Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Revolvers: 1980 to the Present
o

Notices

S&W Revolvers: 1980 to the Present All NON-PINNED Barrels, the L-Frames, and the New Era Revolvers


Reply
 
Thread Tools Display Modes
  #1  
Old 03-22-2013, 04:41 PM
shouldazagged shouldazagged is offline
Absent Comrade
Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special?  
Join Date: Feb 2013
Location: Louisville, KY, USA
Posts: 19,336
Likes: 53,737
Liked 38,386 Times in 11,801 Posts
Default Buffalo Bore standard pressure .38 Special?

Anyone have any experience using this in 158-grain LSWCHP in a J-frame? They make some pretty strong claims for it--+P velocity from a two-inch barrel, lower pressure and recoil, very soft lead for more reliable expansion, and minimal flash. They say they achieve these remarkable results with advanced powder formulation, as I understand it.

I shoot the old FBI +P load in my EDC, but this stuff sounds fairly impressive if the claims and figures are accurate.
Reply With Quote
The Following User Likes This Post:
  #2  
Old 03-22-2013, 05:19 PM
OKFC05 OKFC05 is offline
Member
Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special?  
Join Date: Aug 2007
Location: Oklahoma
Posts: 8,158
Likes: 3,604
Liked 5,199 Times in 2,172 Posts
Default

It is good ammo, BUT don't expect miracles from a stubby, whether you use your present load or others. Marketing is marketing.

By the way, getting low PEAK pressure does not make for LOW RECOIL since the area under the pressure curve is what does the work pushing out the bullet, and more bullet speed makes more recoil, all else being equal. There is no free lunch in internal ballistics.
__________________
Science plus Art
Reply With Quote
The Following User Likes This Post:
  #3  
Old 03-22-2013, 06:33 PM
photoman's Avatar
photoman photoman is offline
Member
Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special?  
Join Date: Oct 2000
Location: The Great State of Texas
Posts: 5,056
Likes: 522
Liked 1,907 Times in 787 Posts
Default

It may be low pressure but it's not low recoil. They make quality ammo.
__________________
Centennial Every Day
Reply With Quote
  #4  
Old 03-22-2013, 07:49 PM
shouldazagged shouldazagged is offline
Absent Comrade
Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special?  
Join Date: Feb 2013
Location: Louisville, KY, USA
Posts: 19,336
Likes: 53,737
Liked 38,386 Times in 11,801 Posts
Default

I'm not really concerned about the recoil (the EDC is a 640 with Pachmayr Compac grips, not an Airweight), nor do I expect a snubby to do the work of an RPG. The low recoil was one of their claims, as I recall. The whole package looked a little iffy to me, which is why I asked. Couldn't quite figure how they could get in excess of 800fps with 158-grain bullets from a two-inch barrel with standard pressure.

How about the flash level? My elderly eyes don't readjust nearly as quickly as they used to--one of several reasons .357 Magnum is not for me anymore. They say their flash retardant is very effective.
Reply With Quote
  #5  
Old 03-22-2013, 07:53 PM
wx7b's Avatar
wx7b wx7b is offline
Member
Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special?  
Join Date: Aug 2011
Location: Greeley, CO
Posts: 176
Likes: 1,979
Liked 101 Times in 66 Posts
Default

I bought it because of the low flash for my 642. Have not shot them yet.
Reply With Quote
  #6  
Old 03-22-2013, 07:56 PM
QB Too QB Too is offline
Member
Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special?  
Join Date: Mar 2004
Location: Carrollton, TX
Posts: 131
Likes: 1
Liked 48 Times in 17 Posts
Default

I purchased some but have not yet been able to get to the range. I'll post my results if I ever get to fire it. Going to fire out of a Ruger GP100 3" barrel and a S&W 360 Airweight Snub.

I bought both the (1) Standard Pressure Short Barrel Low Flash Heavy .38 Special Ammo - 158 gr. Soft Lead SWC-HC (850fps/M.E. 253 ft. lbs.) and the (2) Standard Pressure Short Barrel Low Flash Heavy .38 Special Ammo - 125gr. Jacketed Hollow Point (900fps/M.E. 225 ft. lbs.

