Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Revolvers: 1961 to 1980
o

Notices

S&W Revolvers: 1961 to 1980 3-Screw PINNED Barrel SWING-OUT Cylinder Hand Ejectors WITH Model Numbers


Reply
 
Thread Tools Display Modes
  #1  
Old 04-21-2021, 12:00 AM
SuperSapper SuperSapper is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Apr 2021
Location: SoCal, San diego
Posts: 16
Likes: 3
Liked 11 Times in 10 Posts
Default 19-3 cylinder open issue and hammer interference

Hi all,

This may belong in the gunsmithing forum...I wasn't sure so feel free to move if needed. Also...those are NOT live rounds in it. They are spent shell casings so the hammer doesn't fall on an empty cylinder.

First, I'm a newbie here and new owner of a 19-3. I usually am a slide gun fan, but this one seems like it will be fun to shoot. .

Only it's having a problem.

First, it's a 19-3, 6 inch barrel, and the previous owner said he removed the target hammer/trigger and replaced it with a Model 15, I believe. The narrower of the bunch (apparently there were three widths of hammer/triggers, so it appears to be the narrowest one).

To insure I did everything correctly, this was the video I watched before touching anything:

To be clear up front, I bought it knowing the problem existed, but I got a pretty good deal on it, and it does function, as I took it to the range.

First, the cylinder does not swing out when the thumb lever is pushed forward. I actually have to tap it out from the right side once I push the thumb release forward. Getting up close and personal with it, I discovered that the spring loaded pin in front of the ejector in the shroud is not going far enough back to release. A small plastic strip artificially pushing the pin back a little and the cylinder releases beautifully. How do I adjust this?

Second issue I noticed is that the thumb release seems to be just a hair too far forward, as it interferes with the hammer moving rearward when pulling the trigger. I discovered this after removing the side plate and attempting to pull the trigger. Another thread suggested some judicious file/stone work to smooth it down a bit, but can the thumb release be adjusted to bring it back enough to clear the hammer?

Lastly, perhaps it's just that it's a M15 hammer on an M19, but there seems to be a bit of binding where the sear contacts the hammer sometimes. Frequently, after pulling the trigger, the trigger does not return to forward position

Some notes:
I noticed the side plate was a bit ajar when I began to remove the screws (previous armorer I do not think did anything in this replacement process correctly) and removed the screws. Following the video one step at a time, I removed everthing, cleaned, lightly oiled, and replaced exactly as seen in the video (all the parts look the same).

Appreciate any help from the smiths out there
Mark
Attached Images
File Type: jpg Cylinder release issue.jpg (26.3 KB, 180 views)
File Type: jpg Hammer interference.jpg (25.8 KB, 197 views)
File Type: jpg Jam with sear.jpg (25.2 KB, 178 views)

Last edited by SuperSapper; 04-21-2021 at 12:18 AM.
Reply With Quote
The Following User Likes This Post:
  #2  
Old 04-21-2021, 12:30 AM
GerSan69 GerSan69 is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Nov 2011
Location: metro Phoenix
Posts: 3,192
Likes: 16,363
Liked 3,962 Times in 1,603 Posts
Default

Well, for one, that looks like an old hammer. It's not working because it doesn't fit. You need a modern hammer and trigger.
The ejector rod is likely loose. Put those empties in the chambers and try to unscrew the rod by hand. (It goes the opposite of what's "normal" - righty-loosy, lefty-tighty.)
If you choose to do the replacement yourself (I've done a few - it's not too bad) get both trigger and hammer.
The previous owner was an idiot.

