Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Revolvers: 1980 to the Present
o

Notices

S&W Revolvers: 1980 to the Present All NON-PINNED Barrels, the L-Frames, and the New Era Revolvers


Reply
 
Thread Tools Display Modes
  #1  
Old 04-11-2012, 02:45 PM
JBradford JBradford is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Mar 2012
Location: Broken Arrow OK
Posts: 18
Likes: 0
Liked 1 Time in 1 Post
Default S&W 642 trigger job

A few weeks ago I bought I new 642 double action .38sp. It's got a real stiff trigger on it, had it measured with a cheap(er) quality gauge and it was off the charts. The gauge out went to 12 lbs, so a friend of mine is guessing its around 15 lbs.

I thought it would loosen up after a few hundreds rounds. Well I've put almost 500 thru it and it's still stiff as can be. This will be my main ccl weapon but with the trigger so stiff I'm not currently carrying it.

So I'd like to do a trigger job on it. I've watched videos online, and it seems relatively easy, but I've never done any smithing only shooting. I am however a mechanical engineer by trade and I feel like a handy guy, but I've never messed with guns. What is a trigger kit you'd recommend? And would you recommend attempting this myself or paying to have it done?
Reply With Quote
  #2  
Old 04-11-2012, 03:15 PM
Ashlander's Avatar
Ashlander Ashlander is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Sep 2011
Location: Ellisville, Missouri
Posts: 2,226
Likes: 4,996
Liked 1,309 Times in 685 Posts
Default

The 640 and 642 triggers often break at about 12 or 13, so it's not unusual for shooters unused to these snubbies to find the heavier trigger pull extreme. Still, if the trigger is smooth, the pull weight is almost secondary. Before thinking trigger job, just open her up and clean it out. Check for burrs or metal filings. Lightly polish contact points. Some dry lube may be helpful -- just a bit. It might feel a lot better.
Reply With Quote
The Following User Likes This Post:
  #3  
Old 04-11-2012, 03:19 PM
OKFC05 OKFC05 is offline
Member
S&W 642 trigger job S&W 642 trigger job  
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,158
Likes: 3,604
Liked 5,199 Times in 2,172 Posts
Default

Quote:
This will be my main ccl weapon
Then caution is in order to keep from getting a light pull, and misfires from light strikes. Beware of some spring kits in the J frames for carry.
__________________
Science plus Art
Reply With Quote
  #4  
Old 04-11-2012, 04:56 PM
ultratec00 ultratec00 is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Jul 2011
Posts: 726
Likes: 0
Liked 318 Times in 216 Posts
Default

I picked up two 642s over the last couple years, gave one to my dad. Local gun shop had a sale. With the rebate, I think both were under $300/ea. They had heavy pulls, as expected. I simply went to a slightly weaker spring, cleaned them up, and did a little polishing with a dremel tool They smoothed right up. The thing about S&W revolvers, the more you work them the smoother they get. As mentioned, you don't want a spring that's too light and definitely get one from a known manufacturer: Wilson combat, etc. You can buy a Wilson Combat spring kit for a J frame for around $10, which has different weights to try.
Reply With Quote
  #5  
Old 04-11-2012, 05:27 PM
diamonback68's Avatar
diamonback68 diamonback68 is offline
US Veteran
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Jun 2003
Location: Due south of Orlando
Posts: 7,202
Likes: 597
Liked 3,451 Times in 1,412 Posts
Default

The law of physics dictates that you can never achieve the same lightness of a K, L, or N frame.
__________________
Dick
Reply With Quote
  #6  
Old 04-11-2012, 06:01 PM
icemn icemn is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Oct 2010
Posts: 499
Likes: 124
Liked 101 Times in 81 Posts
Default

You might want to google 638 trigger job ( yoda g mod ).
Reply With Quote
  #7  
Old 04-11-2012, 08:02 PM
Edmo's Avatar
Edmo Edmo is offline
US Veteran
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Jul 2009
Location: Central Arkansas
Posts: 1,200
Likes: 1,349
Liked 1,693 Times in 530 Posts
Default

Quote:
Originally Posted by icemn View Post
You might want to google 638 trigger job ( yoda g mod ).
Here is the link you speak of... Another Nutnfancy video.

S&W Airweight Trigger Job: "The Yoda G Mod" - YouTube

Edmo
__________________
TRUTH: Don't delete my posts!
Reply With Quote
  #8  
Old 04-11-2012, 08:31 PM
GaryS's Avatar
GaryS GaryS is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Nov 2009
Location: Republic of Texas
Posts: 11,344
Likes: 9,368
Liked 17,263 Times in 6,632 Posts
Default

If you search around the forum, you'll find a number of threads on this topic. The J frames, and it seems the hammerless ones in particular, have stiff triggers.