I was just curious and thought, what the heck.
Reply With Quote
  #7  
Old 03-24-2013, 01:04 PM
hotrod150's Avatar
hotrod150 hotrod150 is offline
Member
Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special?  
Join Date: Sep 2012
Location: western Washington
Posts: 2,647
Likes: 1
Liked 763 Times in 454 Posts
Default

My old Speer #10 handloading book shows several standard-pressure 158 gr lead bullet loads producing around 950 fps out of the 6" test revolver, which should equate to between 800-850 out of a 2". This was using the cannister-grade powders of the day. Using specially blended powders (not unusual for cartridge mfr's) to optimize results for snubbies is certainly possible,so I think their claims are quite likely true or at least not exagerated too much.
We'll have to take BB's word for the standard pressure, but the velocity is easy to check if you have access to a chronograph. Has anyone here chrono'd them out of a snubbie?
Reply With Quote
  #8  
Old 03-24-2013, 01:10 PM
357-RevolverGuy's Avatar
357-RevolverGuy 357-RevolverGuy is offline
Member
Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special?  
Join Date: Jan 2013
Location: North Carolina, USA
Posts: 1,469
Likes: 1,303
Liked 1,959 Times in 663 Posts
Default

I had fired some Buffalo Bore in .38+P that felt like standard .357. And I've also fired some of their .357 Mag that seriously felt like .44 Mag. They are serious.
__________________
Ephesians 6 (Armor of God)
Reply With Quote
  #9  
Old 03-24-2013, 06:57 PM
chief38's Avatar
chief38 chief38 is online now
Member
Buffalo Bore standard pressure .38 Special?  
Join Date: Apr 2006
Posts: 17,759
Likes: 7,836
Liked 25,615 Times in 8,661 Posts
Default

I have become a BIG BB fan and carry their HEAVY 38 Special 158 grain +P LSWCHP-GC in my Model 60 and after I personally chronographed them many times, they truly do a 1025 - 1040 feet per second out of a 2" barrel! Their claims and stated ballistics are 100% correct! These ballistics are just about low end .357 Magnum out of a a snubby. Not only are they HOT, but they are VERY accurate and VERY consistent as well.

Their NON +P 158's will do about 860 - 880 fps (out of a 2" snub) and are actually hotter than the Big 3's +P offerings. GREAT ammo - just plan on training and familiarization if you intend on using this load for defense as it does take some getting use to.
Reply With Quote
  #10  
Old 03-24-2013, 06:57 PM
Dave T Dave T is offline
Member
Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special? Buffalo Bore standard pressure .38 Special?  
Join Date: Nov 2002
Location: Mesa, Arizona
Posts: 2,556
Likes: 882
Liked 1,719 Times in 549 Posts
Default

I have chronographed BB's 158g gas check +P load and it is right on for their claimed velocity, almost to the exact fps. I would expect the load you are considering to do what they claim. I'm very impressed with their ammo and carry it in my "38 caliber" revolvers.

Dave
__________________
RSVN '69-'71
PCSD (Ret)
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Buffalo Bore Plus Pressure 158gr LSWCHPGC in 638-3? sonofthebeach S&W Revolvers: 1980 to the Present 24 07-06-2014 02:25 PM
Buffalo Bore .38 Special 158gr LSWHC: standard or +P for a 3" barrel? Hapworth Ammo 13 07-04-2014 08:16 AM
357 J frames, pressure, and buffalo bore ammo island S&W Revolvers: 1980 to the Present 17 02-03-2014 09:08 PM
Review of Buffalo Bore 38 spl. 158gr Standard Pressure Dragon88 Ammo 12 08-08-2011 09:30 PM
Anyone used this Buffalo Bore standard 38 stuff? aterry33 Ammo 10 05-02-2010 12:11 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 10:02 AM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)