Last edited by GerSan69; 04-21-2021 at 12:36 AM.
Reply With Quote
The Following User Likes This Post:
  #3  
Old 04-21-2021, 12:31 AM
Muley Gil Muley Gil is offline
US Veteran
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Feb 2005
Location: The SW Va Blue Ridge
Posts: 17,474
Likes: 88,978
Liked 24,786 Times in 8,483 Posts
Default

Generally, swapping the hammer and trigger together should fit. However, there may be just enough differences in the frames that the two parts no longer mesh perfectly. It looks like the foot of the sear may need to be shortened slightly.
__________________
John 3:16
WAR EAGLE!
Reply With Quote
The Following User Likes This Post:
  #4  
Old 04-21-2021, 12:38 AM
GerSan69 GerSan69 is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Nov 2011
Location: metro Phoenix
Posts: 3,192
Likes: 16,363
Liked 3,962 Times in 1,603 Posts
Default

Quote:
Originally Posted by Muley Gil View Post
Generally, swapping the hammer and trigger together should fit. However, there may be just enough differences in the frames that the two parts no longer mesh perfectly. It looks like the foot of the sear may need to be shortened slightly.
Gil, doesn't that look like a 1940s-vintage hammer? Or am I hallucinating from this Chinese Crud?
Reply With Quote
The Following User Likes This Post:
  #5  
Old 04-21-2021, 12:47 AM
SuperSapper SuperSapper is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Apr 2021
Location: SoCal, San diego
Posts: 16
Likes: 3
Liked 11 Times in 10 Posts
Default

I'm beginning to get the sense that the previous owner (who was a decent guy who had an armorer do the work) may have been less than diligent with who did the work.

And just looking at what's here, the armorer was an idiot.
Reply With Quote
The Following User Likes This Post:
  #6  
Old 04-21-2021, 12:49 AM
schutz5 schutz5 is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Mar 2013
Posts: 627
Likes: 506
Liked 576 Times in 317 Posts
Default

Looks like a vintage hammer spur to me!
Reply With Quote
The Following 2 Users Like Post:
  #7  
Old 04-21-2021, 01:07 AM
Muley Gil Muley Gil is offline
US Veteran
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Feb 2005
Location: The SW Va Blue Ridge
Posts: 17,474
Likes: 88,978
Liked 24,786 Times in 8,483 Posts
Default

Looks like a fishhook hammer!
__________________
John 3:16
WAR EAGLE!
Reply With Quote
The Following User Likes This Post:
  #8  
Old 04-21-2021, 02:18 AM
SuperSapper SuperSapper is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Apr 2021
Location: SoCal, San diego
Posts: 16
Likes: 3
Liked 11 Times in 10 Posts
Default

Quote:
Originally Posted by GerSan69 View Post
Well, for one, that looks like an old hammer. It's not working because it doesn't fit. You need a modern hammer and trigger.
The ejector rod is likely loose. Put those empties in the chambers and try to unscrew the rod by hand. (It goes the opposite of what's "normal" - righty-loosy, lefty-tighty.)
If you choose to do the replacement yourself (I've done a few - it's not too bad) get both trigger and hammer.
The previous owner was an idiot.
So I took a look at the ejector rod. It's not loose. It's screwed all the way down and seated right at the mating surface of the other half of the extractor and still there is this much depth to the internal part. See pic.

When I push the pin in front (simulating activating the cylinder thumb release), there is still a lip (about 1 mm) which I suspect the spring loaded pin at the front of the shroud is hanging up on. In fact, that's exactly what's happening. So my next question is:

Which part do I replace or trim? The spring loaded pin at the front of the shroud that inserts into the ejector rod? Or do I replace the ejector rod because the center part (at the arrow in the pic) is too short? Or is there some sort of 3rd option I'm missing?

Thanks for all the help.
Attached Images
File Type: jpg Rod depth.jpg (19.7 KB, 79 views)
Reply With Quote
The Following User Likes This Post:
  #9  
Old 04-21-2021, 02:52 AM
Gunhacker's Avatar
Gunhacker Gunhacker is offline
SWCA Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Oct 2002
Location: SF East Bay - "the delta"
Posts: 3,508
Likes: 1,585
Liked 4,495 Times in 1,516 Posts
Default

With the cylinder open, can you press on the front locking bolt (the pin in front of the ejector rod) with a punch or the end of a tooth brush handle, and get it to fully retract into the hole it protrudes from?