I bought a Wolff Springs rebound spring and main spring kit. I think the stock rebound spring is 18 pounds, and I used the 13 pound one. The stock mainspring is 8 1/2 pounds and the replacement is 8 pounds.

I'm by no means an expert, but I found the work pretty easy. Brownells has a video showing how to do it. Although they show a nice rebound spring tool, after reading around, I found out you don't need one.

Buy a decent set of screwdrivers because you absolutely want the screw driver to fit the screw precisely. It seems, again from reading, that it's very common for people to bung up the screws and the finish on their pistols by using craptastic screw drivers.

My gun is a 442, but all of the J frames are the same. I found that mine was totally dry inside, so in addition to the springs I oiled it.

I also found that by putting the gun inside a large ziploc bag I was able to do the work and not lose any parts. Small parts and springs mean that parts will fly around the room if you don't take steps to contain them.

After replacing the springs and oiling the internals, I found the trigger pull much better.

Before you do anything, search around the forums. There is a wealth of S&W expertise here and I've found the members more than willing to help.
Reply With Quote
  #9  
Old 04-11-2012, 08:49 PM
diamonback68's Avatar
diamonback68 diamonback68 is offline
US Veteran
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Jun 2003
Location: Due south of Orlando
Posts: 7,202
Likes: 597
Liked 3,451 Times in 1,412 Posts
Default

Quote:
Originally Posted by Edmo View Post
Here is the link you speak of... Another Nutnfancy video.

S&W Airweight Trigger Job: "The Yoda G Mod" - YouTube

Edmo

Not bad, but there's a lot of things he does in that video that you really have to be careful or you could do some serious damage to your gun. Remember he's an experienced gunsmith and knows what he's doing. He doesn't explain too clearly what, were and how the small parts surfaces are that he's honing. Doesn't explain what grit of Arkansas stone etc. I know what he's doing and I can also do it, but I'm just saying, unless you have done this a few times and have gained experience, be careful, it's not for amatuers! Most guys just do the spring kit change.
__________________
Dick

Last edited by diamonback68; 04-11-2012 at 08:52 PM.
Reply With Quote
  #10  
Old 04-11-2012, 09:50 PM
ladder13 ladder13 is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Jul 2005
Location: NC
Posts: 30,689
Likes: 57,536
Liked 52,812 Times in 16,465 Posts
Default

The Centennial models, ie 442, 642 are not hammerless, the hammer is fully enclosed inside the frame.

__________________
GOA/SAF
Reply With Quote
  #11  
Old 04-11-2012, 09:55 PM
GaryS's Avatar
GaryS GaryS is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Nov 2009
Location: Republic of Texas
Posts: 11,344
Likes: 9,368
Liked 17,263 Times in 6,632 Posts
Default

Watching the video, I was thinking the same thing. He's obviously done that thousands of times, but most of us haven't.

I heard him say that you are polishing, not removing metal, but he didn't talk about the risk of over polishing and removing the hardened metal.

When I did my 442, I did the springs and some lubrication, but that was it. It helped a lot with the trigger pull and I was happy.


Quote:
Originally Posted by diamonback68 View Post
Not bad, but there's a lot of things he does in that video that you really have to be careful or you could do some serious damage to your gun. Remember he's an experienced gunsmith and knows what he's doing. He doesn't explain too clearly what, were and how the small parts surfaces are that he's honing. Doesn't explain what grit of Arkansas stone etc. I know what he's doing and I can also do it, but I'm just saying, unless you have done this a few times and have gained experience, be careful, it's not for amatuers! Most guys just do the spring kit change.
Reply With Quote
  #12  
Old 04-11-2012, 10:11 PM
diamonback68's Avatar
diamonback68 diamonback68 is offline
US Veteran
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Jun 2003
Location: Due south of Orlando
Posts: 7,202
Likes: 597
Liked 3,451 Times in 1,412 Posts
Default

Quote:
Originally Posted by GaryS View Post
Watching the video, I was thinking the same thing. He's obviously done that thousands of times, but most of us haven't.

I heard him say that you are polishing, not removing metal, but he didn't talk about the risk of over polishing and removing the hardened metal.

