|
|
04-11-2012, 02:45 PM
|
Member
|
|
|
Join Date: Mar 2012
Location: Broken Arrow OK
Posts: 18
Likes: 0
Liked 1 Time in 1 Post
|
|
S&W 642 trigger job
A few weeks ago I bought I new 642 double action .38sp. It's got a real stiff trigger on it, had it measured with a cheap(er) quality gauge and it was off the charts. The gauge out went to 12 lbs, so a friend of mine is guessing its around 15 lbs.
I thought it would loosen up after a few hundreds rounds. Well I've put almost 500 thru it and it's still stiff as can be. This will be my main ccl weapon but with the trigger so stiff I'm not currently carrying it.
So I'd like to do a trigger job on it. I've watched videos online, and it seems relatively easy, but I've never done any smithing only shooting. I am however a mechanical engineer by trade and I feel like a handy guy, but I've never messed with guns. What is a trigger kit you'd recommend? And would you recommend attempting this myself or paying to have it done?
|
04-11-2012, 03:15 PM
|
|
Member
|
|
|
Join Date: Sep 2011
Location: Ellisville, Missouri
Posts: 2,226
Likes: 4,996
Liked 1,309 Times in 685 Posts
|
|
The 640 and 642 triggers often break at about 12 or 13, so it's not unusual for shooters unused to these snubbies to find the heavier trigger pull extreme. Still, if the trigger is smooth, the pull weight is almost secondary. Before thinking trigger job, just open her up and clean it out. Check for burrs or metal filings. Lightly polish contact points. Some dry lube may be helpful -- just a bit. It might feel a lot better.
|
The Following User Likes This Post:
|
|
04-11-2012, 03:19 PM
|
Member
|
|
|
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,158
Likes: 3,605
Liked 5,199 Times in 2,172 Posts
|
|
Quote:
This will be my main ccl weapon
|
Then caution is in order to keep from getting a light pull, and misfires from light strikes. Beware of some spring kits in the J frames for carry.
__________________
Science plus Art
|
04-11-2012, 04:56 PM
|
Member
|
|
|
Join Date: Jul 2011
Posts: 726
Likes: 0
Liked 318 Times in 216 Posts
|
|
I picked up two 642s over the last couple years, gave one to my dad. Local gun shop had a sale. With the rebate, I think both were under $300/ea. They had heavy pulls, as expected. I simply went to a slightly weaker spring, cleaned them up, and did a little polishing with a dremel tool They smoothed right up. The thing about S&W revolvers, the more you work them the smoother they get. As mentioned, you don't want a spring that's too light and definitely get one from a known manufacturer: Wilson combat, etc. You can buy a Wilson Combat spring kit for a J frame for around $10, which has different weights to try.
|
04-11-2012, 05:27 PM
|
|
US Veteran
|
|
|
Join Date: Jun 2003
Location: Due south of Orlando
Posts: 7,202
Likes: 597
Liked 3,451 Times in 1,412 Posts
|
|
The law of physics dictates that you can never achieve the same lightness of a K, L, or N frame.
__________________
Dick
|
04-11-2012, 06:01 PM
|
Member
|
|
|
Join Date: Oct 2010
Posts: 499
Likes: 124
Liked 101 Times in 81 Posts
|
|
You might want to google 638 trigger job ( yoda g mod ).
|
04-11-2012, 08:02 PM
|
|
US Veteran
|
|
|
Join Date: Jul 2009
Location: Central Arkansas
Posts: 1,200
Likes: 1,349
Liked 1,693 Times in 530 Posts
|
|
Quote:
Originally Posted by icemn
You might want to google 638 trigger job ( yoda g mod ).
|
Here is the link you speak of... Another Nutnfancy video.
S&W Airweight Trigger Job: "The Yoda G Mod" - YouTube
Edmo
__________________
TRUTH: Don't delete my posts!
|
04-11-2012, 08:31 PM
|
|
Member
|
|
|
Join Date: Nov 2009
Location: Republic of Texas
Posts: 11,345
Likes: 9,368
Liked 17,264 Times in 6,633 Posts
|
|
If you search around the forum, you'll find a number of threads on this topic. The J frames, and it seems the hammerless ones in particular, have stiff triggers.
