Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Revolvers: 1980 to the Present
o

Notices

S&W Revolvers: 1980 to the Present All NON-PINNED Barrels, the L-Frames, and the New Era Revolvers


Reply
 
Thread Tools Display Modes
  #1  
Old 11-14-2010, 02:49 PM
villageidiot villageidiot is offline
Member
 
Join Date: Jan 2004
Location: ga
Posts: 36
Likes: 0
Liked 0 Times in 0 Posts
Default polishing stainless steel

What polishing cloth can anyone recommend for polishing out small
scratches and stain on a stainless revolver?
Reply With Quote
  #2  
Old 11-14-2010, 03:30 PM
DonD DonD is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Feb 2003
Location: Central TX
Posts: 2,070
Likes: 431
Liked 877 Times in 447 Posts
Default

Don't know about a polishing cloth but whatever you do, don't use steel wool or anything possibly containing any form of metal. That will just start corrosion initiation sites. Don
Reply With Quote
The Following User Likes This Post:
  #3  
Old 11-14-2010, 03:32 PM
medxam medxam is offline
US Veteran
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: May 2004
Location: Jacksonville, NC, USA
Posts: 1,108
Likes: 120
Liked 413 Times in 193 Posts
Post

Old men's undershirts!
__________________
Doc Garrett
Dead Man's Doctor
Reply With Quote
The Following User Likes This Post:
  #4  
Old 11-14-2010, 04:38 PM
TRD TRD is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Mar 2009
Location: GA.
Posts: 90
Likes: 2
Liked 7 Times in 5 Posts
Default

It really all depends on what finish you are stating with. Unless the finish is bead blasted or polished I’ve used 3-M 07448 GRAY FINE GRIT, and 07445 WHITE VERY FINE GRIT SCOTCH BRITE SCUFF PADS with great success. Deeper scratches can be easily removed with heavier grit RED or GREEN SCUFF PADS if necessary and then those scratches blended with the other pads. With a little patience and practice you will be able to match the surrounding areas perfectly. I found the gray and white scuff pads I was looking for at Grainger Industrial Supply.
Reply With Quote
The Following User Likes This Post:
  #5  
Old 11-14-2010, 06:41 PM
Big'un Big'un is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Sep 2009
Location: Ontario,Canada
Posts: 85
Likes: 0
Liked 16 Times in 8 Posts
Default

All I have ever used is Mothers Mag Polish and a soft cloth.
Attached Images
File Type: jpg Picture 012S&W.jpg (152.0 KB, 975 views)
Reply With Quote
The Following 3 Users Like Post:
  #6  
Old 11-14-2010, 07:37 PM
Bullseye Smith's Avatar
Bullseye Smith Bullseye Smith is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Nov 2004
Location: Mountain State
Posts: 3,569
Likes: 56
Liked 379 Times in 149 Posts
Default

Quote:
Originally Posted by Big'un View Post
All I have ever used is Mothers Mag Polish and a soft cloth.
I agree with the above 100%
Reply With Quote
  #7  
Old 11-14-2010, 07:43 PM
desertdweller desertdweller is offline
SWCA Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Dec 2009
Location: Arizona
Posts: 221
Likes: 6
Liked 45 Times in 18 Posts
Default My 686

I took the plunge after encouragement from several fourm members and used 2000 grit automotive sandpaper.
I used WD40 as a liquid and it turned out pretty good. The 686 was in pretty bad shape and in my opinion it turned out great.
When I got it to look the way I wanted I used some Flitz and a microfiber cloth to put the finishing touches on it.
Attached Images
File Type: jpg 764.jpg (98.2 KB, 1345 views)
Reply With Quote
The Following 4 Users Like Post:
  #8  
Old 11-14-2010, 07:55 PM
ar15ed ar15ed is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Feb 2010
Location: western north carolina
Posts: 1,068
Likes: 0
Liked 165 Times in 62 Posts
Default

it is beautiful!
Reply With Quote
  #9  
Old 11-14-2010, 08:59 PM
Black_Sheep's Avatar
Black_Sheep Black_Sheep is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Nov 2008
Location: Minnesota
Posts: 1,937
Likes: 1,516
Liked 1,068 Times in 348 Posts
Default

