Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Revolvers: 1961 to 1980
o

Notices

S&W Revolvers: 1961 to 1980 3-Screw PINNED Barrel SWING-OUT Cylinder Hand Ejectors WITH Model Numbers


Reply
 
Thread Tools Display Modes
  #1  
Old 01-09-2021, 10:28 PM
PAFMAN3's Avatar
PAFMAN3 PAFMAN3 is offline
Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Jun 2014
Posts: 183
Likes: 270
Liked 83 Times in 54 Posts
Default Cleaning assistance

1st I hope this is the right forum.

I have recently inherited a couple of older revolvers, a S&W Model 36 and a Colt Official police .38 circa 1950's.

I'm looking for recommendation's on best cleaning supplies as to not damage the bluing.

While I have owed many different guns and rifles I have not owned anything pre 1980. (Except a 98 Mauser)

I would like to get the bluing to really pop so to speak. I used to use Flitz on a Ruger Mark II Target and on a GP 100 is that a good choice?

Thank you
Attached Images
File Type: jpg guns.jpg (86.2 KB, 113 views)
Reply With Quote
The Following 4 Users Like Post:
  #2  
Old 01-09-2021, 10:45 PM
6518John's Avatar
6518John 6518John is offline
SWCA Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: May 2014
Location: AR—Town & Country
Posts: 7,478
Likes: 80,268
Liked 26,096 Times in 5,948 Posts
Default

There are so many products out there it is overwhelming. I simply got an old fashioned, sealed. screw top oil can—Like you saw on the Wizard of Oz. Mix 1/2 cheapest you can find plain ATF fluid, and 1/2 acetone. That is the best solvent and lubricant I have ever used.

If you really want to make the finish shine, clean well, then get ALL the surface oil/solvent off the outside of the revolver. Apply Renwax with your finger per the instructions. You will be amazed.
__________________
Possum—The other white meat!
Reply With Quote
  #3  
Old 01-09-2021, 11:37 PM
Modified's Avatar
Modified Modified is offline
SWCA Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Apr 2012
Location: Flathead Valley, Montana
Posts: 2,814
Likes: 2,555
Liked 12,612 Times in 1,809 Posts
Default

Renwax is the way to go, avoid Flitz as it actually is removing bluing, any polish should be avoided for this reason. Something you can never really put back properly on an old gun.
Reply With Quote
The Following 2 Users Like Post:
  #4  
Old 01-09-2021, 11:54 PM
4-Screw's Avatar
4-Screw 4-Screw is offline
Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Dec 2002
Location: Illinois...via Arizona
Posts: 1,087
Likes: 659
Liked 2,029 Times in 222 Posts
Default

I use Clenzoil and then Renwax.
Reply With Quote
The Following 2 Users Like Post:
  #5  
Old 01-09-2021, 11:59 PM
lkabug's Avatar
lkabug lkabug is offline
US Veteran
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Feb 2016
Location: Piedmont of Virginia
Posts: 3,971
Likes: 4,402
Liked 5,738 Times in 2,220 Posts
Default

Renaissance Wax (Ren Wax) is great to put a protective coating on most any gun.
Clean it good. Some folks will clean the outside with Mother's mag polish. But be careful you will removed bit of bluing, and use isopropyl alcohol to remove all oil from the outside. Use a microfiber cloth to wipe down and shine. I use a cleaning patch to gently rub Ren Wax all over the gun and a microfiber to buff it off. I buff it off before it dries completely. Go light on the wax, a little goes a long way.
Reply With Quote
  #6  
Old 01-10-2021, 06:19 AM
Wiregrassguy's Avatar
Wiregrassguy Wiregrassguy is offline
SWCA Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Jul 2012
Location: AL Wiregrass
Posts: 7,201
Likes: 34,562
Liked 10,739 Times in 3,659 Posts
Default

Isopropyl alcohol will work to remove surface oil, but aerosol carb/brake/parts cleaner is quicker and probably cheaper. It's certainly more convenient.
__________________
Guy
SWHF #474 SWCA LM#2629
Reply With Quote
The Following 3 Users Like Post:
  #7  
Old 01-10-2021, 07:24 AM
StrawHat's Avatar
StrawHat StrawHat is offline
SWCA Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Jan 2007
Location: Northeast Ohio
Posts: 5,994
Likes: 9,195
Liked 13,468 Times in 3,976 Posts
Default

Search for posts by rubiranch. Kenny knows how to clean and shine a revolver and has shared his secrets.