When I did my 442, I did the springs and some lubrication, but that was it. It helped a lot with the trigger pull and I was happy.
Exactly my point. I highly suspect, actually I more than suspect, that when you send your gun to the factory for a standard trigger job you aren't getting all that extra honing and polishing you see in that video. They do polish the rebound slide and hone the trigger/hammer sear surfaces somewhat though. The rest is done in the springs area. Probably a 1000-1200 cycles of dry firing will accomplish the same thing.
__________________
Dick
Reply With Quote
  #13  
Old 04-11-2012, 10:25 PM
JBradford JBradford is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Mar 2012
Location: Broken Arrow OK
Posts: 18
Likes: 0
Liked 1 Time in 1 Post
Default

Thanks for the input guys. Ill keep all this in mind and for this time pay a gunsmith for his knowledge if I decide to proceed.
Reply With Quote
The Following User Likes This Post:
  #14  
Old 04-11-2012, 10:33 PM
Ironhand Ironhand is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Feb 2011
Posts: 550
Likes: 5
Liked 75 Times in 50 Posts
Default

My 49 is really heavy, heavier by far than my S-series Highway Patrolman, but I'm going to shoot it until it smooths out. Lots of dry-fire drills should help. Keep in mind that mine had set in a desk drawer or glovebox until I bought it and de-gunked the action.
Reply With Quote
  #15  
Old 04-11-2012, 11:43 PM
f2 f2 is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Feb 2006
Location: USA
Posts: 223
Likes: 11
Liked 18 Times in 13 Posts
Default

Quote:
Originally Posted by JBradford View Post
So I'd like to do a trigger job on it...
just be aware that a trigger job will not make you a better shooter, nor make you more accurate, nor give you trigger control. all of that comes with practice and technique.

try these grips and this grip technique.

Hogue Bantam Grips with Top Finger Groove S&W J-Frame Round butt

PRO TIPS with JERRY MICULEK, shootingusa.com/, sixth panel down - j-frame grip

the hogue bantams will absorb most of the kick while jerry's technique will allow you to better learn trigger control with the j-frame's DA.
Reply With Quote
  #16  
Old 04-12-2012, 05:08 AM
ogilvyspecial's Avatar
ogilvyspecial ogilvyspecial is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Jun 2010
Location: Michigan
Posts: 9,656
Likes: 1,362
Liked 1,371 Times in 699 Posts
Default

There are two references that will allow most anybody to do "passble work" on S&W Revolvers. This opinion is based on personal experience.

I have both of the Jerry Miculek DVD's but the only one anybody really needs is "Trigger Job."

The other reference that I find the most helpful is the book, "The S&W Revolver....A Shop Manual" by Jerry Kuhnhausen.

I have quite a few other references but the two mentioned above pretty much covers what most of us "shade tree" gunsmiths should be trying to do on our own. Actually they go far beyond that level so they will also give you an idea of what the next learning steps would be.

Having done 9 "Trigger Jobs", 8 on J Frames, my personal preference when it comes to spring kits is Wolff, with Wilson my 2nd choice. I purchased over $100 in Apex Kits and after trying them have pulled them from the guns they were installed in.

The reason I prefer Wolff over Wilson is that I have yet to experience 1 light primer strike with the Wolff reduced weight mainsprings, but have had 3 with the Wilson on two different guns.

To be fair to Wilson, this could have been due to idiosyncrasies in those specific actions so it could have been the luck of the draw. Since reliabilty is paramount I didn't even bother trying the reduced weight Wolff mainsprings in those 2 guns, I went right back to stock weight mainsprings, although I did use Wolff over S&W springs.

Based on my trigger pull gauge the Wolff 8.5 lb. mainspring (stock weight) gives me a lighter pull weight than a new, S&W factory 8.5 lb. mainspring. Why that is I have no idea but know that I have yet to have a light primer strike with any of the Wolff springs used, even with CCI primers, so I am very confident that any fail to fire issue would be ammo, not gun, related in any gun that has a Wolff 8.5 lb. mainspring.
__________________
Ogy
Reply With Quote
  #17  
Old 04-12-2012, 06:41 AM
Martya's Avatar
Martya Martya is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Dec 2010
Location: NW PA
Posts: 897
Likes: 343
Liked 446 Times in 240 Posts
Default

Info on my Wolff spring replacement, with some video links-

Best weight for rebound spring for a J

Then scroll down a couple of posts to see my range test results.
__________________
Marty 4513TSW 13-1 642 60-10