This Model 60 has been hand polished a couple of times with Flitz. After an extended range session today I hit it again with some stuff called EZ Reflections chrome and metal polish. The gun looks better every time I polish it, the depth and shine is very comparable to nickel...
Attached Images
File Type: jpg pol60.jpg (204.4 KB, 1202 views)
__________________
"Shall not be infringed"
Reply With Quote
The Following 2 Users Like Post:
  #10  
Old 11-14-2010, 10:14 PM
ar15ed ar15ed is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Feb 2010
Location: western north carolina
Posts: 1,068
Likes: 0
Liked 165 Times in 62 Posts
Default

man, that is beautiful, too! i have got to try this!
Reply With Quote
  #11  
Old 11-15-2010, 10:42 AM
villageidiot villageidiot is offline
Member
 
Join Date: Jan 2004
Location: ga
Posts: 36
Likes: 0
Liked 0 Times in 0 Posts
Default

Thanks to all the is what I was looking for was the Mother's and Flitz cloth!!!
Reply With Quote
  #12  
Old 11-15-2010, 07:51 PM
Black_Sheep's Avatar
Black_Sheep Black_Sheep is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Nov 2008
Location: Minnesota
Posts: 1,937
Likes: 1,516
Liked 1,068 Times in 348 Posts
Default

I use an old cotton washcloth for polishing and do the final wipe down with a microfiber cloth. I use a microfiber cloth on blued guns too...
__________________
"Shall not be infringed"
Reply With Quote
  #13  
Old 11-15-2010, 11:07 PM
Cruiser RN's Avatar
Cruiser RN Cruiser RN is offline
Member
 
Join Date: May 2008
Location: Yonkers,New York
Posts: 1,001
Likes: 13
Liked 90 Times in 46 Posts
Default

I totally agree.After a good coat the gun looks spectacular....Mike
Quote:
Originally Posted by Big'un View Post
All I have ever used is Mothers Mag Polish and a soft cloth.
Reply With Quote
  #14  
Old 12-07-2010, 05:08 PM
ar15ed ar15ed is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Feb 2010
Location: western north carolina
Posts: 1,068
Likes: 0
Liked 165 Times in 62 Posts
Default

well, i tried it, too! i got a pretty good deal on a 60-7, polished it by hand for about 6 hours with simichrome and an old t-shirt, then a couple of hours with mother's. i was looking for a set of the old ace boot grips, but haven't had any luck finding any. i got these grips for the time being.

Reply With Quote
The Following 4 Users Like Post:
  #15  
Old 12-07-2010, 09:49 PM
RIDE-RED 350r's Avatar
RIDE-RED 350r RIDE-RED 350r is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Nov 2010
Location: Blossvale NY
Posts: 1,295
Likes: 3,964
Liked 950 Times in 427 Posts
Default

Quote:
Originally Posted by Big'un View Post
All I have ever used is Mothers Mag Polish and a soft cloth.
X2! Its good stuff! I use it on the bare aluminum chassis' of my sleds, makes em shine almost like chrome. And just last weekend, i treated my new Smith to some quality time with Mothers and a cotton diaper. (clean of course! LOL!)
Reply With Quote
  #16  
Old 12-07-2010, 10:00 PM
kennyb's Avatar
kennyb kennyb is offline
SWCA Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Dec 2008
Posts: 6,895
Likes: 736
Liked 1,208 Times in 737 Posts
Default

Quote:
Originally Posted by Big'un View Post
All I have ever used is Mothers Mag Polish and a soft cloth.

another vote for mother's mag polish and an old t-shirt...u can make it as bright and finished as you want to using this method...
__________________
SWCA#2208
KK4EMO
Reply With Quote
  #17  
Old 12-08-2010, 04:06 PM
JamesArthur60's Avatar
JamesArthur60 JamesArthur60 is offline
US Veteran
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Dec 2008
Location: Columbus, OH
Posts: 1,333
Likes: 139
Liked 311 Times in 124 Posts
Default