I bought a Wolff Springs rebound spring and main spring kit. I think the stock rebound spring is 18 pounds, and I used the 13 pound one. The stock mainspring is 8 1/2 pounds and the replacement is 8 pounds.
I'm by no means an expert, but I found the work pretty easy. Brownells has a video showing how to do it. Although they show a nice rebound spring tool, after reading around, I found out you don't need one.
Buy a decent set of screwdrivers because you absolutely want the screw driver to fit the screw precisely. It seems, again from reading, that it's very common for people to bung up the screws and the finish on their pistols by using craptastic screw drivers.
My gun is a 442, but all of the J frames are the same. I found that mine was totally dry inside, so in addition to the springs I oiled it.
I also found that by putting the gun inside a large ziploc bag I was able to do the work and not lose any parts. Small parts and springs mean that parts will fly around the room if you don't take steps to contain them.
After replacing the springs and oiling the internals, I found the trigger pull much better.
Before you do anything, search around the forums. There is a wealth of S&W expertise here and I've found the members more than willing to help.
|
04-11-2012, 08:49 PM
|
|
US Veteran
|
|
|
Join Date: Jun 2003
Location: Due south of Orlando
Posts: 7,202
Likes: 597
Liked 3,451 Times in 1,412 Posts
|
|
Quote:
Originally Posted by Edmo
|
Not bad, but there's a lot of things he does in that video that you really have to be careful or you could do some serious damage to your gun. Remember he's an experienced gunsmith and knows what he's doing. He doesn't explain too clearly what, were and how the small parts surfaces are that he's honing. Doesn't explain what grit of Arkansas stone etc. I know what he's doing and I can also do it, but I'm just saying, unless you have done this a few times and have gained experience, be careful, it's not for amatuers! Most guys just do the spring kit change.
__________________
Dick
Last edited by diamonback68; 04-11-2012 at 08:52 PM.
|
04-11-2012, 09:50 PM
|
Member
|
|
|
Join Date: Jul 2005
Location: NC
Posts: 30,693
Likes: 57,559
Liked 52,821 Times in 16,468 Posts
|
|
The Centennial models, ie 442, 642 are not hammerless, the hammer is fully enclosed inside the frame.
__________________
Sure you did
|
04-11-2012, 09:55 PM
|
|
Member
|
|
|
Join Date: Nov 2009
Location: Republic of Texas
Posts: 11,345
Likes: 9,368
Liked 17,264 Times in 6,633 Posts
|
|
Watching the video, I was thinking the same thing. He's obviously done that thousands of times, but most of us haven't.
I heard him say that you are polishing, not removing metal, but he didn't talk about the risk of over polishing and removing the hardened metal.
When I did my 442, I did the springs and some lubrication, but that was it. It helped a lot with the trigger pull and I was happy.
Quote:
Originally Posted by diamonback68
Not bad, but there's a lot of things he does in that video that you really have to be careful or you could do some serious damage to your gun. Remember he's an experienced gunsmith and knows what he's doing. He doesn't explain too clearly what, were and how the small parts surfaces are that he's honing. Doesn't explain what grit of Arkansas stone etc. I know what he's doing and I can also do it, but I'm just saying, unless you have done this a few times and have gained experience, be careful, it's not for amatuers! Most guys just do the spring kit change.
|
|
04-11-2012, 10:11 PM
|
|
US Veteran
|
|
|
Join Date: Jun 2003
Location: Due south of Orlando
Posts: 7,202
Likes: 597
Liked 3,451 Times in 1,412 Posts
|
|
Quote:
Originally Posted by GaryS
Watching the video, I was thinking the same thing. He's obviously done that thousands of times, but most of us haven't.
I heard him say that you are polishing, not removing metal, but he didn't talk about the risk of over polishing and removing the hardened metal.