If not, or it feels like there's more than spring resistance, chances are there is a build up crud in that channel that is preventing the front bolt from retracting far enough to allow the ejector rod to unlatch.

I had that issue with a used 586 I bought, a good cleaning with an aerosol gun cleaner blasted loose a surprising amount of caked powder residue out of that bolt channel. Once cleaned, it fixed my cylinder release problem.

Don't mess with the front of the ejector rod, there needs to be a certain amount of engagement with the front locking bolt, and what you describe sounds normal.
__________________
Conrad
SWCA #1830 SWHF #222

Last edited by Gunhacker; 04-21-2021 at 03:02 AM.
Reply With Quote
The Following User Likes This Post:
  #10  
Old 04-21-2021, 04:23 AM
GerSan69 GerSan69 is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Nov 2011
Location: metro Phoenix
Posts: 3,192
Likes: 16,363
Liked 3,962 Times in 1,603 Posts
Default

Quote:
Originally Posted by SuperSapper View Post
So I took a look at the ejector rod. It's not loose. It's screwed all the way down and seated right at the mating surface of the other half of the extractor and still there is this much depth to the internal part. See pic.

When I push the pin in front (simulating activating the cylinder thumb release), there is still a lip (about 1 mm) which I suspect the spring loaded pin at the front of the shroud is hanging up on. In fact, that's exactly what's happening. So my next question is:

Which part do I replace or trim? The spring loaded pin at the front of the shroud that inserts into the ejector rod? Or do I replace the ejector rod because the center part (at the arrow in the pic) is too short? Or is there some sort of 3rd option I'm missing?

Thanks for all the help.
My pleasure.
I think Gunhacker has the most likely answer. Definitely worth a try, and you always want to rule out all non-destructive possibilities (that don't require cutting) first. I can say with a high degree of certainty trimming will not be needed.
Fishhook hammer! That's the name I couldn't remember earlier. Properly called the "Speed Hammer," it was used in the late 1940s - mid 1950s. Definitely the wrong one for your gun, as you have discovered. Try Ebay, Brownell's, Numrich, or any of the other gun parts web sites. My personal favorite, and one I've used before, is USA Guns and Gear, Smith and Wesson Revolver Parts & Pistol Parts For Sale – USA Guns And Gear-Your Favorite Gun Parts Store
Prompt service and I've always received good, clean parts from them. I really do suggest getting a trigger and hammer, BTW.
So there ya go. Too bad the seller was not too sharp on what he had, but you got a darn nice looking revolver out of the deal. And if you didn't pay too much, your additional outlay for parts won't sting so bad. Good luck!
Reply With Quote
The Following 2 Users Like Post:
  #11  
Old 04-21-2021, 08:31 AM
RGNewell's Avatar
RGNewell RGNewell is offline
SWCA Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Oct 2012
Location: San Antonio, Texas
Posts: 978
Likes: 489
Liked 2,132 Times in 518 Posts
Default

One other possibility is that the center pin is too short. You can probably get a longer one and trim it to proper length.

Sent from my SM-N986U using Tapatalk
Reply With Quote
The Following 3 Users Like Post:
  #12  
Old 04-21-2021, 07:26 PM
SuperSapper SuperSapper is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Apr 2021
Location: SoCal, San diego
Posts: 16
Likes: 3
Liked 11 Times in 10 Posts
Default

Quote:
Originally Posted by Gunhacker View Post
With the cylinder open, can you press on the front locking bolt (the pin in front of the ejector rod) with a punch or the end of a tooth brush handle, and get it to fully retract into the hole it protrudes from?

If not, or it feels like there's more than spring resistance, chances are there is a build up crud in that channel that is preventing the front bolt from retracting far enough to allow the ejector rod to unlatch.