Kevin
__________________
Unshared knowledge is wasted.
Reply With Quote
The Following 5 Users Like Post:
  #8  
Old 01-10-2021, 08:26 AM
s&wchad's Avatar
s&wchad s&wchad is offline
Moderator
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Jan 2007
Location: Great Lakes State
Posts: 29,687
Likes: 12,672
Liked 33,605 Times in 7,845 Posts
Default

Congratulations, both guns appear to be in great condition!

There's nothing wrong with Hoppe's #9 and gun oil. I've used this method for decades with good results. I't probably second nature to most members, but it may help a few new shooters. I do like Renaissance wax for long term storage, but my shooters just get a light coat of oil. Get a good pistol cleaning rod, proper fitting bronze and nylon brushes, a clean toothbrush, some patches and several soft clothes. Chambers are a different size than the bore, so it's worth having chamber and bore brushes. Brownell's carries both. I like to wear latex gloves while cleaning guns.

I suggest carefully removing the stocks/grips before you start. Scrub the bore and chambers with Hoppe's and a brush. Hoppe's will degrade bronze brushes, so it's best to use nylon brushes for this. Press the ejector rod and clean under the extractor star with the toothbrush and Hoppe's. Also go over the front of the cylinder, the frame and the outside of the barrel. Take a break and let the gun soak for awhile.

Wipe the bore and chambers with dry patches, then scrub them with a bronze brush. Run a solvent soaked patch through, then run dry patches until they come out clean. Inspect and repeat as necessary. When the bore/chambers look good, run an oily patch through them.

Wipe everything off with a clean cloth. At this point, you can either apply Ren wax or wipe all surfaces with a lightly oiled rag. Keep you oil rag in a ziplock bag and use it after handling guns.

Ren wax works great on stocks too. I use a toothbrush with very little Hoppe's to clean them, wipe them dry, apply the wax and buff it off. I keep it out of the checkering. Reinstall the stocks and admire your treasure!

If the gun sees a lot of range time, I'll pull the cylinder for cleaning. It's not rocket science, but you need to use the correct screwdriver and be careful. It's easy to slip and damage the finish.
__________________
"I also cook."

Last edited by s&wchad; 01-10-2021 at 08:31 AM.
Reply With Quote
The Following 6 Users Like Post:
  #9  
Old 01-10-2021, 09:28 AM
IrishFritz IrishFritz is offline
Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Dec 2020
Posts: 129
Likes: 3
Liked 254 Times in 96 Posts
Default

Kano Kroil ( available from Brownell's ) is a first rate penetrating oil product that will soften rust and grungy varnished oil and dirt and will even remove barrel leading. Saturate the surface and let the product work and scrub with a stiff tooth brush. It may take a while but it will work. After Kroil does its work then you can clean with denatured alcohol ( hardware store ) to remove the Kroil. You can also blow it off with carburetor or brake cleaner but be sure you have adequate ventilation as the stuff is hard on one's liver. The trick is to remove grunge chemically not mechanically as any abrasive product will remove the blue to some degree. Keep in mind that guns of this vintage may not have a particularly shiny
blue to begin with. Over the years I've had excellent results with Birchwood Casey's Barrier as a preservative and I very much agree with other fellas that a good wax is an excellent preservative and shine. You can clean the grip panels with Windex and a tooth brush followed by a light coating of tung oil.
Good luck with your project.
Reply With Quote
The Following 2 Users Like Post:
  #10  
Old 01-10-2021, 10:04 AM
VaTom VaTom is offline
Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Jul 2016
Location: SW Virginia
Posts: 2,012
Likes: 9,137
Liked 5,177 Times in 1,309 Posts
Default