When I did my 442, I did the springs and some lubrication, but that was it. It helped a lot with the trigger pull and I was happy.
|
Exactly my point. I highly suspect, actually I more than suspect, that when you send your gun to the factory for a standard trigger job you aren't getting all that extra honing and polishing you see in that video. They do polish the rebound slide and hone the trigger/hammer sear surfaces somewhat though. The rest is done in the springs area. Probably a 1000-1200 cycles of dry firing will accomplish the same thing.
__________________
Dick
|
04-11-2012, 10:25 PM
|
Member
|
|
|
Join Date: Mar 2012
Location: Broken Arrow OK
Posts: 18
Likes: 0
Liked 1 Time in 1 Post
|
|
Thanks for the input guys. Ill keep all this in mind and for this time pay a gunsmith for his knowledge if I decide to proceed.
|
The Following User Likes This Post:
|
|
04-11-2012, 10:33 PM
|
Member
|
|
|
Join Date: Feb 2011
Posts: 550
Likes: 5
Liked 75 Times in 50 Posts
|
|
My 49 is really heavy, heavier by far than my S-series Highway Patrolman, but I'm going to shoot it until it smooths out. Lots of dry-fire drills should help. Keep in mind that mine had set in a desk drawer or glovebox until I bought it and de-gunked the action.
|
04-11-2012, 11:43 PM
|
Member
|
|
|
Join Date: Feb 2006
Location: USA
Posts: 223
Likes: 11
Liked 18 Times in 13 Posts
|
|
Quote:
Originally Posted by JBradford
So I'd like to do a trigger job on it...
|
just be aware that a trigger job will not make you a better shooter, nor make you more accurate, nor give you trigger control. all of that comes with practice and technique.
try these grips and this grip technique.
Hogue Bantam Grips with Top Finger Groove S&W J-Frame Round butt
PRO TIPS with JERRY MICULEK, shootingusa.com/, sixth panel down - j-frame grip
the hogue bantams will absorb most of the kick while jerry's technique will allow you to better learn trigger control with the j-frame's DA.
|
04-12-2012, 05:08 AM
|
|
Member
|
|
|
Join Date: Jun 2010
Location: Michigan
Posts: 9,656
Likes: 1,362
Liked 1,371 Times in 699 Posts
|
|
There are two references that will allow most anybody to do "passble work" on S&W Revolvers. This opinion is based on personal experience.
I have both of the Jerry Miculek DVD's but the only one anybody really needs is "Trigger Job."
The other reference that I find the most helpful is the book, "The S&W Revolver....A Shop Manual" by Jerry Kuhnhausen.
I have quite a few other references but the two mentioned above pretty much covers what most of us "shade tree" gunsmiths should be trying to do on our own. Actually they go far beyond that level so they will also give you an idea of what the next learning steps would be.
Having done 9 "Trigger Jobs", 8 on J Frames, my personal preference when it comes to spring kits is Wolff, with Wilson my 2nd choice. I purchased over $100 in Apex Kits and after trying them have pulled them from the guns they were installed in.
The reason I prefer Wolff over Wilson is that I have yet to experience 1 light primer strike with the Wolff reduced weight mainsprings, but have had 3 with the Wilson on two different guns.
To be fair to Wilson, this could have been due to idiosyncrasies in those specific actions so it could have been the luck of the draw. Since reliabilty is paramount I didn't even bother trying the reduced weight Wolff mainsprings in those 2 guns, I went right back to stock weight mainsprings, although I did use Wolff over S&W springs.
Based on my trigger pull gauge the Wolff 8.5 lb. mainspring (stock weight) gives me a lighter pull weight than a new, S&W factory 8.5 lb. mainspring. Why that is I have no idea but know that I have yet to have a light primer strike with any of the Wolff springs used, even with CCI primers, so I am very confident that any fail to fire issue would be ammo, not gun, related in any gun that has a Wolff 8.5 lb. mainspring.