I had that issue with a used 586 I bought, a good cleaning with an aerosol gun cleaner blasted loose a surprising amount of caked powder residue out of that bolt channel. Once cleaned, it fixed my cylinder release problem.

Don't mess with the front of the ejector rod, there needs to be a certain amount of engagement with the front locking bolt, and what you describe sounds normal.
I took the entire assembly apart and cleaned it very thoroughly. The ejector rod fully retracts easily, but when pushed back and sitting flush with the cylinder, there is a small lip at the rear of the ejector rod. It is as if the part inside the ejector rod that is pushed back when you push the cylinder release forward (to open the cylinder) is too short.

I can't imagine any reason to replace it. Do they get damaged by breaking off a part such that they are short and need to be replaced? It doesn't look damaged, even under a magnifying glass.

Since the hammer and trigger aren't original to the gun, is there any reason the rod inside would need to be replaced. I attached the pic again to show what we're talking about.

Mark
Attached Images
File Type: jpg IMG_1195.jpg (121.8 KB, 72 views)
Reply With Quote
The Following User Likes This Post:
  #13  
Old 04-21-2021, 09:09 PM
19leben's Avatar
19leben 19leben is offline
SWCA Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Jan 2015
Location: Oklahoma
Posts: 1,240
Likes: 3,588
Liked 1,956 Times in 532 Posts
Default

Something I noticed with a M15 Combat Masterpiece that I was considering locally: it was extremely difficult to release and swing out the cylinder. Finally, after many difficult open/close operations, as I inspected all the parts that affect the action, I noticed that the rear end (the part that is directly in contact with the thumb release) of the cylinder center pin was FLAT. Not sure how this came to be.. Every instance of my experiences with S&W revolvers reminded me that the center pin is radius, and just a tad longer. This is something to consider.

Sent from my SM-G975U using Tapatalk
Reply With Quote
The Following User Likes This Post:
  #14  
Old 04-22-2021, 12:49 AM
GerSan69 GerSan69 is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Nov 2011
Location: metro Phoenix
Posts: 3,192
Likes: 16,363
Liked 3,962 Times in 1,603 Posts
Default

Quote:
Originally Posted by SuperSapper View Post
I took the entire assembly apart and cleaned it very thoroughly. The ejector rod fully retracts easily, but when pushed back and sitting flush with the cylinder, there is a small lip at the rear of the ejector rod. It is as if the part inside the ejector rod that is pushed back when you push the cylinder release forward (to open the cylinder) is too short.
I can't imagine any reason to replace it. Do they get damaged by breaking off a part such that they are short and need to be replaced? It doesn't look damaged, even under a magnifying glass.
Since the hammer and trigger aren't original to the gun, is there any reason the rod inside would need to be replaced. I attached the pic again to show what we're talking about. Mark
You mentioned "a small lip at the rear of the ejector rod". I was wondering what you mean. Is there a sharp edge catching something, or ?
Please don't keep thinking that any part is "too short," "broken," or anything else. Damage in that area is almost always from abuse, so it's not something that will naturally occur. That also means it's rare.
Do you have a reputable gunsmith nearby that can advise you on this? Revolvers do have some somewhat complicated mechanisms in them, and unless you are thoroughly familiar, you can do more harm than good. As a "good Forum member," I want to see folks that come on here are able to enjoy their firearms, not get into a situation that costs them money needlessly.
Reply With Quote
The Following User Likes This Post:
  #15  
Old 04-22-2021, 01:20 AM
dsf dsf is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Jan 2006
Location: Escaping CA to OR in 2024
Posts: 1,166
Likes: 1,141
Liked 1,424 Times in 577 Posts
Default

The cylinder thumblatch and the rear of the hammer rubbing against the cylinder catch inside the action may be related, and may result in part from the previous owner trying to correct a problem, real or imagined, with the center pin.

The base of the cylinder thumblatch drops into a slot in the frame (left side) and is held in by a threaded nut. It has a certain amount of "meat" up front that stops its forward travel. The front of the thumblatch should not touch the recoil shield.