Last edited by Martya; 04-12-2012 at 06:44 AM.
Reply With Quote
  #18  
Old 04-12-2012, 08:05 AM
Stainz's Avatar
Stainz Stainz is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Sep 2002
Location: Pinson, AL
Posts: 2,106
Likes: 57
Liked 656 Times in 307 Posts
Default

I guess I'm from a different school of thought here. My CCW's - and home defenders - are not resprung nor do they have their triggers polished. I do deep clean them pre and post break-in - and break them in, either by dry-firing or shooting them, or some combination, to about 1,000 rounds equivalent. This preserves the stronger hammer spring's ability to pop any & all primers - and I can say, in court, if need be, that my CCW's aren't altered. They aren't plinkers! This started with my 296, then my 2" 10 & 642, and, finally, my 4" 64. The 642 is quite serviceable - but the K & L frames are even better (As said, better geometry!). Learn to adapt to your revolver - it's far more reliable that way.

Stainz
Reply With Quote
  #19  
Old 04-12-2012, 01:27 PM
Edmo's Avatar
Edmo Edmo is offline
US Veteran
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Jul 2009
Location: Central Arkansas
Posts: 1,200
Likes: 1,349
Liked 1,693 Times in 530 Posts
Default

The Wilson "Custom-Tune Spring Kit, S&W J Frame 321" I put in my new 642-1 "post lock" made the trigger pull a smidge lighter. However, it was just what this little gun needed.

After hundreds of rounds of various makes and different handload primers (CCI) I feel confident in it making any cartridge go "bang".

Edmo
__________________
TRUTH: Don't delete my posts!
Reply With Quote
  #20  
Old 04-12-2012, 01:58 PM
JBradford JBradford is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Mar 2012
Location: Broken Arrow OK
Posts: 18
Likes: 0
Liked 1 Time in 1 Post
Default

Quote:
Originally Posted by f2 View Post
just be aware that a trigger job will not make you a better shooter, nor make you more accurate, nor give you trigger control. all of that comes with practice and technique.

try these grips and this grip technique.

Hogue Bantam Grips with Top Finger Groove S&W J-Frame Round butt

PRO TIPS with JERRY MICULEK, shootingusa.com/, sixth panel down - j-frame grip

the hogue bantams will absorb most of the kick while jerry's technique will allow you to better learn trigger control with the j-frame's DA.
I completely understand that. I practice all the time and im not wanting this done with those expectations. I just want a softer trigger pull cause this seems abnormally high, even thou after research I know now it's not.
Reply With Quote
  #21  
Old 04-12-2012, 03:49 PM
one eye joe's Avatar
one eye joe one eye joe is offline
US Veteran
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Dec 2008
Location: New England
Posts: 4,190
Likes: 3,543
Liked 3,996 Times in 1,627 Posts
Default

Quote:
Originally Posted by diamonback68 View Post
Not bad, but there's a lot of things he does in that video that you really have to be careful or you could do some serious damage to your gun. Remember he's an experienced gunsmith and knows what he's doing. He doesn't explain too clearly what, were and how the small parts surfaces are that he's honing. Doesn't explain what grit of Arkansas stone etc. I know what he's doing and I can also do it, but I'm just saying, unless you have done this a few times and have gained experience, be careful, it's not for amatuers! Most guys just do the spring kit change.
Diamondback, I agree. This video lacks MUCH info that the novice would-be gunsmith needs to know. Even SIMPLE things like taking off the sideplate W/O damaging it are not mentioned. I think that there must be better instructional videos than this available....
__________________
'Nam 1968-69.DAV,VFW,NRA Inst.
Reply With Quote
  #22  
Old 04-12-2012, 04:54 PM
andyo5's Avatar
andyo5 andyo5 is offline
Member
S&W 642 trigger job  
Join Date: Aug 2007
Location: Oro Valley, Arizona
Posts: 2,370
Likes: 497
Liked 943 Times in 518 Posts
Default

I have a 642. So far, I have installed a Wolff 8 lb mainspring and 14 lb rebound spring. I have both 13 and 12 lb rebound springs on order, as it is still a bit too stiff for my liking.
If you go this route, be sure to grind the ends of the rebound spring flat, as is the factory rebound spring. Otherwise, it is difficult to install even with a dedicated gunsmithing tool. Grinding is easy with a common drill and grinding stone attachment.
Reply With Quote
  #23  
Old 04-12-2012, 05:00 PM
ogilvyspecial's Avatar
ogilvyspecial ogilvyspecial is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Jun 2010
Location: Michigan
Posts: 9,656
Likes: 1,362
Liked 1,371 Times in 699 Posts
Default

Quote:
Originally Posted by andyo5 View Post
I have a 642. So far, I have installed a Wolff 8 lb mainspring and 14 lb rebound spring. I have both 13 and 12 lb rebound springs on order, as it is still a bit too stiff for my liking.
If you go this route, be sure to grind the ends of the rebound spring flat, as is the factory rebound spring. Otherwise, it is difficult to install even with a dedicated gunsmithing tool. Grinding is easy with a common drill and grinding stone attachment.
I would advise others to be very careful with any power tools and abrasives.