My choices with positive results: FLITZ, MOTHER'S, and SIMICHROME Polish. If you want a mirror finish, I use 2000 grit auto repair sandpaper with dabs of Rem oil for wetness.
Reply With Quote
  #18  
Old 12-08-2010, 05:20 PM
4thUSMC 4thUSMC is offline
Member
polishing stainless steel polishing stainless steel  
Join Date: Feb 2009
Location: Texas
Posts: 24
Likes: 0
Liked 2 Times in 2 Posts
Default

As far as cloth, an old flannel shirt has always worked great for me in getting out the fine scratches.
Reply With Quote
The Following User Likes This Post:
  #19  
Old 12-08-2010, 11:26 PM
MR.G MR.G is offline
Member
polishing stainless steel  
Join Date: Jul 2001
Posts: 322
Likes: 59
Liked 109 Times in 60 Posts
Default

I use either Flitz or Mothers Mag Wheel polish with a cotton cloth.
Reply With Quote
  #20  
Old 06-17-2011, 01:55 PM
M3Stuart's Avatar
M3Stuart M3Stuart is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Mar 2011
Location: Northeast Texas
Posts: 2,861
Likes: 921
Liked 1,326 Times in 723 Posts
Default

I found this information very helpful! Thanks for the info!
__________________
But then, what do I know?
Reply With Quote
  #21  
Old 06-17-2011, 02:10 PM
Maximumbob54's Avatar
Maximumbob54 Maximumbob54 is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Oct 2010
Posts: 7,202
Likes: 9,079
Liked 1,921 Times in 1,043 Posts
Default

Mother’s touched S&W’s:





Mother’s touched Rugers:





The cylinder is the hardest to polish. The steel is hard as heck and I don’t want to round off any stop notches. But it can be done. I break out the cotton rag and Mothers on a weekend movie and keep going with these from time to time. They all get better slowly but surely.
Reply With Quote
  #22  
Old 06-17-2011, 02:50 PM
safearm's Avatar
safearm safearm is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Feb 2009
Location: Mississippi
Posts: 1,753
Likes: 232
Liked 687 Times in 252 Posts
Default

Another vote for Mother's. I polished a well used police trade-in Model 67 and it looked like it had been refinished in chrome.
Reply With Quote
  #23  
Old 06-17-2011, 02:57 PM
stang1911's Avatar
stang1911 stang1911 is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Jun 2010
Location: NEW YORK STATE
Posts: 173
Likes: 92
Liked 117 Times in 52 Posts
Wink

BIRCHWOOD CASEY LEAD REMOVER & POLISHING CLOTH WORKS GREAT. JUST KEEP IT OFF THE BLUED PARTS!
Reply With Quote
  #24  
Old 06-18-2011, 03:39 PM
carl3989's Avatar
carl3989 carl3989 is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Mar 2011
Location: Hebron,N.Y.
Posts: 398
Likes: 207
Liked 157 Times in 52 Posts
Talking Another vote for Mother's.

Quote:
Originally Posted by Big'un View Post
All I have ever used is Mothers Mag Polish and a soft cloth.
Available at every auto parts store.
Reply With Quote
  #25  
Old 06-18-2011, 05:51 PM
Sportsterguy's Avatar
Sportsterguy Sportsterguy is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Dec 2005
Location: Ask the NSA
Posts: 2,208
Likes: 111
Liked 119 Times in 73 Posts
Default

Another vote for Mothers followed by a good wax job to keep oxidation away. Took me a few episodes of "Dancing with the Stars" with Stacy Kiebler (WOW) to shine my 66-2 while the wife watched. I like it personally. Some like the original finish but I don't use this as a self defense weapon so am not worried about the shine and light reflection. You can always return it to its original look with some Scotch Bright (sp).

Let us see your's when you're done please.