An easy starting point is to purchase a new thumblatch and drop it in. Then get the correct hammer and trigger.

FWIW, what you are referring to the "rear" is actually the front of the ejector rod and center pin. That inner steel rod is referred to as the center pin. This schematic helps alot:

Smith & Wesson 19-3 Revolver Parts, Schematics | Numrich Gun Parts

Check out the hammers and triggers listed.

Last edited by dsf; 04-22-2021 at 01:30 AM.
Reply With Quote
The Following 2 Users Like Post:
  #16  
Old 04-22-2021, 01:33 AM
dsf dsf is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Jan 2006
Location: Escaping CA to OR in 2024
Posts: 1,166
Likes: 1,141
Liked 1,424 Times in 577 Posts
Default

Quote:
Originally Posted by GerSan69 View Post
You mentioned "a small lip at the rear of the ejector rod". I was wondering what you mean. Is there a sharp edge catching something, or ?
Please don't keep thinking that any part is "too short," "broken," or anything else. Damage in that area is almost always from abuse, so it's not something that will naturally occur. That also means it's rare.
Do you have a reputable gunsmith nearby that can advise you on this? Revolvers do have some somewhat complicated mechanisms in them, and unless you are thoroughly familiar, you can do more harm than good. As a "good Forum member," I want to see folks that come on here are able to enjoy their firearms, not get into a situation that costs them money needlessly.
I think he's referring to the center pin and has his "rear" and "front" sdrawkcab.....
Reply With Quote
The Following User Likes This Post:
  #17  
Old 04-22-2021, 01:41 AM
minconrevo minconrevo is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Feb 2008
Posts: 747
Likes: 154
Liked 568 Times in 290 Posts
Default

You have a really nice looking Mod 19 there. Could be the previous owner's gunsmith was a fair hammer mechanic but not ready to work on a precision device, like your revolver. There may be a multiplicity of problems with the revolver to deal with. I suspect several misfit parts in the mix. Rather than try to fight fixing it yourself, I'd suggest finding a competent gunsmith who regularly DOES work on S&W revolvers.
Reply With Quote
The Following 5 Users Like Post:
  #18  
Old 04-22-2021, 02:06 AM
Gunhacker's Avatar
Gunhacker Gunhacker is offline
SWCA Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Oct 2002
Location: SF East Bay - "the delta"
Posts: 3,508
Likes: 1,585
Liked 4,495 Times in 1,516 Posts
Default

Quote:
Originally Posted by SuperSapper View Post
I took the entire assembly apart and cleaned it very thoroughly. The ejector rod fully retracts easily, but when pushed back and sitting flush with the cylinder, there is a small lip at the rear of the ejector rod. It is as if the part inside the ejector rod that is pushed back when you push the cylinder release forward (to open the cylinder) is too short.

I can't imagine any reason to replace it. Do they get damaged by breaking off a part such that they are short and need to be replaced? It doesn't look damaged, even under a magnifying glass.

Since the hammer and trigger aren't original to the gun, is there any reason the rod inside would need to be replaced. I attached the pic again to show what we're talking about.

Mark
That is normal in that picture, and that is the front of the ejector rod, not the back.

You took which assembly apart??

Did you check the front locking bolt (red pointer in below pic) for free movement?

Study this pic closely, the spring loaded pin (locking bolt) that I'm pointing to, the end of that pin fits into the end of the ejector rod to lock it in place when the cylinder is closed.

The center pin in the ejector rod that you think looks short, it needs to be that way so there is room for the locking bolt (pin) to fit into the end of the ejector rod.

__________________
Conrad
SWCA #1830 SWHF #222
Reply With Quote
The Following User Likes This Post:
  #19  
Old 04-22-2021, 07:35 PM
SuperSapper SuperSapper is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Apr 2021
Location: SoCal, San diego
Posts: 16
Likes: 3
Liked 11 Times in 10 Posts
Default

Quote:
Originally Posted by Gunhacker View Post
That is normal in that picture, and that is the front of the ejector rod, not the back.