You can get a nice smooth rebound slide, bottom end edges included,
with a fine polishing stone, in just a few minutes.
__________________
Ogy
Reply With Quote
  #24  
Old 04-12-2012, 05:11 PM
andyo5's Avatar
andyo5 andyo5 is offline
Member
S&W 642 trigger job  
Join Date: Aug 2007
Location: Oro Valley, Arizona
Posts: 2,370
Likes: 497
Liked 943 Times in 518 Posts
Default

Quote:
Originally Posted by ogilvyspecial View Post
I would advise others to be very careful with any power tools and abrasives.

You can get a nice smooth rebound slide, bottom end edges included,
with a fine polishing stone, in just a few minutes.
I recommended grinding the ends of the Wolff spring, not the slide.
Reply With Quote
  #25  
Old 04-12-2012, 05:34 PM
ogilvyspecial's Avatar
ogilvyspecial ogilvyspecial is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Jun 2010
Location: Michigan
Posts: 9,656
Likes: 1,362
Liked 1,371 Times in 699 Posts
Default

Quote:
Originally Posted by andyo5 View Post
I recommended grinding the ends of the Wolff spring, not the slide.
Sorry about that!

I never heard of that being recommended before so my mind must have reverted to what's "normally" done.

With that said, I usually put my springs in a vibrator / tumbler for a while with corn cob media to polish them up a little.
__________________
Ogy
Reply With Quote
  #26  
Old 04-12-2012, 06:13 PM
andyo5's Avatar
andyo5 andyo5 is offline
Member
S&W 642 trigger job  
Join Date: Aug 2007
Location: Oro Valley, Arizona
Posts: 2,370
Likes: 497
Liked 943 Times in 518 Posts
Default

Quote:
Originally Posted by ogilvyspecial View Post
Sorry about that!

I never heard of that being recommended before so my mind must have reverted to what's "normally" done.

With that said, I usually put my springs in a vibrator / tumbler for a while with corn cob media to polish them up a little.
The factory rebound spring has the ends ground flat, while the Wolff springs do not. It isn't *too bad* trying to install the Wolff 14 lb rebound spring, but for lesser weights the length is greater (more preload) and they are difficult to compress without them bending and going 'boinnngggg' across the room. Grinding the edges flat makes them alot easier to compress and install. That's probably why the factory does it.
Reply With Quote
The Following User Likes This Post:
  #27  
Old 04-12-2012, 06:50 PM
icemn icemn is offline
Member
S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job S&W 642 trigger job  
Join Date: Oct 2010
Posts: 499
Likes: 124
Liked 101 Times in 81 Posts
Default

As has been the case on this forum on this issue in the past, there have been alot of different thoughts expressed and that's good. The individual can then decide for themselve's what they want to do. This forum is a great resource. There is alot of tremendous information here and some great people who are willing to share their extensive knowledge and experience.

(for what its worth, I used an ultra fine arkansas stone on my 2 j- frames and have subsequently put several hundred rounds down range in each with no issues )
Reply With Quote
Reply

Tags
442, 638, 640, 642, airweight, brownells, cartridge, ccw, centennial, gunsmith, hammerless, highway patrolman, hogue, j frame, lock, patrolman, primer, round butt, s&w, sideplate, smith & wesson, smith and wesson, smith-wessonforum.com

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
What trigger pull weight are you getting on your APEX Flat Faced FSS Trigger install? falconman515 Smith & Wesson M&P Pistols 42 12-17-2021 11:20 PM
Trigger pull gauge & Browning A-Bolt trigger spring Devil_bri WANTED to Buy 0 01-20-2017 11:01 AM
M&P9 Pro Series CORE Trigger Components For Sale - Trigger, Springs, Sear, RAM, Etc. falconman515 Accessories/Misc - For Sale or Trade 3 09-09-2016 06:45 PM
Sold: nice k-football cutout grip, K SA .500 Target hammer/trigger, true SS trigger Jeroenw114 Accessories/Misc - For Sale or Trade 3 10-19-2013 11:54 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 08:07 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)