As for cleaning the surface, the Flitz followed by Ren Wax treatment is the way to go. Use Flitz sparingly. I have used Flitz on a number of used rifles and handguns that I have purchased. There is always old oil buildup and maybe some very light beginnings of rust that you cant see and that dull the finish that it will remove. Here are two used revolvers that I bought in the last 7 years that were in excellent mechanical condition but finish on both were dull. One is a 1956 Colt Official Police and the other a 1979 nickel S&W Model 10.
Attached Images
File Type: jpg IMG_1441.jpg (78.0 KB, 38 views)

Last edited by VaTom; 01-10-2021 at 10:05 AM.
Reply With Quote
The Following 2 Users Like Post:
  #11  
Old 01-10-2021, 10:19 AM
PAFMAN3's Avatar
PAFMAN3 PAFMAN3 is offline
Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Jun 2014
Posts: 183
Likes: 270
Liked 83 Times in 54 Posts
Default

Quote:
Originally Posted by s&wchad View Post
Congratulations, both guns appear to be in great condition!

There's nothing wrong with Hoppe's #9 and gun oil. I've used this method for decades with good results. I't probably second nature to most members, but it may help a few new shooters. I do like Renaissance wax for long term storage, but my shooters just get a light coat of oil. Get a good pistol cleaning rod, proper fitting bronze and nylon brushes, a clean toothbrush, some patches and several soft clothes. Chambers are a different size than the bore, so it's worth having chamber and bore brushes. Brownell's carries both. I like to wear latex gloves while cleaning guns.

I suggest carefully removing the stocks/grips before you start. Scrub the bore and chambers with Hoppe's and a brush. Hoppe's will degrade bronze brushes, so it's best to use nylon brushes for this. Press the ejector rod and clean under the extractor star with the toothbrush and Hoppe's. Also go over the front of the cylinder, the frame and the outside of the barrel. Take a break and let the gun soak for awhile.

Wipe the bore and chambers with dry patches, then scrub them with a bronze brush. Run a solvent soaked patch through, then run dry patches until they come out clean. Inspect and repeat as necessary. When the bore/chambers look good, run an oily patch through them.

Wipe everything off with a clean cloth. At this point, you can either apply Ren wax or wipe all surfaces with a lightly oiled rag. Keep you oil rag in a ziplock bag and use it after handling guns.

Ren wax works great on stocks too. I use a toothbrush with very little Hoppe's to clean them, wipe them dry, apply the wax and buff it off. I keep it out of the checkering. Reinstall the stocks and admire your treasure!

If the gun sees a lot of range time, I'll pull the cylinder for cleaning. It's not rocket science, but you need to use the correct screwdriver and be careful. It's easy to slip and damage the finish.
Thank you for the very informative response.

These were my Grandfathers guns passed on to my father and now passed on to me, someday I will pass them on to my sons.
Reply With Quote
The Following 2 Users Like Post:
  #12  
Old 01-10-2021, 10:25 AM
Johnnu2 Johnnu2 is offline
Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Jan 2004
Location: NYS
Posts: 635
Likes: 0
Liked 989 Times in 362 Posts
Default

Hoppe's #9 and any oil you have handy.... 60 years and still have 'pristine' guns. Keep it simple.!!!!!!!

p.s. Keep some carpeting or other protective surface on your workshop floor so you don't drop them on a cement surface.... Cement is NOT GOOD for gun finishes.