You took which assembly apart?? the entire ejector rod, cylinder, center pin and extractor

Did you check the front locking bolt (red pointer in below pic) for free movement? It resists quite a bit, but does not retract from the ejector rod far enough to release the cylinder

Study this pic closely, the spring loaded pin (locking bolt) that I'm pointing to, the end of that pin fits into the end of the ejector rod to lock it in place when the cylinder is closed.

The center pin in the ejector rod that you think looks short, it needs to be that way so there is room for the locking bolt (pin) to fit into the end of the ejector rod. Understood, but the locking bolt is not going far enough back to release the ejector rod

Yes. I checked that. The issue is that the "locking bolt" does not retract far enough to release the ejector rod when I push the thumb release. I used a very small jeweler's type screwdriver to push the locking bolt forward and at the same time pushed the thumb release to open the cylinder. When I did both of these things, it opened easily.

I got to that point because I noticed there was absolutely NOTHING holding the cylinder in once the thumb release was pushed. I noticed that it was hanging up at the rear of the ejector rod where the locking bolt inserts (right at the red arrow). What would cause the locking bolt to hang up where it meets/inserts into the ejector rod?

Oh...BTW. Maybe I have it backwards, but I use the shooter as the reference point, not the pistol; the "front" of the center pin is toward the shooter (where you load the cartridges) and "rear" is away from the shooter, toward the shroud where the locking bolt is.

How do I upload a video clip here? I'll see if I can do so

Last edited by SuperSapper; 04-22-2021 at 07:40 PM.
Reply With Quote
The Following User Likes This Post:
  #20  
Old 04-22-2021, 07:41 PM
SuperSapper SuperSapper is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Apr 2021
Location: SoCal, San diego
Posts: 16
Likes: 3
Liked 11 Times in 10 Posts
Default

Quote:
Originally Posted by minconrevo View Post
You have a really nice looking Mod 19 there. Could be the previous owner's gunsmith was a fair hammer mechanic but not ready to work on a precision device, like your revolver. There may be a multiplicity of problems with the revolver to deal with. I suspect several misfit parts in the mix. Rather than try to fight fixing it yourself, I'd suggest finding a competent gunsmith who regularly DOES work on S&W revolvers.
There do not seem to be any competent smiths here in San Diego that know enough about the older revolvers. Does anyone know someone here in San Diego?
Reply With Quote
The Following User Likes This Post:
  #21  
Old 04-22-2021, 09:37 PM
Gunhacker's Avatar
Gunhacker Gunhacker is offline
SWCA Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Oct 2002
Location: SF East Bay - "the delta"
Posts: 3,508
Likes: 1,585
Liked 4,495 Times in 1,516 Posts
Default

Quote:
Originally Posted by SuperSapper View Post
Yes. I checked that. The issue is that the "locking bolt" does not retract far enough to release the ejector rod when I push the thumb release. I used a very small jeweler's type screwdriver to push the locking bolt forward and at the same time pushed the thumb release to open the cylinder. When I did both of these things, it opened easily.

I got to that point because I noticed there was absolutely NOTHING holding the cylinder in once the thumb release was pushed. I noticed that it was hanging up at the rear of the ejector rod where the locking bolt inserts (right at the red arrow). What would cause the locking bolt to hang up where it meets/inserts into the ejector rod?

Oh...BTW. Maybe I have it backwards, but I use the shooter as the reference point, not the pistol; the "front" of the center pin is toward the shooter (where you load the cartridges) and "rear" is away from the shooter, toward the shroud where the locking bolt is.

How do I upload a video clip here? I'll see if I can do so
After you have the cylinder opened and the ejector rod out of the way, did you then try pushing on the front (correct nomenclature is the muzzle end is the front and the grip end is the rear, not shooter orientation) locking bolt to see how far it can retract? If it does not easily retract where the end of it is flush or almost flush with the end of hole it's sticking out of... then there is likely a build up of caked junk behind the pin in the hole that needs to be cleaned out to restore full movement.