Roger

__________________
V/R
Roger / SG

Last edited by Sportsterguy; 06-18-2011 at 05:57 PM.
Reply With Quote
The Following 2 Users Like Post:
  #26  
Old 06-19-2011, 08:35 AM
Smith357's Avatar
Smith357 Smith357 is offline
Moderator
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Jan 2004
Location: Columbus Ohio
Posts: 4,579
Likes: 931
Liked 3,590 Times in 816 Posts
Default

I took my 64 down to the bare frame and cylinder, then I used jewelers rouge dissolved in gun oil and rubbed it out with my bare hands. It turned my hands black but it took off the crud and gave it a nice polish. All told it took a total of about 4 nights just rubbing the revolver while watching the idiot box to get it where I wanted it. Before reassembly the buggered screws were dressed by chucking them lightly in a drill and turning them on some 400 grit paper then polishing lightly with a Dremel tool on low speed as was the thumb latch all with same standard red rouge used to polish gold.

before

after

__________________
Regards,
Guy-Harold Smith II
Reply With Quote
The Following User Likes This Post:
  #27  
Old 06-19-2011, 08:47 AM
Bullseye Smith's Avatar
Bullseye Smith Bullseye Smith is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Nov 2004
Location: Mountain State
Posts: 3,569
Likes: 56
Liked 379 Times in 149 Posts
Default

Great looking pencil there 357, I bet it writes great to .
Reply With Quote
  #28  
Old 01-13-2014, 11:17 AM
roundels's Avatar
roundels roundels is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Jun 2011
Posts: 61
Likes: 3
Liked 67 Times in 24 Posts
Default Polished M64

Ooh, that's nice. Love the diamond grips on it, too.



GLCM Test Team 1980-84
Yes Virginia, the Air Force once had Infantry!

Last edited by roundels; 01-13-2014 at 11:32 AM.
Reply With Quote
  #29  
Old 01-13-2014, 02:20 PM
MattJames MattJames is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Dec 2013
Location: Pittsburgh, PA
Posts: 347
Likes: 642
Liked 643 Times in 153 Posts
Default

I just started on a 629 yesterday. Beginning with 1,000 grit but may step down to 600 around the grip area since it seems to be scratched a tad deeper than what 1,000 can remove.
Then up to 1,000, 1,500, 2,000 and finally 2,500 (all with pb blaster for lube) before it hits the buff wheel.
Reply With Quote
  #30  
Old 01-13-2014, 02:54 PM
TAROMAN's Avatar
TAROMAN TAROMAN is offline
US Veteran
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Jan 2010
Location: The wet side of Oregon
Posts: 6,290
Likes: 8,789
Liked 7,778 Times in 2,375 Posts
Default

I have polished up a number of really beat up SS Smiths.
For jobs like these, you will need a lot more than Mother's.
I use auto body sandpaper (dry - tried it both ways) cut into 1" wide strips.
Depending on how bad it is, have started out with as coarse as 320 grit.
Different areas will probably need different grits to start. You may even need to use a fine file to smooth out deep gouges, usually the bottom of the triggerguard where the gun has been dropped.
Strip the gun, re-install the sideplate with all flathead screws. I keep a set of screws just for this purpose.
For the flat areas, I wrap the sandpaper around a little aluminum sanding black I made.
After all has been worked with the first sandpaper, go to the next finer grade. Work it with this one to smooth out all the scratches from the last grade.
Repeat this with finer and finer sandpaper until you end up with 2000 grit.
You will quickly learn that if you don't completely remove the previous scratches before going finer that you will have to back up and do it over, Trust me on this!
After its polished to 2000 all over, start in with Mother's and rub, rub, rub. I start out polishing with a cotton shop rag and end up with a microfiber cloth.

Here are some of the worst that I have done:

This model 67 was a complete junker. $150 at the LGS. Dirtiest and most beat one I ever saw. Soaked 3 days in Ed's red before even starting on it:


This one had a very coarse sandblast finish with lots of pitting (yes, stainless DOES rust!) like it had been a boat gun. It took more work than the others:


This was another well-used gun dinged all over and rusted in a couple spots:


And one that looked as if it had been dragged behind a truck:

Final note: Unless you REALLY know what you're doing, do not use any power tools!
__________________
-jwk-
US Army '72-'95

Last edited by TAROMAN; 03-18-2017 at 09:39 PM.
Reply With Quote
The Following 9 Users Like Post:
  #31  
Old 01-13-2014, 03:53 PM
408essj's Avatar
408essj 408essj is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Sep 2013
Posts: 20
Likes: 0
Liked 17 Times in 4 Posts
Default