IMHO,
J.
Reply With Quote
The Following 4 Users Like Post:
  #13  
Old 01-10-2021, 12:10 PM
gwpercle's Avatar
gwpercle gwpercle is offline
Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Nov 2011
Location: Baton Rouge, La.
Posts: 6,838
Likes: 7,394
Liked 8,050 Times in 3,652 Posts
Default

Flitz is a polishing compound and a mild abrasive ... use abrasive's carefully and sparingly because when used they can remove a little bluing . To best preserve the blue ...clean the surface with any good cleaner like Hoppes Elite Gun Cleaner ... the Elite stuff will do no harm .
After getting clean ... protect and enhance the blue with Wax ... Renwax is museum grade , expensive and not easy to find ... I use a good 100% Carnauba Wax that is made for cars.
The wax job realy makes the finish look good !
Gary
__________________
Certified Cajun
NRA Member
Reply With Quote
The Following 2 Users Like Post:
  #14  
Old 01-10-2021, 02:45 PM
VaTom VaTom is offline
Member
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Jul 2016
Location: SW Virginia
Posts: 2,012
Likes: 9,137
Liked 5,177 Times in 1,309 Posts
Default

Quote:
Originally Posted by gwpercle View Post
Flitz is a polishing compound and a mild abrasive ... use abrasive's carefully and sparingly because when used they can remove a little bluing . To best preserve the blue ...clean the surface with any good cleaner like Hoppes Elite Gun Cleaner ... the Elite stuff will do no harm .
After getting clean ... protect and enhance the blue with Wax ... Renwax is museum grade , expensive and not easy to find ... I use a good 100% Carnauba Wax that is made for cars.
The wax job realy makes the finish look good !
Gary
Agree sparingly and gently! Also - Flitz should only be used on original factory finished bluing. I bought my Ren Wax on line. The wax can also be used on the wood stocks.
Reply With Quote
The Following 2 Users Like Post:
  #15  
Old 01-10-2021, 06:43 PM
mod29's Avatar
mod29 mod29 is online now
Member
 
Join Date: Mar 2002
Location: WA
Posts: 612
Likes: 1,973
Liked 705 Times in 292 Posts
Default

Quote:
Originally Posted by Johnnu2 View Post
Hoppe's #9 and any oil you have handy.... 60 years and still have 'pristine' guns. Keep it simple.!!!!!!!

p.s. Keep some carpeting or other protective surface on your workshop floor so you don't drop them on a cement surface.... Cement is NOT GOOD for gun finishes.

IMHO,
J.

Agreed, no reason to over-think this. Hoppes #9 solvent, Hoppes gun oil and some cleaning patches and bronze bore brushes will keep those guns looking good and functioning properly.
Wipe them with oily cloth after handing and store them properly.
Reply With Quote
The Following 2 Users Like Post:
  #16  
Old 01-10-2021, 07:45 PM
Truckman's Avatar
Truckman Truckman is offline
US Veteran
Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance Cleaning assistance  
Join Date: Nov 2020
Location: Conroe Texas...
Posts: 3,902
Likes: 0
Liked 9,027 Times in 2,549 Posts
Default

Quote:
Originally Posted by VaTom View Post
As for cleaning the surface, the Flitz followed by Ren Wax treatment is the way to go.
Agreed...I add two more steps between Flitz and Renwax...I wash off the Flitz residue with WD40 which is a good cleaner in itself, but certainly not a lubricant...Then a spray down with brake cleaner followed by re-lubrication with your favorite brand...Then it's time for Renwax......Ben
__________________
Cogito, ergo BOOM!...
Reply With Quote
The Following 2 Users Like Post:
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
29-2 DOM assistance alwaysoutdoors S&W Revolvers: 1961 to 1980 2 12-20-2014 11:42 PM
Assistance please robray S&W Revolvers: 1980 to the Present 10 04-25-2013 07:12 PM
Assistance jumbeaux FORUM OFFICE 0 04-16-2013 03:24 PM
ID Assistance Please! OLDFED S&W Hand Ejectors: 1896 to 1961 1 10-16-2010 07:05 PM
GOA and GOF Asking For Our Assistance oldfella The Lounge 0 12-16-2009 08:29 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 02:34 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)