To load a video, you have put it on a hosting website, like youtube and then insert the link url to it in your post.

Call these guys and ask if they inspect/repair S&W revolvers, they are in San Diego.

On their website they say: OVER 30 YEARS OF COMBINED GUNSMITHING/ARMORER EXPERIENCE FROM THE MILITARY, LAW ENFORCEMENT AND THE PRIVATE SECTOR.


San Diego Gunsmithing
__________________
Conrad
SWCA #1830 SWHF #222

Last edited by Gunhacker; 04-23-2021 at 07:03 PM.
Reply With Quote
The Following 3 Users Like Post:
  #22  
Old 04-23-2021, 08:09 AM
BigChief52 BigChief52 is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Nov 2014
Posts: 155
Likes: 1
Liked 163 Times in 58 Posts
Default

Quote:
Originally Posted by Gunhacker View Post
With the cylinder open, can you press on the front locking bolt (the pin in front of the ejector rod) with a punch or the end of a tooth brush handle, and get it to fully retract into the hole it protrudes from?

If not, or it feels like there's more than spring resistance, chances are there is a build up crud in that channel that is preventing the front bolt from retracting far enough to allow the ejector rod to unlatch.

I had that issue with a used 586 I bought, a good cleaning with an aerosol gun cleaner blasted loose a surprising amount of caked powder residue out of that bolt channel. Once cleaned, it fixed my cylinder release problem.

Don't mess with the front of the ejector rod, there needs to be a certain amount of engagement with the front locking bolt, and what you describe sounds normal.
This worked for me too. I could feel that the locking bolt was stiff when I pushed it with a leftover chop stick from Chinese take out. They always seem to come in handy. I didn't want to try drifting out that tiny pin so I dripped some oil in and kept working the bolt with the chopstick until it loosened up. Still works fine years later.
Reply With Quote
The Following 3 Users Like Post:
  #23  
Old 04-23-2021, 11:11 AM
SuperSapper SuperSapper is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Apr 2021
Location: SoCal, San diego
Posts: 16
Likes: 3
Liked 11 Times in 10 Posts
Default

I will definitely try this. It does feel a bit stiffer than I sense it should be, so I'll do that this evening.
Reply With Quote
The Following User Likes This Post:
  #24  
Old 04-26-2021, 10:20 PM
SuperSapper SuperSapper is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Apr 2021
Location: SoCal, San diego
Posts: 16
Likes: 3
Liked 11 Times in 10 Posts
Default Update

Good afternoon everyone,

I cleaned up the locking bolt as suggested. There were no specific issues with it retracting either before or after. I used a punch to push in the center pin as far as it could go from the front (to simulate pushing the thumb release). I noticed that there is still a bit of a lip differential between the center pin bottom and the edge of the ejector rod that houses it.

It's hanging up there at that tiny little edge. Is this normal?
Attached Images
File Type: jpg IMG_1196.jpg (70.6 KB, 32 views)

Last edited by SuperSapper; 04-26-2021 at 10:22 PM.
Reply With Quote
The Following User Likes This Post:
  #25  
Old 04-29-2021, 01:26 PM
BigChief52 BigChief52 is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Nov 2014
Posts: 155
Likes: 1
Liked 163 Times in 58 Posts
Default

A good armorer with wheel gun experience would know exactly how to make this adjustment but they seem to be getting rare these days. If it were me, I'd try ordering a new center pin and seeing if I could get it working that way. It may fit right away or it maybe like the hand where they come a bit long and have to be hand fitted. More guessing. At least with a new pin to work with I wouldn't mess up any original parts.
Reply With Quote
  #26  
Old 06-01-2021, 10:07 PM
SuperSapper SuperSapper is offline
Member
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Apr 2021
Location: SoCal, San diego
Posts: 16
Likes: 3
Liked 11 Times in 10 Posts
Default

Hi Everyone!