__________________
Ogy
|
04-12-2012, 06:41 AM
|
|
Member
|
|
|
Join Date: Dec 2010
Location: NW PA
Posts: 897
Likes: 343
Liked 446 Times in 240 Posts
|
|
Info on my Wolff spring replacement, with some video links-
Best weight for rebound spring for a J
Then scroll down a couple of posts to see my range test results.
__________________
Marty 4513TSW 13-1 642 60-10
Last edited by Martya; 04-12-2012 at 06:44 AM.
|
04-12-2012, 08:05 AM
|
|
Member
|
|
|
Join Date: Sep 2002
Location: Pinson, AL
Posts: 2,106
Likes: 57
Liked 656 Times in 307 Posts
|
|
I guess I'm from a different school of thought here. My CCW's - and home defenders - are not resprung nor do they have their triggers polished. I do deep clean them pre and post break-in - and break them in, either by dry-firing or shooting them, or some combination, to about 1,000 rounds equivalent. This preserves the stronger hammer spring's ability to pop any & all primers - and I can say, in court, if need be, that my CCW's aren't altered. They aren't plinkers! This started with my 296, then my 2" 10 & 642, and, finally, my 4" 64. The 642 is quite serviceable - but the K & L frames are even better (As said, better geometry!). Learn to adapt to your revolver - it's far more reliable that way.
Stainz
|
04-12-2012, 01:27 PM
|
|
US Veteran
|
|
|
Join Date: Jul 2009
Location: Central Arkansas
Posts: 1,200
Likes: 1,349
Liked 1,693 Times in 530 Posts
|
|
The Wilson "Custom-Tune Spring Kit, S&W J Frame 321" I put in my new 642-1 "post lock" made the trigger pull a smidge lighter. However, it was just what this little gun needed.
After hundreds of rounds of various makes and different handload primers (CCI) I feel confident in it making any cartridge go "bang".
Edmo
__________________
TRUTH: Don't delete my posts!
|
04-12-2012, 01:58 PM
|
Member
|
|
|
Join Date: Mar 2012
Location: Broken Arrow OK
Posts: 18
Likes: 0
Liked 1 Time in 1 Post
|
|
Quote:
Originally Posted by f2
just be aware that a trigger job will not make you a better shooter, nor make you more accurate, nor give you trigger control. all of that comes with practice and technique.
try these grips and this grip technique.
Hogue Bantam Grips with Top Finger Groove S&W J-Frame Round butt
PRO TIPS with JERRY MICULEK, shootingusa.com/, sixth panel down - j-frame grip
the hogue bantams will absorb most of the kick while jerry's technique will allow you to better learn trigger control with the j-frame's DA.
|
I completely understand that. I practice all the time and im not wanting this done with those expectations. I just want a softer trigger pull cause this seems abnormally high, even thou after research I know now it's not.
|
04-12-2012, 03:49 PM
|
|
US Veteran
|
|
|
Join Date: Dec 2008
Location: New England
Posts: 4,190
Likes: 3,543
Liked 3,996 Times in 1,627 Posts
|
|
Quote:
Originally Posted by diamonback68
Not bad, but there's a lot of things he does in that video that you really have to be careful or you could do some serious damage to your gun. Remember he's an experienced gunsmith and knows what he's doing. He doesn't explain too clearly what, were and how the small parts surfaces are that he's honing. Doesn't explain what grit of Arkansas stone etc. I know what he's doing and I can also do it, but I'm just saying, unless you have done this a few times and have gained experience, be careful, it's not for amatuers! Most guys just do the spring kit change.
|
Diamondback, I agree. This video lacks MUCH info that the novice would-be gunsmith needs to know. Even SIMPLE things like taking off the sideplate W/O damaging it are not mentioned. I think that there must be better instructional videos than this available....
__________________
'Nam 1968-69.DAV,VFW,NRA Inst.
|
04-12-2012, 04:54 PM
|
|
Member
|
|
|
Join Date: Aug 2007
Location: Oro Valley, Arizona
Posts: 2,370
Likes: 497
Liked 943 Times in 518 Posts
|
|
I have a 642. So far, I have installed a Wolff 8 lb mainspring and 14 lb rebound spring. I have both 13 and 12 lb rebound springs on order, as it is still a bit too stiff for my liking.
