|
|
05-27-2013, 07:13 PM
|
Member
|
|
|
Join Date: May 2013
Location: Sweden
Posts: 6
Likes: 0
Liked 0 Times in 0 Posts
|
|
pls help problem with 357 magnum model 586
hejsan
have a problem that I hope someone can help me with
bought a 357 magnum model 586 it is brand new used only once.
so one day when I would pick up the
so fell cylinder opener away from the place it sat on have not touched it or lost it or something weird. when you try to insert the screw into reverse again so it is not possible it is that the screw is broken '. should it be so small gap. just millimeters it and try to insert the screw on. screw goes the o swapped side but it does not matter.
what can you do? you have to open the entire gun?
do you think a screw is broken?
please help me
with kind regards
Last edited by tallola187; 05-27-2013 at 07:20 PM.
|
05-27-2013, 07:25 PM
|
|
Moderator
|
|
|
Join Date: Jun 2007
Posts: 26,906
Likes: 989
Liked 19,027 Times in 9,310 Posts
|
|
Are you referring to the screw that holds the cylinder latch in place, or the one that holds the yoke (arm that holds the cylinder itself) into the frame?
__________________
Alan
SWCA LM 2023, SWHF 220
|
05-27-2013, 07:44 PM
|
Member
|
|
|
Join Date: May 2013
Location: Sweden
Posts: 6
Likes: 0
Liked 0 Times in 0 Posts
|
|
mean cylinder latch it usually happen? what should you do?
Praise sorry for my english
|
05-27-2013, 07:46 PM
|
|
US Veteran
|
|
|
Join Date: Mar 2010
Location: R.T. P, area NC
Posts: 9,718
Likes: 29,595
Liked 23,020 Times in 5,791 Posts
|
|
Quote:
do you think a screw is broken?
|
If the screw holding the cylinder latch was broken you should be able to see that right away.
Try fitting the screw and moving the latch, back and forth, until the screw starts in the hole in the frame.
|
05-27-2013, 07:52 PM
|
|
Moderator
|
|
|
Join Date: Jun 2007
Posts: 26,906
Likes: 989
Liked 19,027 Times in 9,310 Posts
|
|
The threads on the screw are pretty fine, so as old bear mentioned it may take a little wiggling of the latch and the screw to start tightening it onto the post that attaches the latch to the frame.
__________________
Alan
SWCA LM 2023, SWHF 220
|
05-27-2013, 08:19 PM
|
Member
|
|
|
Join Date: May 2013
Location: Sweden
Posts: 6
Likes: 0
Liked 0 Times in 0 Posts
|
|
oki I'll try to reinstall the screw hard while I move on the thing it is in the back and forth?
|
05-27-2013, 08:42 PM
|
Member
|
|
|
Join Date: Apr 2013
Location: Alma,AR
Posts: 147
Likes: 303
Liked 67 Times in 40 Posts
|
|
Tallola87, reading about your problem. I have a few questions, first: do you have the screw and the latch in hand?
Second: If you have the screw, look a the gun where the latch would set. Do you see a hole or is it smooth? If smooth then I would say the screw has broken, take it to the gun shop. If you can see the hole for the screw, try inserting the screw,without the latch. If the screw will thread in, without force, perfect. If force is required then the screw and/or the latch mount thread has been damaged, take this to the gunsmith.
If the screw threads into the hole, without problem then it should be easy to mount the latch and insert the screw. Might use a mild thread sealer to hold the screw inplace after it has been tightened.
Good Luck
|
05-27-2013, 09:46 PM
|
Member
|
|
|
Join Date: May 2013
Location: Sweden
Posts: 6
Likes: 0
Liked 0 Times in 0 Posts
|
|
Hi
I have the screw and lock in my hand
I can see a hold nte not smooth to go and screw it in.. not easy as the others .. direction is deep so I stop the screw there, but that has screwed your it so it stays there if you know this but will try now little thanks for your response
|
05-27-2013, 09:51 PM
|
Member
|
|
|
Join Date: Apr 2013
Location: Alma,AR
Posts: 147
Likes: 303
Liked 67 Times in 40 Posts
|
|
Tallola187, sounds like you have everything under control.
Good Luck
|
05-27-2013, 10:27 PM
|
Member
|
|
|
Join Date: May 2013
Location: Sweden
Posts: 6
Likes: 0
Liked 0 Times in 0 Posts
|
|
nothing is wrong screw is intact are holes but it will not screw in. ... is the picture of someone who has a working magnum? you get to see how the way to be?
|
|
Posting Rules
|
|
|
|
|