Smith & Wesson Forum

Go Back   Smith & Wesson Forum > Smith & Wesson Revolvers > S&W Revolvers: 1980 to the Present
o

Notices

S&W Revolvers: 1980 to the Present All NON-PINNED Barrels, the L-Frames, and the New Era Revolvers


Reply
 
Thread Tools Display Modes
  #1  
Old 01-11-2020, 11:33 PM
1BadSmith's Avatar
1BadSmith 1BadSmith is offline
Member
Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)...  
Join Date: Oct 2017
Location: Liberty Township, WI
Posts: 111
Likes: 35
Liked 149 Times in 48 Posts
Default Smith 625 JM (previous owner issues)...

I took in a 625 JM on trade the other day--deal of a lifetime!! It had about $400+ in accessories with it, and the gun is like new, with factory box and paperwork. I already have a 625PC, which I love. The previous owner of the JM got all set up to shoot competition, and never really did. Long story short, he had trigger work done--it is extremely dangerous!! Light strikes, and hair trigger. It's GOT TO be fixed!! Also it is missing the spring in the ejector rod housing for some reason. I spoke to Smith yesterday, and asked if they could put the same action tuning in as my 625 PC, and they said no problem, they would also handle the spring issue. Anyhow, 6 month wait and about $300. Really didn't want to spend that or wait that long either. Any advice, comments, suggestions, etc...Thanks.

Last edited by 1BadSmith; 01-11-2020 at 11:35 PM.
Reply With Quote
  #2  
Old 01-12-2020, 01:57 AM
jframejoey jframejoey is offline
Member
Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)...  
Join Date: Jan 2013
Location: New England
Posts: 1,357
Likes: 10,048
Liked 1,001 Times in 491 Posts
Default

Put ejector rod spring, rebound slide spring and new factory standard hammer spring in and see if it works safely. If not then someone fiddle faddled with the trigger and hammer contact points to a dangerous level.
Reply With Quote
The Following 3 Users Like Post:
  #3  
Old 01-12-2020, 03:10 AM
robertrwalsh robertrwalsh is offline
SWCA Member
Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)...  
Join Date: May 2008
Location: Peoples Republic of Calif
Posts: 4,643
Likes: 1,226
Liked 5,987 Times in 2,133 Posts
Default

Any competent local smith can change the springs back for you. If it is still an issue after that, you want to reconsider your options. That will be quicker and cheaper than sending it back to the mother ship.
Reply With Quote
The Following 2 Users Like Post:
  #4  
Old 01-12-2020, 04:28 AM
kaaskop49 kaaskop49 is offline
Member
Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)...  
Join Date: Jun 2012
Location: Demon-class planet
Posts: 7,404
Likes: 29,169
Liked 8,461 Times in 3,772 Posts
Default

^^^^ what THEY said. This thread reminds me of the accessorizing/modding craze on 1911s in the 1970s. The used gun cases in LGSs held many such guns when the original owners became tired of playing with them. My 'favorite' mod: stippling the front strap to improve grip on the gun, then installing rubber grips to prevent the stippling from abrading the shooter's hand...

Once bought a used Python from another LEO that could not be fired single-action: the hammer would catch on the trigger and simply return to the full-rest position. My 'smith said he could bring it back to factory standard. Lovely gun after he did so.

Kaaskop49
Shield #5103
Reply With Quote
The Following 5 Users Like Post:
  #5  
Old 01-12-2020, 10:56 AM
scooter123 scooter123 is offline
Member
 
Join Date: Jan 2009
Location: Metro Detroit, Michigan
Posts: 6,919
Likes: 179
Liked 4,294 Times in 2,106 Posts
Default

You don't mention how "light" that dangerous trigger is. If it's 3 to 4 lbs in single action that is a factory stock trigger. If it's less than about 2.5 lbs that means the sear on the hammer has been re-ground and you should plan on replacing the hammer. You can purchase a new hammer from either Numrich or Brownells but finding a color match to the original flash chromed hammer may mean waiting on one to arrive. Typically the replacement parts are the blued MIM versions.