If you go this route, be sure to grind the ends of the rebound spring flat, as is the factory rebound spring. Otherwise, it is difficult to install even with a dedicated gunsmithing tool. Grinding is easy with a common drill and grinding stone attachment.
|
04-12-2012, 05:00 PM
|
|
Member
|
|
|
Join Date: Jun 2010
Location: Michigan
Posts: 9,656
Likes: 1,362
Liked 1,371 Times in 699 Posts
|
|
Quote:
Originally Posted by andyo5
I have a 642. So far, I have installed a Wolff 8 lb mainspring and 14 lb rebound spring. I have both 13 and 12 lb rebound springs on order, as it is still a bit too stiff for my liking.
If you go this route, be sure to grind the ends of the rebound spring flat, as is the factory rebound spring. Otherwise, it is difficult to install even with a dedicated gunsmithing tool. Grinding is easy with a common drill and grinding stone attachment.
|
I would advise others to be very careful with any power tools and abrasives.
You can get a nice smooth rebound slide, bottom end edges included,
with a fine polishing stone, in just a few minutes.
__________________
Ogy
|
04-12-2012, 05:11 PM
|
|
Member
|
|
|
Join Date: Aug 2007
Location: Oro Valley, Arizona
Posts: 2,370
Likes: 497
Liked 943 Times in 518 Posts
|
|
Quote:
Originally Posted by ogilvyspecial
I would advise others to be very careful with any power tools and abrasives.
You can get a nice smooth rebound slide, bottom end edges included,
with a fine polishing stone, in just a few minutes.
|
I recommended grinding the ends of the Wolff spring, not the slide.
|
04-12-2012, 05:34 PM
|
|
Member
|
|
|
Join Date: Jun 2010
Location: Michigan
Posts: 9,656
Likes: 1,362
Liked 1,371 Times in 699 Posts
|
|
Quote:
Originally Posted by andyo5
I recommended grinding the ends of the Wolff spring, not the slide.
|
Sorry about that!
I never heard of that being recommended before so my mind must have reverted to what's "normally" done.
With that said, I usually put my springs in a vibrator / tumbler for a while with corn cob media to polish them up a little.
__________________
Ogy
|
04-12-2012, 06:13 PM
|
|
Member
|
|
|
Join Date: Aug 2007
Location: Oro Valley, Arizona
Posts: 2,370
Likes: 497
Liked 943 Times in 518 Posts
|
|
Quote:
Originally Posted by ogilvyspecial
Sorry about that!
I never heard of that being recommended before so my mind must have reverted to what's "normally" done.
With that said, I usually put my springs in a vibrator / tumbler for a while with corn cob media to polish them up a little.
|
The factory rebound spring has the ends ground flat, while the Wolff springs do not. It isn't *too bad* trying to install the Wolff 14 lb rebound spring, but for lesser weights the length is greater (more preload) and they are difficult to compress without them bending and going 'boinnngggg' across the room. Grinding the edges flat makes them alot easier to compress and install. That's probably why the factory does it.
|
The Following User Likes This Post:
|
|
04-12-2012, 06:50 PM
|
Member
|
|
|
Join Date: Oct 2010
Posts: 499
Likes: 124
Liked 101 Times in 81 Posts
|
|
As has been the case on this forum on this issue in the past, there have been alot of different thoughts expressed and that's good. The individual can then decide for themselve's what they want to do. This forum is a great resource. There is alot of tremendous information here and some great people who are willing to share their extensive knowledge and experience.
(for what its worth, I used an ultra fine arkansas stone on my 2 j- frames and have subsequently put several hundred rounds down range in each with no issues )
|
|
Tags
|
442, 638, 640, 642, airweight, brownells, cartridge, ccw, centennial, gunsmith, hammerless, highway patrolman, hogue, j frame, lock, patrolman, primer, round butt, s&w, sideplate, smith & wesson, smith and wesson, smith-wessonforum.com |
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
|
|
|
|