First, I want to thank everyone for the help and suggestions. A HUGE shout out to sndbggr1484 for sending me the Target hammer, target trigger and the centerpin (he also sent several other internals too -- Thanks much!!). Tomorrow will be the test fire to see if I got it back together correctly. For the record, I am liking the .500 hammer and trigger. Can't wait to try this thing out in a competition.

Just for future posterity and in case someone else ever has this issue, I'll outline the fix below:

So the first swap out was the center pin. That alone fixed the opening issue. Seems that sndbggr1484's center pin was about .05" longer than mine, and it did the job. It also solved the jerky trigger, since with the old center pin, the thumb release was far enough forward to interfere with the hammer drawing back. There was a few thousandths interference where there should be none.

The question of why it was too short is almost unanswerable, but I have two theories:

1. Wear and tear. It's a 19-3, so it's probably on the order of 60 years old. Possibly all of the opening and closing over time caused the end of the center pin (where it rubs against the locking bolt in the shroud up front) to have enough wear that it simply became too short.

2. It's a replacement. This seems incredulous, since there is no way this would have left a quality armorer's workshop, but the previous owner did send it to an "armorer" who apparently monkeyed around with it. He also replaced parts from another, older model. Others here noted that it was a "fishhook" hammer from a Model 15, which is consistent with what the previous owner said about the parts coming from a Model 15.

In any event, moral of the story:

1. If the cyliner does not open easily and the firearm is older, try a longer center pin and see if it alleviates the issue.

2. Make sure the armorer knows what (s)he's doing, especially if they're installing other used parts from another gun. They don't always fit.

3. I have NEVER disassembled a revolver prior to this, so I was worried I would be the same kind of monkey. I found a great video by a qualified armorer (linked above) and did it step by step. It really was not that hard after all. Research can be a powerful thing and Youtube is your friend.

Now I just need to find a good set of wood grips, and I'm set!

Hope everyone's Memorial Day was excellent!

Mark

Last edited by SuperSapper; 06-01-2021 at 10:13 PM.
Reply With Quote
  #27  
Old 06-02-2021, 07:54 AM
steelslaver's Avatar
steelslaver steelslaver is offline
US Veteran
19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference 19-3 cylinder open issue and hammer interference  
Join Date: Oct 2013
Location: Central Montana
Posts: 13,625
Likes: 12,742
Liked 39,093 Times in 9,967 Posts
Default

The ejector rod and center pin are actually fitted parts and their length is adjusted according to the final length when the barrel is adjusted to tighten up and have front sight at 12:00. Sometimes to do this shoulder on barrel is shorten slightly to make this happen. Under lug to extractor rod fit happens after barrel is installed and cylinder is being fitted. So, length varies from gun to gun. I have had the rod actually strike the lug body and needed to trim the whole thing. In fact the lug tooth that moves back and forth under the barrel sometimes requires some adjustment, by removing and filing the shoulder of its flat a bit to allow a bit more movement one way or the other

The guns of this era where not just assembled, but final fitted during assembly. As you have just learned even minor differences in one part can cause several problems

Last edited by steelslaver; 06-02-2021 at 07:58 AM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
New 500 - Hammer won't cock with cylinder open Killawattz S&W Revolvers: 1980 to the Present 25 08-18-2020 03:17 PM
686 SSR hammer spring interference JFrames4ever S&W-Smithing 5 01-16-2019 11:39 AM
S&W Model 10-5 Missaligned cylinder and cylinder-barrel gap issue ct241 S&W-Smithing 21 09-28-2014 07:24 PM
19-4 cylinder play when cylinder open sixpointfive S&W Revolvers: 1961 to 1980 1 06-24-2012 01:11 AM
586 Cylinder is hard to turn whether cylinder is open or closed pittspilot S&W-Smithing 4 11-26-2011 07:27 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 07:35 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)