|
|
04-16-2015, 01:39 PM
|
|
Member
|
|
|
Join Date: Mar 2014
Location: Alabama
Posts: 53
Likes: 101
Liked 13 Times in 11 Posts
|
|
Best revolver cleaning method
What's up guys I've recently acquired a surly new. 442 from a friend. My friend has accidentally put way to much oil in this thing. I mean it's weeping out of the gun in the safe. I know if I pop the side plate I could get it out but what is the best way to get this out without doing that? I have some gun scrubber but don't know if it will ruin the finish. Any advice would be awesome. Thanks.
|
04-16-2015, 01:43 PM
|
|
Moderator
|
|
|
Join Date: Jun 2007
Posts: 26,900
Likes: 989
Liked 19,023 Times in 9,307 Posts
|
|
Non-chlorinated brake cleaner works great. I wouldn't let it sit on the finish for long periods. Wipe down, lightly lubricate the internals and you should be good to go.
__________________
Alan
SWCA LM 2023, SWHF 220
|
04-16-2015, 01:46 PM
|
Member
|
|
|
Join Date: Oct 2007
Location: Arizona
Posts: 3,222
Likes: 2,905
Liked 5,333 Times in 1,869 Posts
|
|
I personally would take the side plate off and really clean it but I suppose you can do the following. Remove the grips,crane and cylinder. Cock the hammer and spray gun scrubber into the hammer recess, the recess around the trigger and up into the underside of the frame. Use some canned aired to blow the gunk out.
This is not to me the best of solutions but should improve the situation somewhat.
jim
|
04-16-2015, 04:29 PM
|
|
Member
|
|
|
Join Date: Dec 2009
Location: South Texas & San Antonio
Posts: 33,629
Likes: 241
Liked 29,143 Times in 14,091 Posts
|
|
Spray carb/choke cleaner works well, also, you can give it a bath in mineral spirits. That's the most useful solvent in my garage. Let it dry, lube sparingly with light oil, and replace the sideplate.
|
The Following User Likes This Post:
|
|
04-16-2015, 05:24 PM
|
|
Member
|
|
|
Join Date: Apr 2013
Location: New Mexico
Posts: 2,637
Likes: 2,354
Liked 3,824 Times in 1,348 Posts
|
|
Whenever I get a "new" used gun I use a spray cleaner like Powder Blast. I liberally spray into all the orifices and let it drip out for a short while. Next I use compressed air to blow out all the remaining cleaner and dirt. Finally I apply a liberal amount of Hoppe's gun oil into the same orifices and once again use compressed air to distribute the oil and remove the excess.
I would never take off the side plate unless there is a mechanical problem.
|
The Following 2 Users Like Post:
|
|
04-16-2015, 06:28 PM
|
Member
|
|
|
Join Date: Mar 2012
Posts: 5,831
Likes: 3,902
Liked 5,902 Times in 2,543 Posts
|
|
Too much oil in a revolver isn't much of an issue -- not enough to pop the sideplate or spray something that will dry up every drop of oil, requiring you to re-oil it what you just removed the oil from.
Remove the grips; insert canned air in the direction of the innards and spray. This will force much of the excess oil out. Wipe 'er down. Repeat a few times and put put away.
|
The Following 6 Users Like Post:
|
|
04-19-2015, 10:15 PM
|
|
Member
|
|
|
Join Date: Mar 2014
Location: Alabama
Posts: 53
Likes: 101
Liked 13 Times in 11 Posts
|
|
Ended up pulling the side plate. Glad I did because as soon as the cover came off it dumped lube all over my Tekmat. This thing was swimming in oil. Hosed out the lock work and lightly oiled in all the critical spots and reassembled. The gun works perfectly. Thanks for all the suggestions. I didn't want to pop the cover but when you shake a gun and oil slings out of it it really deters you from shoving it in you're pocket.
|
The Following User Likes This Post:
|
|
|
Posting Rules
|
|
|
|
|
All times are GMT -4. The time now is 08:26 AM.