How bout the laser etching? Will the mothers polish off the "engraving"
Reply With Quote
  #32  
Old 01-13-2014, 04:59 PM
TAROMAN's Avatar
TAROMAN TAROMAN is offline
US Veteran
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Jan 2010
Location: The wet side of Oregon
Posts: 6,290
Likes: 8,789
Liked 7,778 Times in 2,375 Posts
Default

Quote:
Originally Posted by 408essj View Post
How bout the laser etching? Will the mothers polish off the "engraving"
Mother's alone isn't aggressive enough to erase laser etching.
__________________
-jwk-
US Army '72-'95
Reply With Quote
  #33  
Old 01-13-2014, 06:21 PM
75Vette's Avatar
75Vette 75Vette is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Jul 2013
Location: South of Atl
Posts: 4,062
Likes: 38,572
Liked 14,464 Times in 3,107 Posts
Default

Actually, Mother's will all but remove laser etching. I used it by hand to polish my 629-3 6 1/2" Classic and before I realized what I'd done, the etchings on both sides of the barrel had just about disappeared. About made me sick. If I had it to do again, I'd stayed away from those areas.
Reply With Quote
The Following User Likes This Post:
  #34  
Old 01-13-2014, 07:16 PM
MattJames MattJames is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Dec 2013
Location: Pittsburgh, PA
Posts: 347
Likes: 642
Liked 643 Times in 153 Posts
Default

TAROMAN: Nice write-up and photos. That's an amazing effort to the work that you did to pull that finish.
Reply With Quote
  #35  
Old 10-23-2015, 07:08 AM
tramblygoat tramblygoat is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Mar 2015
Location: Burgundy France
Posts: 45
Likes: 21
Liked 46 Times in 19 Posts
Default

There seems to be some doubt about polishing and etchings or engravings. I have just bought a 629 Classic. Along the barrel there is one side the 'Smith and Wesson 44 Magnum' and on the other the '629 Classic' and then of course like all S&W there is their logo and stuff on the side plate.
So for those experienced out there. Did you go gentler on these areas or does just using 'Mothers' alone with a soft cloth leave these engravings intact?
I want to ask before getting down to the business of polishing up mine. I'll also be doing a 617 if the 629 goes well.
Reply With Quote
  #36  
Old 10-23-2015, 12:09 PM
75Vette's Avatar
75Vette 75Vette is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Jul 2013
Location: South of Atl
Posts: 4,062
Likes: 38,572
Liked 14,464 Times in 3,107 Posts
Default

I'd recommend staying away from the etching all together. It doesn't take much rubbing to make it start fading.
__________________
Don't You Ever Wash That Thing
Reply With Quote
The Following User Likes This Post:
  #37  
Old 10-23-2015, 12:17 PM
BigBill BigBill is offline
Absent Comrade
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Jan 2011
Location: Planet earth
Posts: 13,869
Likes: 2,079
Liked 13,353 Times in 5,549 Posts
Default

Simi-Chrome polish with a tee shirt soft rag. Lots of elbow grease. We remove machining marks in injection die molds with it.

Save the used Simi-Chrome polish to polish the blued guns lightly.
It cleans up nickel finishes too.
Reply With Quote
  #38  
Old 10-23-2015, 01:45 PM
Old cop Old cop is offline
US Veteran
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Oct 2010
Posts: 7,783
Likes: 4,206
Liked 15,132 Times in 4,142 Posts
Default

I have a satin nickel 442 from the early '90s that looks like new, but I can't get the high gloss look I'd like. The only thing I've used is Mother's and the gun looks great, but still has the satin finish. Any ideas?
__________________
Old Cop
LEO (Ret.)
Reply With Quote
  #39  
Old 10-23-2015, 02:07 PM
Nevada Ed's Avatar
Nevada Ed Nevada Ed is online now
US Veteran
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Nov 2012
Location: Reno Nv
Posts: 13,376
Likes: 3,183
Liked 12,712 Times in 5,669 Posts
Default

I have used Flitz on my 686 and m49's .......... but
I do not get carried away with it.

I did not know about Mothers......
I will have to try that out to see how well it works. It is always
nice to have a backup.