Next step in reversing that "action job" will likely require replacing the mainspring and strain screw, both parts that are easy to obtain from Brownells.

The final touch will be to replace the Rebound Spring, also easy to obtain from Brownells. BTW, when ordering the replacement rebound spring also get yourself a rebound spring tool. They look sort of like a bent screwdriver in the catalog and are essential for getting the rebound spring back in the revolver. I'll also recommend getting a 14 lbs rebound spring instead of the factory original 16 lbs. rebound spring. Because it does lighten the Single action trigger from 4 lbs. to 3 lbs. which I find perfectly safe to use and a bit easier to work with for precision shooting.


Concerning tuning of a S&W revolver that is something I feel is necessary for any modern S&W revolver. The key is to tune the trigger so that it's 100% reliable with any commercial ammo you can purchase. BTW, Remington has the hardest primers I've encountered and I prefer Remington cases for reloading so I shoot some any time I need fresh cases. The point of perfect reliability that I've set my revolvers to is 9 lbs. on the dot. Perhaps a bit heavier than the perfect minimum but a bit of a cushion is a good thing when it's about reliable ignition. Tuning the trigger of a modern medium or large frame S&W to this level is actually quite simple. The recipe is a 14 lbs. Rebound Spring, a Factory Mainspring, and a Factory Strain Screw with 0.020 to 0.035 inch filed off the tip. Yeah the recipe really is that simple. Note, a good accurate trigger gage is a real asset but not absolutely essential. Go too far filing the Strain screw and you'll have one reason why I recommend having spares. BTW, the second reason for spares is that Strain Screws do wear out due to peening of the tip.
Reply With Quote
The Following User Likes This Post:
  #6  
Old 01-12-2020, 11:10 AM
Old_Cop Old_Cop is offline
Member
Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)...  
Join Date: Jan 2011
Location: Crawford County PA
Posts: 3,704
Likes: 4,368
Liked 6,709 Times in 2,417 Posts
Default

If a deal is too good to be true, it probably is. Have a S&W trained armorer check it out. Hammer light is an easy fix, replacing springs too.
__________________
Made it, Ma! Top of the world!
Reply With Quote
The Following User Likes This Post:
  #7  
Old 01-12-2020, 01:22 PM
1-1917 1-1917 is offline
Member
Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)...  
Join Date: Mar 2000
Location: Center Point, Texas
Posts: 275
Likes: 51
Liked 407 Times in 120 Posts
Default

Have you just tried tightening the strain screw?
__________________
Go West young man..
Reply With Quote
The Following 2 Users Like Post:
  #8  
Old 01-14-2020, 07:33 PM
JDinAZ's Avatar
JDinAZ JDinAZ is offline
Member
Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)... Smith 625 JM (previous owner issues)...  
Join Date: Jul 2017
Location: AZ
Posts: 498
Likes: 42
Liked 463 Times in 170 Posts
Default

Previous endorsement retracted........
__________________
R/S
J.D.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Smith & Wesson 380 EZ issues? George9 Smith & Wesson M&P Pistols 9 05-09-2019 09:36 AM
New to me Md. 15-3; and thanks to the previous owner whomever that may be cporfe S&W Revolvers: 1961 to 1980 9 03-06-2019 06:09 PM
New m&p 9mm owner with issues.. Ortiz11b Smith & Wesson M&P Pistols 10 09-11-2012 07:20 PM
new 5906 owner issues magill91 Smith & Wesson Semi-Auto Pistols 13 03-05-2012 08:39 PM
New 9 mm owner issues D L B Smith & Wesson M&P Pistols 20 08-06-2011 09:38 AM

Powered by vBadvanced CMPS v3.2.3
smith-wessonforum.com tested by Norton Internet Security smith-wessonforum.com tested by McAfee Internet Security

All times are GMT -4. The time now is 02:03 PM.


Smith-WessonForum.com is not affiliated with Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC)