|
|
10-21-2017, 05:02 AM
|
Member
|
|
|
Join Date: Mar 2015
Location: Broome County NY
Posts: 27
Likes: 23
Liked 8 Times in 6 Posts
|
|
Trouble with trigger
I am having issues with my 586-2. When I cycle the hammer back after several rotations it is sticking and won’t continue it’s motion of cocking back. I have to tap the right side plate and then i am able to go thru regular motions of cocking and shooting ???
|
10-21-2017, 06:10 AM
|
|
Member
|
|
|
Join Date: Apr 2006
Posts: 17,820
Likes: 7,852
Liked 25,742 Times in 8,697 Posts
|
|
It could be some old fashioned crud or a piece of debris inside but you will have to pop the Side Plate off to see what is happening. If that's not the problem check the Hammer Stud - might have broken off. If you are not adept at this I'd suggest visiting a GOOD LGS or sending it back to the Factory.
|
The Following User Likes This Post:
|
|
10-21-2017, 06:56 AM
|
Member
|
|
|
Join Date: May 2012
Location: North Georgia
Posts: 4,540
Likes: 2,863
Liked 9,121 Times in 3,216 Posts
|
|
Loose side plate screws?
Try tightening them down.
|
10-21-2017, 07:06 AM
|
Member
|
|
|
Join Date: Mar 2015
Location: Broome County NY
Posts: 27
Likes: 23
Liked 8 Times in 6 Posts
|
|
I had to purchase # 34 screw on schematics as it was missing (it’s the way I received it after my brother-inlaw passed a way. So i tighten them and it works for about 8-10 rotations and then binds us, I tap side plate and god to go for another few rotations before it does it again. I cleaned inside and everything seems to flow in movement and I can see where a portion of the parts “move towards right side plate and it catches trigger mechanism . Wished I could show a picture on here
|
10-21-2017, 08:45 AM
|
Member
|
|
|
Join Date: May 2012
Location: North Georgia
Posts: 4,540
Likes: 2,863
Liked 9,121 Times in 3,216 Posts
|
|
With side plate off, parts will shift and then be out of sync.
Look at side plate. Was it buffed way down or something
that allows innards to shift with plate on and screws
tightened down?
And when plate is on, are you sure it is seated (bottomed
out) snugly against the frame?
If it works for a short time, something is coming loose.
Was your relative a table top gunsmith who might have buffed
the individual parts as well?
Another thought is does the trigger return to reset vigorously
or is it sluggish? Trigger return spring might have been cut
or a very light one installed which doesn't allow full reset.
But really, the best bet is to send it back to Smith.
Last edited by UncleEd; 10-21-2017 at 08:50 AM.
|
The Following User Likes This Post:
|
|
10-21-2017, 08:59 AM
|
Member
|
|
|
Join Date: Sep 2014
Location: North Central Ohio
Posts: 921
Likes: 862
Liked 597 Times in 332 Posts
|
|
Quote:
Originally Posted by Proud Smith and wesson
I had to purchase # 34 screw on schematics as it was missing (it’s the way I received it after my brother-inlaw passed a way. So i tighten them and it works for about 8-10 rotations and then binds us, I tap side plate and god to go for another few rotations before it does it again. I cleaned inside and everything seems to flow in movement and I can see where a portion of the parts “move towards right side plate and it catches trigger mechanism . Wished I could show a picture on here
|
Sounds erratic so possibly there is debris in the works that occasionally is causing a bind up? It is possible to get a brass brush bristle that has become separated from a cleaning brush in through the hand window slot that can get lodged internally.
Is there any chance you have replaced the grips? Sometimes the location of new grip screw interferes with the mainspring. You could remove the grips and try to cycle the gun just as a simple check for function.
If you wish to email me a picture I can post it for you...
Karl
|
The Following User Likes This Post:
|
|
10-21-2017, 09:18 AM
|
Vendor
|
|
|
Join Date: Jan 2010
Location: Kansas City area
Posts: 6,190
Likes: 54,459
Liked 13,612 Times in 4,290 Posts
|
|
Could be a broken trigger stud. You might not even notice unless you take the trigger out. Often times when a gun is acting weird, that is the cause. Some problems are hard to diagnose long distance.
|
The Following 5 Users Like Post:
|
|
10-21-2017, 11:43 AM
|
Member
|
|
|
Join Date: Jun 2012
Location: Demon-class planet
Posts: 7,403
Likes: 29,169
Liked 8,461 Times in 3,772 Posts
|
|
Very difficult, if not nigh impossible to diagnose "over the phone." We can't know what a prior owner may have done inside to "improve" the gun. By all means, try removing the grips and cycling the action, as ontargetagain suggested. Could be as simple as that. At the very least, have the gun examined by a competent gunsmith who can diagnose the problem hands-on. Sounds like something that is not simply going away. Good luck, wish you well.
Kaaskop49
Shield #5103
|
The Following 2 Users Like Post:
|
|
10-22-2017, 04:41 PM
|
Member
|
|
|
Join Date: Mar 2015
Location: Broome County NY
Posts: 27
Likes: 23
Liked 8 Times in 6 Posts
|
|
Thanks to you fellas!! I do not know what if anything may have been done. Prior but will get it to a good gunsmith here and ask them to do a good go over. I sure they will be able to do it safely and I am not a gun smith so I love my “click bangs” and don’t want it to go boom for sure. I’ll see if I can get the picture on here and I believe I pointed with the screw driver at where I believe the problem lies but like I said I’m not a gun smith
|
|
Posting Rules
|
|
|
|
|