Hoppe's #9 will work but lots of time and elbow grease is needed and a brass brush is also helpful.
Reply With Quote
  #40  
Old 10-23-2015, 02:10 PM
S&W Rover's Avatar
S&W Rover S&W Rover is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Apr 2007
Location: USA
Posts: 1,342
Likes: 1,255
Liked 1,134 Times in 521 Posts
Default

Quote:
Originally Posted by TRD View Post
It really all depends on what finish you are stating with. Unless the finish is bead blasted or polished I’ve used 3-M 07448 GRAY FINE GRIT, and 07445 WHITE VERY FINE GRIT SCOTCH BRITE SCUFF PADS with great success. Deeper scratches can be easily removed with heavier grit RED or GREEN SCUFF PADS if necessary and then those scratches blended with the other pads. With a little patience and practice you will be able to match the surrounding areas perfectly. I found the gray and white scuff pads I was looking for at Grainger Industrial Supply.
For stainless guns -- The gray and white Scotchbrite® pads are available at NAPA stores -- they are apparently used when priming and painting cars. Not expensive.

But caution -- don't use the green pads found in grocery stores, Wal-Mart, etc. Far too coarse.

I've used Flitz (in a tube) with good results after using the Scotchbrite® pads -- but you have to be careful about how much you use it, or you will soon have a very shiny (mirror-like) surface that is not really like the original S&W "tumbled" stainless look.
__________________
S&W Rover

Last edited by S&W Rover; 10-23-2015 at 10:15 PM.
Reply With Quote
  #41  
Old 10-23-2015, 03:42 PM
Officerblue's Avatar
Officerblue Officerblue is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Mar 2015
Location: Arizona
Posts: 150
Likes: 259
Liked 121 Times in 47 Posts
Default

wow I think we will refer to you as Master Yoda now! All those guns are beautiful works of art...
Reply With Quote
  #42  
Old 10-23-2015, 06:30 PM
Black_Sheep's Avatar
Black_Sheep Black_Sheep is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Nov 2008
Location: Minnesota
Posts: 1,937
Likes: 1,516
Liked 1,068 Times in 348 Posts
Default

Quote:
Originally Posted by Old cop View Post
I have a satin nickel 442 from the early '90s that looks like new, but I can't get the high gloss look I'd like. The only thing I've used is Mother's and the gun looks great, but still has the satin finish. Any ideas?
The satin nickel coating requires different preparation and application processes than a bright nickel finish. I don't believe it's possible to polish a satin nickel firearm to a bright nickel appearance.
__________________
"Shall not be infringed"
Reply With Quote
  #43  
Old 10-24-2015, 12:49 AM
SeamasterSig SeamasterSig is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Feb 2015
Location: Southwest Florida
Posts: 494
Likes: 1,457
Liked 534 Times in 236 Posts
Default

Quote:
Originally Posted by Big'un View Post
All I have ever used is Mothers Mag Polish and a soft cloth.
+1 Mothers produces fast results without much effort if the finish is in decent condition, so go easy on it unless really you want a mirror polish.

Last edited by SeamasterSig; 10-24-2015 at 12:52 AM.
Reply With Quote
  #44  
Old 12-18-2017, 11:54 AM
999rvlvrfan 999rvlvrfan is offline
Member
polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel polishing stainless steel  
Join Date: Sep 2017
Location: Chicagoland
Posts: 23
Likes: 2
Liked 11 Times in 7 Posts
Default

I am a big fan of microfiber cloths - awesome for polishing. Great pic!
__________________
586-7, 629-6, 19-3 Ni, 36
Reply With Quote
Reply

Tags
686, model 60

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Polishing brushed stainless steel cwd500 The Lounge 5 01-08-2016 05:01 PM
Polishing stainless steel? 2ndAmendmentNut The Lounge 14 08-24-2014 01:26 PM
Steel Wool For Polishing CGhelofxr S&W-Smithing 12 09-18-2012 11:24 AM
polishing stainless steel with a dremel tool? bassoneer S&W-Smithing 11 11-23-2010 11:07 PM
Polishing an all-steel 3rd Gen TSW? ShrinkMD Smith & Wesson Semi-Auto Pistols 26 11-18-2008 02:47 PM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 10:20 PM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)