bubba, but I'd take a good heavy piece of wood dowel and put a very slight cup in the end with a drill, then use that to give it a couple of thumps with a mallet. I can't believe you'd mark it up with that, provided you had a good stable way of holding the gun.
|
|
The Following 2 Users Like Post:
|
|
05-15-2017, 09:36 PM
|
|
Banned
|
|
|
Join Date: Mar 2014
Location: Battery Oaks Range, S.C.
Posts: 1,847
Likes: 5,663
Liked 3,574 Times in 1,163 Posts
|
|
Quote:
Originally Posted by shakyshoot
Call me Bubba, but I'd take a good heavy piece of wood dowel and put a very slight cup in the end with a drill, then use that to give it a couple of thumps with a mallet. I can't believe you'd mark it up with that, provided you had a good stable way of holding the gun.
|
Hey Bubba, where you been????
|
05-16-2017, 09:26 AM
|
|
US Veteran
|
|
|
Join Date: Aug 2006
Location: West Central IL
Posts: 22,804
Likes: 18,554
Liked 22,424 Times in 8,277 Posts
|
|
Shooting it should not have any impact on the pin position. It's probably been where it is since it left the factory.
__________________
H Richard
SWCA1967 SWHF244
|
|
The Following 3 Users Like Post:
|
|
05-16-2017, 05:47 PM
|
 |
Member
|
|
|
Join Date: Jul 2014
Location: Mojave Desert
Posts: 10,381
Likes: 18,083
Liked 24,284 Times in 6,870 Posts
|
|
I used a delrin punch. Done.
|
|
The Following User Likes This Post:
|
|
05-16-2017, 06:18 PM
|
|
US Veteran
|
|
|
Join Date: Feb 2005
Location: The SW Va Blue Ridge
Posts: 17,541
Likes: 89,864
Liked 24,929 Times in 8,533 Posts
|
|
Secure the revolver in a padded vice and tap the pin with a brass punch.
__________________
John 3:16
WAR EAGLE!
|
|
The Following User Likes This Post:
|
|
05-16-2017, 06:31 PM
|
 |
Member
|
|
|
Join Date: Nov 2013
Location: Virginia
Posts: 3,147
Likes: 2,420
Liked 3,586 Times in 1,597 Posts
|
|
Well I know its attached to a very nice revolver !
|
|
The Following User Likes This Post:
|
|
|
Posting Rules
|
|
|
|
|
Linear Mode
